Manual Vonroc CT503DC (page 9 of 68) (English, German, Dutch, French, Italian, Polish, Spanish)

764073

Zoom out

Zoom in

1/68

9WWW.VONROC.COM

tool and hold the power tool motionless until the

wheel comes to a complete stop. Never attempt

to remove the cut-off wheel from the cut while the

wheel is in motion otherwise kickback may occur.

Investigate and take corrective action to eliminate

the cause of wheel pinching or snagging.

Do not restart the cutting operation in the

workpiece. Let the wheel reach full speed and

carefully re-enter the cut. The wheel may bind,

walk up or kickback if the power tool is restarted

in the workpiece.

Support panels or any oversized workpiece to

minimize the risk of wheel pinching and kick-

back. Large workpieces tend to sag under their

own weight. Supports must be placed under the

workpiece near the line of cut and near the edge

of the workpiece on both sides of the wheel.

Use extra caution when making a “pocket cut”

into existing walls or other blind areas. The prot-

ruding wheel may cut gas or water pipes, electri-

cal wiring or objects that can cause kickback.

ADDITIONAL SAFETY INSTRUCTIONS FOR

WIRE BRUSHING OPERATIONS

Safety warnings speciﬁc for wire brushing operations:

a) Be aware that wire bristles are thrown by the

brush even during ordinary operation. Do not

overstress the wires by applying excessive load

to the brush. The wire bristles can easily pene-

trate light clothing and/or skin.

b) Allow brushes to run at operating speed for at

least one minute before using them. During

this time no one is to stand in front or in line

with the brush. Loose bristles or wires will be

discharged during the run-in time.

c) Direct the discharge of the spinning wire brush

away from you. Small particles and tiny wire

fragments may be discharged at high velocity

during the use of these brushes and may beco-

me imbedded in your skin.

FOR THE CHARGER

Intended use

Charge only rechargeable battery packs. Other

types of batteries may burst causing personal

injury and damage.

The appliance is not to be used by persons (in-

cluding children) with reduced physical, sensory

or mental capabilities, or lack of experience and

knowledge, unless they have been given super-

vision or instruction

b) Children being supervised not to play with the

appliance

c) Do not recharging non-rechargeable batteries!

d) During charging, batteries must be placed in the

well ventilated area!

Integrated batteries may only be removed for

disposal by qualiﬁed personnel. Opening the

housing shell can destroy the power tool.

To remove the battery from the power tool, press

the On/Off switch (5) until the battery is fully

discharged. Unscrew the screws on the housing

and remove the housing shell in order to remove

the battery. To prevent a short circuit, disconnect

the connectors on the battery one at a time and

then isolate the poles. Even when fully dischar-

ged, the battery still contains a residual capacity,

which can be released in case of a short circuit.

Electrical safety

When using electric machines always observe the

safety regulations applicable in your country to

reduce the risk of ﬁre, electric shock and personal

injury. Read the following safety instructions.

Always check that the power supply

corresponds to the voltage on the rating plate.

Your machine is double insulated, therefore

no earthwire is required.

2. MACHINE INFORMATION

Intended use

This power tool is intended to function as a grinder,

sander, wire brush, polisher, carving or cut-off tool.

This combitool is great for editing of materials like

wood, plastic, stone, shell aluminium, brass and steel.

Always use the proper accessories and speed setting.

TECHNICAL SPECIFICATIONS

Model No. CT503DC

Rechargeable Battery 4V Li-ion 600mAh

Battery charging time 2 hours

Maximum disc diameter Ø35 mm

Maximum drill diameter Ø2.3 mm

No load speed 5000/10000/15000/min

Capacity of spring chuck 2.3 mm

Weight 0.1 kg

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc CT503DC in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 4,42 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Vonroc CT503DC Manual

Product: