778553

Vonroc CT501AC Manual

6
Zoom out
Zoom in
Previous page
1/24
Next page
6
EN
WWW.VONROC.COM
2. MACHINE INFORMATION
Intended use
This power tool is intended to function as a grinder,
sander, wire brush, polisher, carving or cut-off
tool. This combitool is great for editing of materials
like wood, plastic, stone, shell aluminium, brass
and steel. Always use the proper accessories and
speed setting.
TECHNICAL SPECIFICATIONS
Model No. CT501AC
Voltage 220-240V~
Frequency 50 Hz
Power consumption 160 W
No load speed 8.000-35.000/min
Capacity of spring chuck 3.2 + 2.4 mm
Weight 1.75 kg
Lpa (Sound pressure level) 73+3 dB(A)
Lwa (Sound power level) 84+3 dB(A)
Vibration 3.74+1.5 m/s
2
Vibration level
The vibration emission level stated in this instruc-
tion manual has been measured in accordance
with a standardized test given in EN60745; it may
be used to compare one tool with another and as
a preliminary assessment of exposure to vibration
when using the tool for the applications mentioned.
• Using the tool for different applications, or with
different or poorly maintained accessories, may
significantly increase the exposure level.
• The times when the tool is switched off or when
it is running but not actually doing the job, may
significantly reduce the exposure level.
Protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work patterns.
DESCRIPTION
The numbers in the text refer to the diagrams on
pages 2 - 3
Fig. A
1. Chuck
2. Spindle lock
3. Chuck spanner
4. On/off switch
5. Speed adjustment wheel
6. Pin
7. Pin opening
8. Ring of machine
9. Inner shaft
10. Ring of flexible shaft
11. Stand
12. Workbench clamp
3. OPERATION
Before assembly always remove the plug
from the mains.
Warning! Change accessories by inserting an
accessory into the collet (or chuck) as far
possible to minimize run out and unbalance.
Assembly of accessories (Fig. A)
Press down the spindle lock (2) and hold it down.
Using the chuck spanner (3) you can undo the
chuck (1). Put the accessory in its place. Hold
down the spindle lock when you fasten the chuck
with the chuck spanner.
To mount an accessory in the flexible shaft (Fig.B)
Lock the spindle by putting the pin (6) in the pin
opening (7). Then loosen the chuck with the chuck
spanner and place the accessory. Keep the pin in
place and tighten the chuck. Make sure to remove
the pin before operating the machine.
Operation
Switch on the machine by engaging the on/off
switch (4) By adjusting the speed adjustment wheel
(5) you can regulate the speed of the Combitool. Do
not put the machine down when the motor is still
running. Do not place the machine on a dusty surfa-
ce. Dust particles may enter the mechanism.
Too high a load at a low speed of the
Combitool can burn out the engine.
MOUNTING THE FLEXIBLE SHAFT AND STAND
Flexible shaft (Fig. C)
Screw the ring (8) off the chuck and remove it.
Mount the flexible shaft on the Combitool, placing
the inner shaft (9) in the chuck. The ring of the flexible
shaft (10) can then be fastened onto the Combitool.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc CT501AC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc CT501AC in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2.15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info