764064

Vonroc IT501DC Manual

5
Zoom out
Zoom in
Previous page
1/28
Next page
EN
5
WWW.VONROC.COM
the use of components that are not tested and
approved by the manufacturer may result in
unforeseen damage! The device is not suitable for
commercial or industrial use.
TECHNICAL SPECIFICATIONS
Model No. IT501DC
Temperature range -40 °C + 530 °C
Accuracy
• -40 °C – 0 °C
• 0 °C – 300 °C
• 300°C – 530 °C
±3 °C
±2 °C(±2%)
±3%
Reproducibility ±1°C
Response time ≤1000ms;
Optical resolution (D:S) 12:1
Resolution 0,1 °C
Battery
2X 1.5V AAA
Permissible air humidity
0-85% RH
Permissible operating temperature
0°C-40°C
Weight (without battery)
125 g
Laser
Hazard class
Class 2 acc.
To EN60825-1: 2014;
Colour
Red
Wave length
630-660 nm
Max. output
≤ 1 mW
DESCRIPTION
The numbers in the text refer to the diagrams on
page 2-3.
Fig. A.
1. Display
2. Button [C/F]
3. Switch
4. Battery cover
5. Laser
6. Infrared sensor
Fig. B.
7. Temperature units
8. Measured value
9. Max value
10. Low battery indicator
3. ASSEMBLY
Changing the batteries
• Open the battery cover (4).
•
Connect battery. Pay attention to correct polarity!
• Close battery compartment.
4. OPERATION
WARNING! Danger of injury due to defective
components! The product must only be put
into operation if no defects are found.
Ensure that any defective parts are
replaced before the product is used again.
Check the device:
• Make sure all parts are fitted on the machine
firmly.
• Check whether there are any visible defects:
broken parts, cracks, etc.
Operation
The device measures the surface temperature of an
object. The sensor measures the emitted, reflected
and penetrated heat radiation of the object and
converts this information into a temperature value.
• Measurements of metallic or shiny surfaces
provide inaccurate measuring values.
As a repair, such surfaces can be covered with
matt adhesive tape or faint black paint.
• The laser distance meter is not able to take
measurements through transparent surfaces
such as glass.
Switch on and off (Fig. A+C)
Hold down the measure button (2) to switch on the
Equipment. Equipment will always start in the default
reference setting of single measurement mode (9).
Hold down the switch off button (4) to switch off
the equipment.
Distance and measurement field size
In order to get accurate results, the object to be
measured must be greater than the measurement
field of the device. The measured temperature is
the average temperature of the measured area. The
smaller the object, the shorter the distance must
be to the device.
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc IT501DC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc IT501DC in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 2,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info