778562

Vonroc MS504AC Manual

15
Zoom out
Zoom in
Previous page
1/104
Next page
EN
15
WWW.VONROC.COM
(40), only loosen it.
3. Fold the retracting protective guard (5) upwards
until the clamping bolt (42) can be accessed
freely, as shown on figure G2;
4. Insert the hex key into the clamping bolt (42).
The retracting protective guard (5) can be
released, it will fold onto the hex key.
5. Mount the clamping flange (41). Ensure the
flat sides of the clamping flange correspond
with the flat sides of the blade shaft. Also make
sure the convex side of the clamping flange is
mounted to the outside.
6. Mount the clamping bolt (42) and turn it using
the hex key whilst at the same time pressing
the spindle lock (43), until it engages.
7. Firmly hold the spindle lock (43) and fasten the
clamping bolt (42) by turning it anti-clockwise.
Dust extraction (fig. A, B, W, X)
Provide good ventilation at the workplace.
Wear dust protection.
The dust from materials such as lead paint and
some types of wood can be harmful to your health.
Breathing in this dust can cause allergic reactions
and/or cause respiratory illnesses for the user or
people in the near vicinity. Certain dusts, such as
oak or beech dust, are classified as carcinogenic,
especially in conjunction with wood treatment
additives (chromate, wood preservative). We stron-
gly advise to use a dust extraction system that is
suitable for the material wherever possible.
Avoid dust accumulation at the workplace.
Dust can easily ignite.
The dust extraction system can be blocked by dust,
chips or fragments of the workpiece. Thus, it must
be cleaned regularly. To do so:
1.
Disconnect the mains plug from the power supply.
2.
Wait until the saw blade has come to a complete
stop.
3. Remove any blockage if necessary
Mounting the dust bag (Fig. W)
Press in the clamp of the dust bag (26) and slide
it onto the dust outlet (28) on the back of the ma-
chine. The dust bag stays in place when releasing
the clamp.
Connecting a vacuum cleaner (Fig. X)
The dust extractor must be suitable for the
material being worked.
When vacuuming dry dust that is especially
detrimental to health or carcinogenic, use a
special dust extractor.
A vacuum cleaner hose can be connected to the
dust outlet (28). To do so, simply connect the vacu-
um hose to the dust extraction spout.
4. OPERATION
Before you turn on the machine, always
check that the saw blade is fitted correctly.
The blade must turn smoothly.
Always check the protective guards before
use.
For all cuts, it must first be ensured that the
saw blade at no time can come in contact
with the fence, workpiece clamp or other
machine parts. Remove any mounted
auxiliary stops or adjust them accordingly.
Supporting the workpiece (fig. H)
Workpieces must always be properly supported.
The table extensions (10) can be extended left and
right to support a workpiece. To do so:
1. Loosen the locking bolt for table extension (34);
2. Move the table extension (10) to the desired
position;
3. Tighten the locking bolt for table extension (34).
When sawing extra-long workpieces, the free end
of long workpieces must have something additio-
nally placed underneath it or be supported.
Clamping the workpiece (fig. H)
Workpieces must always be firmly clamped. The
workpiece clamp (21) can be placed left and right
of the workpiece. To do so:
1. Ensure the workpiece is firmly pressed against
the fence (9);
2. Insert the supplied workpiece clamp (21) into
one of the holes intended for this purpose, as
can be seen on figure H;
3. Adjust the threaded rod of the workpiece clamp
(21) to the workpiece height;
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc MS504AC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc MS504AC in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 12.98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info