536159

Voltcraft VC-890 Manual

55
Zoom out
Zoom in
Previous page
1/84
Next page
116
6. Appuyez plusieurs fois sur la touche SHIFT/SETUP jusqu’à ce que l’option « AUTO
BRIGTHNESS » soit sélectionnée. Un symbole en forme d’étoile * à gauche de l’option indique
que l’option est sélectionnée.
7. Appuyez sur les touches REL/PC (Log/) ou MAX/MIN (View/) pour sélectionner « ON » ou
« OFF ».
8. Le réglage « ON » signifi e que le mode économie d’énergie est activé. La luminosité de l’écran est
automatiquement réduite pendant les périodes d’inactivité.
9. Le réglage « OFF » désactive automatiquement le mode économie d’énergie.
10. Maintenez la touche SHIFT/SETUP pendant env. 2 s pour enregistrer la sélection et quitter le
menu SETUP.
23. ENTRETIEN ET NETTOYAGE
a) Généralités
Afi n de garantir la précision du multimètre pendant une période prolongée, il doit être calibré une
fois par an.
A l’exception d’un nettoyage occasionnel et d’un remplacement du fusible, l’appareil de mesure ne
nécessite aucun entretien.
Vous trouverez le chapitre concernant le remplacement de la pile et du fusible ci-après.
Contrôlez régulièrement la sécurité technique de l’appareil et des câbles de mesure
en vous assurant de l’absence de dommages au niveau du boîtier ou d’écrasements
de cordons, etc.
b) Nettoyage
Avant de procéder au nettoyage de l’appareil, tenez impérativement compte des consignes de
sécurité suivantes :
Des pièces sous tension peuvent être exposées lorsque vous ouvrez les boîtiers ou
retirez des pièces, sauf si cela peut être fait manuellement.
Avant tout entretien ou réparation, il convient de débrancher les câbles de l’objet de
mesure et de tous les objets de mesure. Éteignez le DMM.
Pour nettoyer l’appareil, n’utilisez jamais de produits contenant du carbone, d’essence, d’alcool ou
similaires. Ces produits attaquent la surface de l’appareil de mesure. En outre, les vapeurs sont
nocives pour la santé et explosives. N’utilisez jamais d’outils aux bords tranchants, de tournevis, de
brosses métalliques ou similaires pour le nettoyage.
57
Proceed as follows to insert/replace:
1. Disconnect the connected test leads from the measuring circuit and from your measuring device.
Switch off the DMM.
2. Open the housing as described in Chapter “23. Maintenance and cleaning” (page 76).
3. Replace the used battery with a new one of the same type. Insert the new battery in the battery
compartment (14) with the correct polarity. Pay attention to the polarity directions in the battery
compartment.
4. Carefully close the housing again.
b) Setting the battery type
1. Set the battery type used in the SETUP menu. This allows the device to display the battery level
correctly.
2. With the measuring device switched on, hold down the SHIFT/SETUP button (3) for approx. 2 s.
will appear on the display. You are now in SHIFT mode.
3. Hold down the SHIFT/SETUP button again for approx. 2 sec to open the SETUP menu.
4. Now press the SHIFT/SETUP button several times until the menu item “BATTERY TYPE” is
selected. An asterisk symbol * to the left of the menu item shows that the menu item is selected.
5. Press the REL/PC (Log/) or MAX/MIN (View/) buttons to select “LI-AKKU” (lithium monobloc
battery) or “ALKALINE” (alkaline monobloc battery).
6. Hold down the SHIFT/SETUP button for approx. 2 sec to save the setting and exit the SETUP
menu. You will also exit SHIFT mode.
For a suitable alkaline battery, see the following part number: Item no. 65 25 09
For a suitable lithium battery, see the following part number: Item no. 25 12 92
10. SETTING THE TIME AND DATE
1. Set the time and date in the SETUP menu.
2. With the measuring device switched on, hold down the SHIFT/SETUP button (3) for approx. 2 s.
will appear on the display. You are now in SHIFT mode.
3. Hold down the SHIFT/SETUP button again for approx. 2 sec to open the SETUP menu.
4. The menu item “SET TIME” is selected. If not, press the SHIFT/SETUP button several times to
select the menu item “SET TIME”. An asterisk symbol * to the left of the menu item “SET TIME”
shows that the menu item is selected.
… 55 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Voltcraft VC-890 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Voltcraft VC-890 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 6,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info