764083

Vonroc DS501AC Manual

6
Zoom out
Zoom in
Previous page
1/40
Next page
6
EN
WWW.VONROC.COM
10. Sanding pad cover
11. Sanding pad
12. Sanding paper
13. Dust hose
14. Hex key holder
3. ASSEMBLY
Before assembly, always switch off the
machine and remove the mains plug from
the mains.
Mounting the side handle (Fig. A)
• The side handle (5) can be screwed into one of
the two side handle connection points (8).
Connecting the dust extraction system (Fig. A, C)
It is highly recommended to use the machine with
the dust hose and dust bag, ensuring optimal dust
extraction.
• Push the Dust hose (13) onto the Dust extracti-
on port (6) as shown on figure C.
• Make sure the dust bag is mounted to the dust
hose. The dust bag is fitted with a carrying
strap, allowing the user to carry the dust bag
whilst using the tool.
Note: The dust bag should be emptied when the
bag is half full to maintain optimal dust extraction.
Mounting and removing sanding paper (Fig. B)
• Hold the machine on its side or upside down, as
shown on Fig. B
• Mount sanding paper (12) with the required
grain size onto the sanding pad (11). Make
sure that the perforation in the sanding paper
(12) corresponds with the perforation on the
sanding pad (11).
• To remove the sanding paper (12), simply pull
the sanding paper from the sanding pad (11).
Note: Use coarse sanding paper for sanding rough,
uneven surfaces. Use medium sanding paper for
removing the remaining scratches from the coarse
sanding paper. Use fine sanding paper for finishing
surfaces.
Replacing the sanding pad (Fig. A)
Only install the sanding pad specified by the
manufacturer onto the machine.
Removing the sanding pad:
1. Remove sanding paper (12) from the sanding
pad (11).
2. Insert the supplied hex key into the bolt on the
sanding pad (11).
3.
Whilst holding the sanding pad (11) firmly, turn
the wrench anti-clockwise to loosen the hex bolt.
4. The sanding pad (11) now can be removed.
Mounting the sanding pad:
1. Mount the sanding pad (11) onto the machine.
2. Insert the bolt into the sanding pad (11) and
insert the hex key into the bolt.
3. Whilst holding the sanding pad (11) firmly, turn
the wrench clockwise to fasten the hex bolt.
4. OPERATION
Switching on and off (Fig. A)
• To switch on the machine, press the lock-on
button (3) and afterwards the on/off switch (1).
•
To switch the machine to continuous mode, keep
the on/off switch (1) pressed and simultaneously
press the lock-on button (3).
• To switch off continuous mode, press the on/off
switch (1) again.
• To switch off the machine, release the on/off
switch (1).
Note: It is recommended to keep the motor running
for a short period of time after sanding, so that
residual dust can be collected into the bag.
Speed adjustment (Fig. A)
The required speed can be adjusted by using the
Speed adjustment wheel (4). Also during operation
the rotational speed can be adjusted.
• To increase the speed, turn the Speed adjust-
ment knob (4) clockwise.
• To decrease the speed, turn the Speed adjust-
ment knob (4) anti-clockwise.
The required speeds depends on the material
and can be determined by practical testing.
Suction power adjustment (Fig. A)
The machine is fitted with a self-extracting dust
system, allowing dust to be extracted from the
working surface into the dust bag, helping to
maintain a clean and healthy working environment.
The suction power can be adjusted by turning the
Suction power adjustment wheel (7).
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc DS501AC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc DS501AC in the language / languages: English, German, Dutch, French, Polish, Turkish as an attachment in your email.

The manual is 3,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info