764098

Vonroc JS501DC Manual

8
Zoom out
Zoom in
Previous page
1/28
Next page
8
EN
WWW.VONROC.COM
Switching the laser on/off (Fig. A)
• Press the laser switch (11) to switch the laser
on or off. The laser switch (11) also turns on the
LED worklight.
Adjusting the bevel angle (Fig. B, F)
1. Loosen the bolt (18), using the hex key (15).
2. Adjust the baseplate (9) to the desired position
(0°- 45°). The sawing angle (bevel) can be read
on the scale (7).
3. Tighten the bolt (7), using the hex key (15). It is
possible to store the hex key onto the machine,
as shown on Fig. B.
Adjusting the pendulum action (Fig. A)
The pendulum action switch is used to set the way
in which the teeth of the saw blade grip the material.
The pendulum action switch can be set to 4 positions:
0 - No pendulum action
1 - Small pendulum action
2 - Medium pendulum action
3 - Large pendulum action
The required pendulum action can be determined
by practical testing, although the following instruc-
tions can be observed:
• Soft material (wood, plastics etc.): set the pen-
dulum to level II or III. For a finer and cleaner
saw cut, use pendulum level 0 or I.
• Thin material, use pendulum level 0.
• Hard material (steel etc.): set the pendulum to
level 0.
• Curves: set pendulum to level 0.
Plunge cutting (Fig. H)
Plunge cutting may only be used on soft materials
such as wood, aerated concrete, gypsum plaster
boards, etc. However, this requires a certain practi-
se and is only possible with short saw blades.
1.
Place the saw onto the workpiece and switch it on.
2.
Ensure that the bottom edge of the footplate rests
on the workpiece surface as shown on Fig. H.
3. Slowly saw into the workpiece at an angle, mo-
ving the saw to a vertical position and continue
to saw along the cutting line.
4. Switch the saw off and lift off the workpiece
when the work is complete.
Optimum use
• Clamp the workpiece. Use a clamping device for
small workpieces.
• Draw a line to define the direction in which to
guide the saw blade.
• Firmly hold the machine by the grip.
• Set the sawing speed.
• Set the mitre angle.
• Switch on the machine.
• Wait until the machine has reached full speed.
• Place the saw shoe on the workpiece.
• Slowly move the machine along the pre-drawn
line, firmly pressing the saw shoe against the
workpiece.
• Do not apply too much pressure on the machi-
ne. Let the machine do the work.
• Switch off the machine and wait for the ma-
chine to come to a complete standstill before
putting the machine down.
5. MAINTENANCE
Before cleaning and maintenance, always
switch off the machine and remove the
battery pack from the machine.
Clean the machine casings regularly with a soft
cloth, preferably after each use. Make sure that the
ventilation openings are free of dust and dirt. Re-
move very persistent dirt using a soft cloth moiste-
ned with soapsuds. Do not use any solvents such
as gasoline, alcohol, ammonia, etc. Chemicals such
as these will damage the synthetic components.
ENVIRONMENT
Faulty and/or discarded electrical or
electronic apparatus have to be collected at
the appropriate recycling locations.
Only for EC countries
Do not dispose of power tools into domestic waste.
According to the European Guideline 2012/19/EC
for Waste Electrical and Electronic Equipment and its
implementation into national right, power tools that
are no longer usable must be collected separately
and disposed of in an environmentally friendly way.
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc JS501DC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc JS501DC in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info