26
Without inserted accumulators, the standby display appears:
The lines "---" mean that there is no accumulator inserted in these slots.
The numbers 1 to 8 stand for the 8 slots in which you can insert the mono, baby, mignon or
micro accumulators. The arrangement on the display corresponds to the arrangement of the
slots.
The letter "A" corresponds to the left 9 Volt slot, the letter "B" corresponds to the right 9 Volt
slot.
If no accumulator is inserted, you can turn the POWER mode on and off with the two SELECT
buttons (UP and DOWN) and adjust the display contrast in three stages.
POWER MODE means that all eight round cells are charged with twice the current.
ATTENTION!
All inserted round cell accumulators must be fast-charge capable in POW-
ER mode.
Please note that the inserted micro accumulators have to have a minimum
nominal capacity of 700 mAh, MIGNON min. 2000 mAh and BABY accumu-
lators at least 4000 mAh in POWER MODE!
You can select the POWER mode with the two SELECT buttons (UP and DOWN) and confirm
them with the OK button.
After pressing the OK button, you can adjust the display contrast.
During charging, you cannot change the POWER mode. When pressing OK, you go straight to
the menu with the display contrast.
You can set the contrast to "LOW", "MID" and "HIGH" with the two SELECT buttons (UP and
DOWN) and confirm the entry with the OK button.
Now insert an accumulator size MONO, BABY, MIGNON or MICRO into one of the 8 slots.
Observe the correct polarity: the positive pole of the accumulator always has to point inwards
towards the charger and the negative pole outwards.
CHARGE- MANAGER 2020
====================
DISPLAY CONTRAST <>
MID
CHARGE- MANAGER 2020
====================
POWER- MODE <>
ON
1:--- CM2020 2:---
3:--- 4:---
5:--- A:--- 6:---
7:--- B:--- 8:---
27
The charger detects this accumulator and starts querying the program settings.
Now you merely need to select the charge program with the two SELECT buttons (UP and
DOWN). Five different programs are available.
These programs have the following functions:
CHA (CHARGE) means that the inserted accumulator is fast-charged.
DIS (DISCHARGE) means that the inserted accumulator is discharged only.
CHK (CHECK) means that the inserted accumulator is discharged and charged again.
CYC (CYCLE) means that the inserted accumulator is first charged, then discharged and finally
charged again.
ALV (ALIVE) means that the accumulator is charged / discharged / charged / discharged and
charged again. The ALIVE program serves to revive new accumulators and accumulators
stored over a longer period of time.
You now have five seconds to select the program. After each press of the button for changing
the charge program, you have once again 5 seconds. After these 5 seconds, the setting is tak-
en over and the program activates.
You can also press "OK" for confirmation.
Without an entry, the program CHARGE starts.
If a program was already started in slot 1,
"- ADJ SAME AS SLOT 1" appears.
This means that this accumulator is charged with the same program as the one in slot 1.
So if you want to charge several accumulators with the same program, first insert an accumu-
lator in slot 1 and select the desired program. Then insert the remaining accumulators; these
are then charged with the same program without the push of any button.
The built-in fan runs with maximum power when starting the device. With the programs CHA,
CYC and ALV, the device starts charging, with the programs DIS and CHK, it starts discharg-
ing.
CHA = Charge once only
DISCHARGE = discharge only once
CHK = Discharge / charge
CYC (CYCLE)= charge / discharge / charge
ALV = Charge - discharge - charge - discharge - charge
- ADJ CHARGE CHA
- ADJ DISCHARGE DIS
- ADJ CHECK CHK
- ADJ CYCLE CYC
- ADJ ALIVE ALV
CHARGE- MANAGER 2020
====================
SET PROGRAM SLOT 1<>
- ADJ CHARGE CHA
