763910
7
Zoom out
Zoom in
Previous page
1/56
Next page
EN
7
WWW.VONROC.COM
3. ASSEMBLY
Before any work on the power tool, remove
the battery.
The battery must be charged before first use.
Inserting the battery into the machine (Fig. B)
Ensure that the exterior of the battery is
clean and dry before connecting to the
charger or machine.
1.
Insert the battery (2) into the base of the machine
as shown in Fig. B.
2. Push the battery further forward until it clicks
into place.
Removing the battery from the machine (Fig. B)
1. Push the battery unlock button (3)
2. Pull the battery out of the machine like shown
in Fig. B.
Checking the battery charging status (Fig. C)
To check the battery charge status, push the
button (12) on battery shortly.
The battery has 3 lights indicating the charge
level, the more lights that burn, the more charge
the battery has left.
When the lights are not burning it means the bat-
tery is empty and must be charged immediately.
Charging the battery with the charger (Fig. C)
1. Take the battery (2) from the machine.
2. Turn the battery (2) to upside down position and
slide it onto the charger (14) as shown in Fig. C.
3. Push the battery until it is fully pushed into the
slot.
4.
Plug the charger plug into an electrical outlet and
wait for a while. The LED indicators on the charger
(15) will lighten up and show the charger status.
The charger has 2 LED indicators (15) which indi-
cate
the status of the charging process:
Red LED Status Green LED status Charger status
Off Off No power
Off On
Standby mode:
- No battery is
inserted or,
- Battery inserted
but charging has
finished
On Off Battery charging in
progress
Fully charging the 2Ah battery may take up to
60 minutes.
Fully charging the 4Ah battery may take up to
120 minutes.
After the battery is fully charged remove the char-
ger plug from the outlet and remove the battery
from the charger.
When the machine is not being used over a
longer period of time it is best to store the
battery in charged condition.
Fitting and removing drills or screwdriver bits (Fig. A)
The drill chuck (7) is suitable for drills and screw-
driver bits with round shaft as well as hexagonal
shaft.
1. Hold the machine firmly with one hand.
2. Open the drill chuck (7) by rotating the chuck
with your other hand in clockwise direction until
it is opened far enough for the bit to slide in.
3. Insert the shaft of the drill or screwdriver bit.
4. Tighten the drill chuck again by firmly rotating
the chuck (7) counterclockwise.
5. Check if the bit is centered well by shortly acti-
vating the machine´s on/off switch.
4. OPERATION
Adjusting the gears (Fig.A)
Never switch gears when the motor is
running, this will damage your machine.
Never put switch in the middle between both
positions, this will damage your machine.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc CD505DC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc CD505DC in the language / languages: English, German, Dutch, French, Polish, Spanish as an attachment in your email.

The manual is 6,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info