763975

Vonroc CD502DC Manual

7
Zoom out
Zoom in
Previous page
1/28
Next page
EN
7
WWW.VONROC.COM
10. On / off switch
11. Torque adjustment ring
3. OPERATION
The battery must be charged before first use.
Removing the battery from the machine (Fig. B)
• Push the battery unlock buttons (3) and pull the
battery out of the machine like shown in Fig. B.
Inserting the battery into the machine (Fig. B)
Ensure that the exterior of the battery is
clean and dry before connecting to the
charger or machine.
• Insert the battery (2) into the base of the machi-
ne as shown in Fig. B.
• Push the battery further forward until it clicks
into place.
Charging the battery with the charger (Fig. C)
• Plug the charger plug into an electrical outlet and
wait for a while. The LED indicator on the charger
(6) will lighten up and show the charger status.
LED indicator (6) (Fig. C)
The charger has 1 LED indicator (6) which indicates
the status of the charging process:
LED Charger status
Red Battery charging in progress
Green
Battery charging finished, battery fully charged
• Fully charging the 1.3Ah battery may take up to
60 minutes.
• After the battery is fully charged remove the
charger plug from the outlet and remove the
battery from the charger.
When the machine is not being used over a
longer period of time it is best to store the
battery in charged condition.
Fitting and removing drills or screwdriver bits (Fig. D)
Always remove the battery before mounting
an accessory.
The drill chuck (7) is suitable for drills and screw driver
bits with round shaft as well as hexagonal shaft.
• Hold the machine firmly with one hand
• Open the drill chuck (7) by rotating the chuck
with your other hand in clockwise direction until
it is opened far enough for the bit to slide in.
• Insert the shaft of the drill or screwdriver bit
• Tighten the drill chuck again by firmly rotating
the chuck (7) counterclockwise.
• Check if the bit is centered well by shortly acti-
vating the machine´s on/off switch.
Adjusting the gears (Fig. D)
Never switch gears when the motor is
running, this will damage your machine.
Never put switch in the middle between both
positions, this will damage your machine.
The machine has 2 drill speeds, which can be
adjusted by sliding the gear switch (8) forward
or backwards. The number on the gear switch (8)
shows which position is chosen.
• Position 1: For slow drilling, large drilling dia-
meter or screw driving. The machine has high
power at a low speed.
• Position 2: For fast drilling or small drilling
diameter
Adjusting the direction of rotation (Fig. E)
• Set the direction switch (9) to position in
order to drive screws or to use it for drilling.
• Set the direction switch (9) to position in
order to remove screws.
Switching the machine on and off (Fig. E)
The on/off switch (10) is used for activating the
machine and adjusting rotation speed.
• Pressing the on/off switch (10) will activate
the machine, the further the switch is being
pushed, the faster the drill will turn.
• Releasing the on/off switch (10) will stop the
machine.
• Move the direction reversing switch (9) to the
middle position to lock the movement of the on/
off switch.
Adjusting the torque (Fig. E)
The machine has 17 different torque settings and a
special drill mode to set the power being transmit-
ted to the chuck.
By rotating the torque adjustment ring (11), screws
can be driven to a predetermined depth, which is
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc CD502DC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc CD502DC in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info