Manual Vonroc MS504AC (page 18 of 104) (English, German, Dutch, French, Italian, Polish, Spanish)

778562

Zoom out

Zoom in

1/104

WWW.VONROC.COM

Fine-tuning

Prior to any adjustment work disconnect

the mains power plug.

To ensure precise cuts, the basic settings of the

saw must be checked and adjusted before ﬁrst use,

as well as necessary after intensive use. Suitable

special tools are required for this. Vonroc after-sales

will help handling this work quickly and reliably.

Fine-tuning the laser (Fig. Q)

Note: To test the laser function, the power tool

must be connected to the power supply.

While adjusting the laser (e.g. when moving

the tool arm), never activate the on/off

switch. Accidental starting of the power tool

can lead to injuries.

If the laser (18) ceases to indicate the correct cut-

ting line, you can readjust the laser. To do so:

1. Loosen the laser adjustment screws (48) and

set the laser by moving it until the laser beam

strikes the teeth of the saw blade (6);

2. Tighten the laser adjustment screws (48).

Fine-tuning the 0° bevel angle (Fig. R, S)

1. Adjust the mitre and bevel angle to 0°;

2. Lower the handle (2) and secure it using the

position lock knob (38);

3. Lock the slide movement using the locking bolt

for slide rails (29);

4. Set an angle gauge to 90° and place it on the

table (11), as shown on ﬁgure S. The leg of the

angle gauge must be ﬂush with the saw blade

(6) along its entire length;

5. Loosen the lock nut for 0° bevel angle (50);

6. Adjust the stop bolt for 0° bevel angle (32) until

the leg of the angle gauge is ﬂush with the saw

blade along its entire length;

7. Re-tighten the lock nut for 0° bevel angle (50).

Subsequently check the position of the angle indica-

tor (19). If necessary loosen the pointer using a Phi-

lips screwdriver, set to position 0° on the scale for

bevel angle (20) and re-tighten the retaining screw.

Fine-tuning the 45° bevel angle (Fig. R, T)

1. Adjust the mitre and bevel angle to 45°;

2. Lower the handle (2) and secure it using the

position lock knob (38);

3. Lock the slide movement using the locking bolt

for slide rails (29);

4. Set an angle gauge to 90° and place it on the

table (11), as shown on ﬁgure T. The leg of the

angle gauge must be ﬂush with the saw blade

(6) along its entire length;

5. Loosen the lock nut for 45° bevel angle (49);

6. Adjust the stop bolt for 45° bevel angle (31)

until the leg of the angle gauge is ﬂush with the

saw blade along its entire length;

7. Re-tighten the lock nut for 45° bevel angle (49).

Subsequently check the position of the angle indica-

tor (19). If necessary loosen the pointer using a Phi-

lips screwdriver, set to position 45° on the scale for

bevel angle (20) and re-tighten the retaining screw.

Fine-tuning the 0° mitre angle (Fig. U, V)

1. Set an angle gauge to 0° on the table (11) and po-

sition it between the fence (9) and the saw blade

(6);

2. The leg of the angle gauge must be ﬂush with the

saw blade (6) along its entire length;

3. Loosen the locking bolts for adjustable fence

(35) and subsequently loosen the safety bolts for

adjustable fence (36).

4. Remove both left and right adjustable fences (7),

revealing the fence bolts (51).

5. Loosen all four fence bolts (51) and adjust the

fence (9) until the leg of the angle gauge is ﬂush

with the saw blade along its entire length;

6. Retighten all four fence bolts (51) again. Subse-

quently check the position of the angle indicator

(17). If necessary loosen the pointer using a

Philips screwdriver, set to position 0° on the scale

for mitre angle (16) and re-tighten the retaining

screw.

7. Mount both left and right adjustable fences (7).

Tighten the locking bolts for adjustable fence

(35) and subsequently tighten the safety bolts

for adjustable fence (36).

5. MAINTENANCE

Always make sure that the machine is not

connected to the mains electricity when you

carry out any maintenance of the mechanism.

Clean the machine casings regularly with a soft

cloth, preferably after each use. Make sure that the

ventilation openings are free of dust and dirt. Re-

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc MS504AC in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 12.98 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Vonroc MS504AC Manual

Product: