738481

Voltcraft 2127443 Manual

5
Zoom out
Zoom in
Previous page
1/12
Next page
b) Additional information on lithium rechargeable batteries
• Li-Ion batteries installed in this device require special care during charging/discharging, ope-
ration and handling.
• Never destroy or damage the rechargeable battery, do not drop it or puncture it with any
objects. Protect the rechargeable battery from mechanical stress. This may cause a re or
explosion!
• Ensure that the device does not overheat during use, charging, discharging, transport and
storage. Do not place the device near heat sources and protect it from exposure to direct
sunlight. If the device overheats, there is a risk of re and explosion!
• The device must not exceed a temperature of +60 °C.
• If a device is damaged or the outer cover is puffed/swollen, discontinue use of the device. Do
not recharge it. This may cause a re or explosion!
Overview of parts
1
2
3
4
56 7
8
9
10
START
ERR
1 Button for charge level indicator and activation of LED light and power bank function
2 Charge level indicator
3 Protective cover
4 LED light
5 Micro USB charging input “Input”
6 USB charging output “Output”
7 Mechanically coded connection for starter cable
8 MOSFET housing with LED status indicator for starter operation
9 Mechanically coded plug for quick start system
10 Pole terminals (red +, black -)
Start-up and charging
• The quick start system must be fully charged before use.
• Standard USB quick chargers with a charging current of at least 1 A are suitable for char-
ging. An output charging current of at least 1.5 A is recommended because it shortens the
charging time.
• Connect the included charging adapter cable to the USB charger (not included).
• Plug the Micro USB cable into the Micro USB charging input “Input” (5).
• As soon as your USB charger provides sufcient charging current, the charging process
is indicated by the LEDs of the charge level indicator (2), which light up one after another.
• If all 4 LEDs of the charge level indicator light up at the same time or are permanently lit, the
charging process is completed.
• Remove the charging cable from the start system.
• Briey press the activation button (1) to display the current charge status.
View Meaning
4 LEDs Start system is fully charged and can be used without restriction.
3 LEDs Start system is 75% charged and can be used without restriction.
2 LEDs Start system is 50% charged. It can only be used as power bank or LED light.
1 LED Start system is 25% charged. It can only be used as power bank or LED light.
0 LED Start system is not ready for use and must be charged.
Operation
a) Start support function
The quick start system can support a weak starter battery when starting the engine. During
start-up a very high current is needed. The quick start system emits multiple high current pulses
during the start-up phase. This is usually enough to support a weak starter battery.
Never short-circuit the two pole terminals. This will discharge the quick start system
and damage the rechargeable battery.
To perform start-up, proceed as follows:
• Check the charge status of the quick start system. For a start-up support at least 3 LEDs
must light up. If fewer LEDs are lit, the quick start system must rst be charged.
• Open the protective cover (3) on the quick start system.
• Insert the starter cable plug (9) into the connection for the starter cable (7). The plug is
mechanically coded and ts together only with the correct polarity. Ensure rm and reliable
contact.
• The green LED status indicator on the MOSFET housing (8) starts to ash.
• Connect the red pole terminal (10) to the plus pole (+) and the black pole terminal (10) to
the minus pole (-) of the car battery. Ensure that the contact is connected properly. Turn the
terminals back and forth to break possible oxide layers on the poles.
• Once the contact is established, the green LED glows steadily after a few seconds and you
will hear a short beep. Start your car within 30 seconds. The quick start system now emits
multiple current pulses during the start-up phase. They should be enough to start the engine.
• When the engine starts, disconnect the quick start system and remove the starter cable from
the quick start system. Close the connections with the protective cover.
• If the engine does not start, disconnect the quick start system. Wait approx. 5 minutes and
then repeat a start-up operation.
• If the engine still does not start after three attempts, the start support process must be termi-
nated. Probably, the car battery is defective, or there is another problem. In this case, have
the vehicle checked by a specialist workshop.
LED status indicator on the MOSFET housing (8)
View Meaning
Green ashing Quick start system is ready
Green steady light with beep Start mode is activated
Red steady light Connection error. Please check all contacts
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Voltcraft 2127443 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Voltcraft 2127443 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info