764012
7
Zoom out
Zoom in
Previous page
1/28
Next page
EN
7
WWW.VONROC.COM
Smelting synthetics, among which matters and
foils with PVC layer;
Applying heat shrinking tubes;
Shrinkwrappers;
Thawing tubes and engines;
Repairing finishing layers: enamel of bath and
household appliances; applying epoxypowder
coverlayers;
Repairing of ski’s, surf-boards and other sports
goods;
Unscrewing too fast fixed screws and connections.
Operation (Fig. A)
You can work manually with this hot air gun or you
can put it in a vertical position.
Check if the mains switch is on position “0”
before you connect the apparatus;
Keep the main lead always away from the hot
air stream and the mouth piece;
Put the mains switch in position ‘I or II’ to let
your hot air gun operate:
“I” = 400 degrees, air flow 250 l/min.
“0” = Off
“II” = 600 degrees, air flow 500 l/min.
Switching off:
Slide the switch to 0.
Tip: If you want to get the best result, test all appli-
ances on a little part of the workpiece.
Flat rear side (Fig. C)
Inbetween usage, the machine can easily be placed
on its flat rear side (7). This prevents any hot area
from the machine getting into contact with other
surfaces
The flat rear side (7) also allows the machine to be
used in upright stationary mode.
After usage, always place the machine on its flat
rear side (7). This allows the machine to cool down
safely.
Use of accessoires (Fig. B)
Fishtail nozzle (4)
Distributes air equally over flat wide area.
Reduction nozzle (5)
Distributes air equally over small areas
Glass protection nozzle (6)
Deflects air away from glass for example when
stripping paint in window frames or softening putty.
4. MAINTENANCE
Always disconnect the apparatus before
carrying out inspection or cleaning. Never
use water or other liquids to clean the
electrical parts of the hot air gun.
Never use easy inflammable liquids for cleaning
the hot air gun, especially for the mouthpiece.
Regular maintenance of your hot air gun
prevents unnecessary problems. Keep the ven-
tilation slots of the hot air gun clean to prevent
overheating.
Troubleshooting
In case the hot air gun does not work well, we give
you subjoined some possible causes and their
solutions.
The engine gets overheated.
The ventilation slots of the hot air gun are dirty.
Clean the ventilation slots.
The hot air gun does not start when it is
switched on.
Interruption in the electrical circuit.
Check the mains lead and the mains plug.
The switch is defective.
Pull the mains lead out of the wall socket, be-
cause there is a chance of fire risk! Have the hot
air gun repaired at your local dealer.
The engine does not work, but it does heat.
Interruption in the electrical circuit.
Pull the mains lead out of the wall socket,
because there is a chance of fire risk! Have the
hot air gun repaired at your local dealer.
ENVIRONMENT
Faulty and/or discarded electrical or
electronic apparatus have to be collected at
the appropriate recycling locations.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc HA501AC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc HA501AC in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Vonroc HA501AC

Vonroc HA501AC User Manual - English, German, Dutch, French, Italian, Polish, Turkish, Spanish - 52 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info