778552

Vonroc CT502DC Manual

9
Zoom out
Zoom in
Previous page
1/36
Next page
EN
9
WWW.VONROC.COM
ADDITIONAL SAFETY INSTRUCTIONS FOR
WIRE BRUSHING OPERATIONS
Safety warnings specific for wire brushing operations:
a) Be aware that wire bristles are thrown by the
brush even during ordinary operation. Do not
overstress the wires by applying excessive load
to the brush. The wire bristles can easily pene-
trate light clothing and/or skin.
b) Allow brushes to run at operating speed for at
least one minute before using them. During
this time no one is to stand in front or in line
with the brush. Loose bristles or wires will be
discharged during the run-in time.
c) Direct the discharge of the spinning wire brush
away from you. Small particles and tiny wire
fragments may be discharged at high velocity
during the use of these brushes and may beco-
me imbedded in your skin.
FOR THE CHARGER
Intended use
Charge only rechargeable battery packs. Other
types of batteries may burst causing personal
injury and damage.
a)
The appliance is not to be used by persons (in-
cluding children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given super-
vision or instruction
b) Children being supervised not to play with the
appliance
c) Do not recharging non-rechargeable batteries!
d) During charging, batteries must be placed in the
well ventilated area!
e)
Integrated batteries may only be removed for
disposal by qualified personnel. Opening the
housing shell can destroy the power tool.
To remove the battery from the power tool, press
the On/Off switch (5) until the battery is fully
discharged. Unscrew the screws on the housing
and remove the housing shell in order to remove
the battery. To prevent a short circuit, disconnect
the connectors on the battery one at a time and
then isolate the poles. Even when fully dischar-
ged, the battery still contains a residual capacity,
which can be released in case of a short circuit.
Electrical safety
When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of fire, electric shock and personal
injury. Read the following safety instructions.
Always check that the power supply
corresponds to the voltage on the rating
plate.
Your machine is double insulated, therefore
no earthwire is required.
2. MACHINE INFORMATION
Intended use
This power tool is intended to function as a grinder,
sander, wire brush, polisher, carving or cut-off
tool. This combitool is great for editing of materials
like wood, plastic, stone, shell aluminium, brass
and steel. Always use the proper accessories and
speed setting.
TECHNICAL SPECIFICATIONS
Model No. CT502DC
Rechargeable Battery 8V Li-ion 900mAh
Charger CDA1111
Input of charger 100-240V~
50/60Hz 0.2A
Output of charger 9.0V d.c. 0.5A
Battery charging time 2-3hours
Maximum disc diameter Ø35 mm
No load speed 5.000–25.000/min
Capacity of spring chuck 3.2 mm
Weight 0.26 kg
Lpa (Sound pressure level) 76+3 dB(A)
Lwa (Sound power level) 87+3 dB(A)
Vibration 2.35+1.5 m/s
2
Vibration level
The vibration emission level stated in this instruc-
tion manual has been measured in accordance
with a standardised test given in EN 60745; it may
be used to compare one tool with another and as
a preliminary assessment of exposure to vibration
when using the tool for the applications mentioned.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc CT502DC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc CT502DC in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2.71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info