Manual Vonroc MS502AC (page 10 of 92) (English, German, Dutch, French, Italian, Spanish)

764096

Zoom out

Zoom in

1/92

WWW.VONROC.COM

saw blade through a complete simulated cut to

assure there will be no interference or danger of

cutting the fence.

• Provide adequate support such as table exten-

sions, saw horses, etc. for a workpiece that is

wider or longer than the table top. Workpieces

longer or wider than the mitre saw table can tip

if not securely supported. If the cut-off piece or

workpiece tips, it can lift the lower guard or be

thrown by the spinning blade.

• Do not use another person as a substitute for

a table extension or as additional support. Un-

stable support for the workpiece can cause the

blade to bind or the workpiece to shift during the

cutting operation pulling you and the helper into

the spinning blade.

• The cut-off piece must not be jammed or pressed

by any means against the spinning saw blade. If

conﬁned, i.e. using length stops, the cut-off piece

could get wedged against the blade and thrown

violently.

• Always use a clamp or a ﬁxture designed to

properly support round material such as rods or

tubing. Rods have a tendency to roll while being

cut, causing the blade to “bite” and pull the work

with your hand into the blade.

• Let the blade reach full speed before contacting

the workpiece. This will reduce the risk of the

workpiece being thrown.

• If the workpiece or blade becomes jammed,

turn the mitre saw off. Wait for all moving parts

to stop and disconnect the plug from the power

source and/or remove the battery pack. Then

work to free the jammed material. Continued

sawing with a jammed workpiece could cause

loss of control or damage to the mitre saw.

• After ﬁnishing the cut, release the switch, hold

the saw head down and wait for the blade to stop

before removing the cut-off piece. Reaching with

your hand near the coasting blade is dangerous.

• Hold the handle ﬁrmly when making an incom-

plete cut or when releasing the switch before

the saw head is completely in the down position.

The braking action of the saw may cause the saw

head to be suddenly pulled downward, causing a

risk of injury.

• Keep your work area clean. Material mixtures

are particularly hazardous. Light metal dust may

catch ﬁre or explode.

• Do not use dull, cracked, bent or damaged saw

blades. Unsharpened or improperly set saw

blades produce narrow kerf causing excessive

friction, blade binding and kickback.

• Do not use saw blades made from high speed

steel (HSS). Such saw blades can easily break.

•

Always use saw blades with correct size and

shape (diamond versus round) of arbour holes.

Saw blades that do not match the mounting

hardware of the saw will run off-centre, causing

loss of control.

• Do not replace the integrated laser with a laser

of another type. A laser that is not compatible

with this power tool could pose a risk to persons.

• Never remove cuttings, wood chips, etc. from

the cutting area while the power tool is running.

Always guide the tool arm back to the neutral

position ﬁrst and then switch the power tool off.

• Do not touch the saw blade after working before

it has cooled. The saw blade becomes very hot

while working.

• Never make warning signs on the machine unre-

cognisable.

• If laser radiation hits your eye, you must close

your eyes and immediately turn your head away

from the beam.

• Do not use any optical instruments such as

binoculars to view the radiation source. Doing

so can damage your eye.

• Do not direct the laser beam at persons who are

looking through binoculars or similar instru-

ments. Doing so can damage their eye.

• Do not make any modiﬁcations to the laser

equipment. The setting options described in

these operating instructions can be used safely.

• Do not stand in line with the saw blade in front

of the power tool. Always stand to the side of

the saw blade. This protects your body against

possible kickback.

• Keep hands, ﬁngers and arms away from the

rotating saw blade.

• Do not reach one hand across the other when in

front of the tool arm.

• Avoid overheating of the saw teeth. When the

saw blade overheats, stop the machine. Allow

the saw blade to cool down before using the

machine again.

• Replace damaged or worn saw blades immedi-

ately.

• Only use saw blades that match the speciﬁca-

tions given in this operating manual and that

have been tested and marked in accordance

with EN 847-1.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc MS502AC in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 11,06 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Vonroc MS502AC Manual

Product: