Manual Vonroc DS502AC (page 9 of 44) (English, German, Dutch, French, Italian, Spanish)

764081

Zoom out

Zoom in

1/44

9WWW.VONROC.COM

Mounting the sanding pad:

1. Mount the sanding pad (16) onto the machine.

2. Insert the bolt into the sanding pad (16) and

insert the hex key into the bolt.

3. Whilst holding the sanding pad (16) ﬁrmly, turn

the wrench clockwise to fasten the hex bolt.

4. OPERATION

Switching on and off (Fig. A)

• To switch on the machine, move the on/off

switch (1) upwards.

• To switch off the machine, move the on/off

switch (1) downwards.

Note: It is recommended to keep the motor running

for a short period of time after sanding, so that

residual dust can be collected into the bag.

Speed adjustment (Fig. A)

The required speed can be adjusted by using the

Speed adjustment wheel (2). Also during operation

the rotational speed can be adjusted.

• To increase the speed, turn the Speed adjust-

ment knob (2) clockwise.

• To decrease the speed, turn the Speed adjust-

ment knob (2) anti-clockwise. The required

speeds depends on the material and can be

determined by practical testing.

Adjusting the telescopic tube length (Fig. C2)

1. Untighten the Connector (15) by turning it anti-

clockwise.

2. Extract or detract the Telescopic tube to the

desired length. Be aware of the warning mark

on the telescopic tube, indicating the maximum

length to ensure stability.

3. Tighten the Connector (15) by turning it clockwise.

Locking the sanding head (Fig. E)

The sanding head movement can be locked into

upwards position. This way, working comfort during

sanding of ceilings is improved.

1. Move the Sanding pad (16) to upwards position,

as shown on ﬁgure E1

2. Whilst holding the Sanding pad (16), slide the

Strap (11) over the Clip (10) as shown on ﬁgure

E2.

To unlock the sanding head movement, simply

remove the Strap (11) from the Clip (10) by sliding

it off. The sanding head can now move freely.

Hints for optimum use

• Firmly hold the machine with both hands.

• Switch on the machine.

• Place the sanding pad with sanding paper on

the workpiece.

• Slowly move the machine over the workpiece,

ﬁrmly pressing the sanding pad against the

workpiece.

• Do not apply too much pressure on the machi-

ne. Let the machine do the work.

• Switch off the machine and wait for the ma-

chine to come to a complete standstill before

putting the machine down.

5. MAINTENANCE

Always disconnect the machine from the

main power supply before carrying out any

maintenance work.

Clean the machine casings regularly with a soft

cloth, preferably after each use. Make sure that the

ventilation openings are free of dust and dirt. Re-

move very persistent dirt using a soft cloth moiste-

ned with soapsuds. Do not use any solvents such

as gasoline, alcohol, ammonia, etc. Chemicals such

as these will damage the synthetic components.

ENVIRONMENT

Faulty and/or discarded electrical or

electronic apparatus have to be collected at

the appropriate recycling locations.

Only for EC countries

Do not dispose of power tools into domestic waste.

According to the European Guideline 2012/19/

EC for Waste Electrical and Electronic Equipment

and its implementation into national right, power

tools that are no longer usable must be collected

separately and disposed of in an environmentally

friendly way.

WARRANTY

VONROC products are developed to the highest

quality standards and are guaranteed free of

defects in both materials and workmanship for the

period lawfully stipulated starting from the date of

original purchase. Should the product develop any

failure during this period due to defective material

and/or workmanship then contact VONROC directly.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc DS502AC in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 3,19 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Vonroc DS502AC Manual

Product: