764071

Vonroc OT501DC Manual

6
Zoom out
Zoom in
Previous page
1/28
Next page
6
EN
WWW.VONROC.COM
with a standardised test given in EN 60745; it may
be used to compare one tool with another and as
a preliminary assessment of exposure to vibration
when using the tool for the applications mentioned:
- using the tool for different applications, or with
different or poorly maintainted accessories,
may significantly increase the exposure level
- the times when the tool is switched off or when
it is running but not actually doing the job, may
significantly reduce the exposure level.
Protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work patterns.
DESCRIPTION
The numbers in the text refer to the diagrams on
page 2.
1. On/off switch
2. Speed adjustment wheel
3. Mounting point for accessories
4. Grip
5. Quick change lever
6. Work light
7. Battery (not included)
8. Battery unlock button
3. ASSEMBLY
Before any work on the power tool, remove
the battery.
The battery must be charged before first use.
Inserting the battery into the machine (Fig. C)
Ensure that the exterior of the battery is
clean and dry before connecting to the
charger or machine.
1.
Insert the battery (7) into the base of the machine
as shown in Fig. C.
2. Push the battery further forward until it clicks
into place.
Removing the battery from the machine (Fig. C)
1. Push the battery unlock button (8).
2. Pull the battery out of the machine like shown
in Fig. C.
Removing and mounting accessories (fig. B)
Worn or damaged accessories must be
replaced immediately.
Only use sharp and undamaged accessories.
•
Release the quick change lever (5) and slide the
accessory forward to remove from the holder.
• Slide the accessory in the holder and fasten the
quick change lever (5).
The sanding pad and the sanding paper must be
used for sanding applications.
4. OPERATION
Switching on and off (fig. A)
• To switch on the machine, slide the on/off
switch (1) to the front.
• To switch off the machine, slide the on/off
switch (1) to the rear.
Setting the speed (fig. A)
The speed adjustment wheel is used for setting the
speed. The speed adjustment wheel can be set to 6
positions. The ideal speed depends on the applica-
tion and on the material to be worked.
Do not set the speed during use.
• Turn the speed adjustment wheel (2) to the
required position.
Hints for optimum use
• Clamp the workpiece. Use a clamping device for
small workpieces.
• Draw a line to define the direction in which to
guide the accessory.
• Firmly hold the machine by the grip.
• Switch on the machine.
• Wait until the machine has reached full speed.
• Place the accessory on the workpiece.
• Slowly move the machine along the pre-drawn
line, firmly pressing the accessory against the
workpiece.
• Do not apply too much pressure on the machine.
Let the machine do the work.
• Switch off the machine and wait for the machine
to come to a complete standstill before putting
the machine down.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc OT501DC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc OT501DC in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info