536159

Voltcraft VC-890 Manual

52
Zoom out
Zoom in
Previous page
1/84
Next page
54
6. PRODUCT DESCRIPTION
The measurements are indicated on a digital display on the multimeter (hereinafter called DMM). The
DMM measured value display comprises 60000 counts (count = smallest display value).
When the device is not operated for a specifi ed time (settings: 5 min., 15 min., 30 min.), it will switch
off automatically. This conserves the battery and allows a longer operating time. The Auto Power Off
function is switched off during data transmission to a PC via optical interface.
The measuring device can be used for do-it-yourself or for professional applications up to CAT IV.
The DMM can be ideally positioned with the positioning bracket on the back for improved readability.
The battery and fuse compartment can only be opened when all test leads are removed from the
measuring device. The test leads cannot be plugged into the measuring sockets when the battery and
fuse compartment is open. This increases user safety.
In the voltage and current measuring range, there is an audio warning with display indicators when
test leads are incorrectly connected. Connect the test leads correctly before measuring.
Rotary switch (4)
The individual measuring functions are selected via a
rotary switch. The automatic range selection “AUTO”
is active in some measuring functions. The appropriate
range of measurement is set for each application
individually. Always begin current measurements with
the largest measuring range (10 A) and switch to a
smaller measuring range as needed.
When the switch is in the “OFF” position, the multimeter
is turned off. Always turn the measuring device off
when it is not in use. Figure 1 shows the layout of the
measuring functions.
Fig. 1
7. DELIVERY CONTENT
• Multimeter with rubber protective frame
• 9 V alkaline monobloc battery
• 1 set of test leads
• 1 set of alligator clips
• Wire temperature sensor
• USB interface adaptor
• “VOLTSOFT” analysis software
• Operating instructions
119
e) Remplacer la pile bouton
Si la date et l’heure ne s’affi chent pas correctement, la pile bouton doit être remplacée.
Procédez comme suit pour le remplacement :
1. Débranchez les cordons de mesure connectés du circuit de mesure et de votre appareil de me-
sure. Éteignez le DMM.
2. Ouvrez le logement de la pile et du fusible comme décrit à la partie «c) Ouvrir l’appareil de
mesure» (page 117).
3. Dévissez les quatre vis du panneau arrière de l’appareil et retirez délicatement le boîtier.
4. Retirez la pile bouton du support de pile par le bas. Soulevez pour cela le support de pile légère-
ment vers le haut.
5. Remplacez la pile bouton usée par une neuve du même type (CR2032). Introduisez une nouvelle
pile bouton dans le logement. Veillez à ce que le pôle positif soit orienté vers le haut.
6. Refermez ensuite le boîtier en procédant dans l’ordre inverse et revissez le logement de la pile
et du fusible.
Vous pouvez commander une pile bouton adéquate sous le numéro de commande suivant :
n° de commande 65 01 83
… 52 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Voltcraft VC-890 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Voltcraft VC-890 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 6,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info