764003

Vonroc ET503DC Manual

9
Zoom out
Zoom in
Previous page
1/56
Next page
EN
9
WWW.VONROC.COM
Before loading the tacker, make sure the
machine is in “0” position.
Never load staples and nail at the same time.
Checking the cartridge shaft
The cartridge filling level window (7) indicates the
amount of staples/nails inside the cartridge shaft.
Using the tacker
After every load test the machine on a piece
of scrape.
• Press the “0/I” switch (4) to “I” to unlock the
machine.
•
Press the “0/I” switch (4) to “0” to lock the
machine.
NOTE: When not in use, press the “0/I” switch to
“0” to lock the machine.
NOTE: Always store in Lock on “0” position.
Placing the tool
1. Place the tool on workpiece at the spot where
the staple or nail should be located.
2. Press the tool down firmly by pressing the ma-
chine on the top (5) with one hand.
3. Use your other hand to operate the switch (3).
4. By pressing the machine down firmly you lift the
safety of the machine.
Warning! The safety of the machine will be
lifted when pressure is applied to the safety
pin (6) on the bottom of the machine.
Always make sure the tacker mouth is in
direct contact with the material when
pressing the switch.
Stapling
• Press the switch (3).
The tool will cause a re bound because of
the impact it operates with. Keep this in
mind. For long nails and staples this can
cause wrong stapling or nailing. When
backpressure is applied wrong stapling or
nailing can be avoided.
4. MAINTENANCE
Make sure that the machine is not live when
carrying out maintenance work on the motor.
This machine has been designed to operate over a
long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon
proper machine care and regular cleaning.
Malfunction
Should the machine fail to function correctly, a
number of possible causes and the appropriate
solutions are given below:
In case a staple or nail is jammed in the tool, follow
the procedure below:
• Place the machine in “0” position (4).
•
Open the cartridge shaft (2) by pulling the reload
lever (1) and let the jammed nails/staples fall out.
• Reload the machine, see chapter “ Loading the
nails or staples” for instructions.
• Test the machine on a piece of scrap.
Cleaning
Regularly clean the device’s casing with a soft
cloth, preferably after each use. Keep the fan slits
free of dust and dirt. Remove tough dirt using a
soft cloth, dampened with soapy water. Do not use
solvents such as benzene, alcohol, ammonia, etc.,
which might damage the plastic parts.
ENVIRONMENT
Faulty and/or discarded electrical or
electronic apparatus have to be collected at
the appropriate recycling locations.
Only for EC countries
Do not dispose of power tools into domestic waste.
According to the European Guideline 2012/19/
EC for Waste Electrical and Electronic Equipment
and its implementation into national right, power
tools that are no longer usable must be collected
separately and disposed of in an environmentally
friendly way.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc ET503DC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc ET503DC in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 5,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info