519768
8
Zoom out
Zoom in
Previous page
1/13
Next page
EN-1
English
Warning Before Installation
Contact your distributor in the
event of occurrence.
Refer to your user's manual for the
operating temperature.
Power off the Network Camera as
soon as smoke or unusual odors are
detected.
Do not touch the Network Camera
during a lightning storm.
Do not place the Network Camera on
unsteady surfaces.
Do not drop the Network Camera.
Do not insert sharp or tiny objects
into the Network Camera.
EN-2
Package Contents
1
Software CD
IP7361 with an RJ45 Cable
Quick Installation Guide
Waterproof Connector (for backup
use)
Alignment Sticker / Silica Gel
Wall Mount Bracket
Sun Shield
Power Adapter
Waterproof Connector for RJ45
Ethernet Enclosure
RJ45
Warranty Card
EN-3
English
Physical Description
2
IR LED
Lens
Light Sensor
Power Cord Socket
General I/O
Terminal Block
Reset Button
Status LED
SD/SDHC Card Slot
RJ45 Cable
EN-4
1. Attach the alignment sticker to the wall. Drill four holes into the wall. Then hammer the supplied
plastic anchors into the holes and secure the plate with supplied screws.
2. Fix the
-bracket to the side of the Network Camera with two screws.
3. Feed the RJ45 cable through the front opening of the wall mount bracket. (If you want to use
external devices such as sensors and alarms, please refer to the assembling steps on the next
page.)
4. Open the lens cover.
5. Push the spring mortise and hook the bracket onto the groove of the wall mount bracket.
6. Secure the two screws on the other side of the wall mount bracket.
7. Hang the wall mount bracket on the plate.
8. Fix the wall mount bracket with the supplied screw.
9. Adjust the angle of the wall mount bracket to aim at the shooting area.
1
2
7
4
5
3
6
8
9
Hardware Installation
3
EN-5
English
Waterproof Connector
1 Power +12V
2 Digital Output
3 Digital Input
4 Ground
5 AC 24V
6 AC 24V
7 RS485 +
8 RS485 -
1 External MIC In
2 Ground
3 Audio Out
4 Ground
87654321
4321
1. Disassemble the components of the waterproof connector into part (A) ~ (E) as shown above.
2. Open the back cover of the Network Camera.
3. Remove the rubber stopper from the bottom of the Network Camera and secure the screw nut (A)
tightly.
4. If you need extra power for external devices, please feed the power cable through the wall mount
bracket and the waterproof connector (E --> D --> B --> A) as the illustration shown below. Then
connect the power cord to the socket. Note: There are 7 holes on the seal (B), and the widest hole
with a crack on the side is specic for power cord.
5. If you have external devices such as sensors and alarms, feed the cables through the wall mount
bracket and the waterproof connector (E --> D --> B --> A) as the illustration shown below. Then
refer to the pin denition to connect them to the general I/O terminal block. Note: The recom-
mended cable gauge is 2.0 ~ 2.8 mm.
6. Push the seal (B) into the housing (D).
7. Insert the seals (C) into the empty holes on the seal (B) to avoid moisture.
8. Secure the sealing nut (E) tightly.
Components of the Waterproof Connector
Seals (C)
Housing (D)
Sealing Nut (E)
Seal (B)
Screw Nut (A)
Pin Denition
Assembling Steps
3
4
(E)
(D)
(B)
(A)
5
4
7
6
8
(C)
(B)
(D)
(E)
EN-6
Cabling Assembly
4
1
2
3
4
5
6
7
8
(D)
(B)
(C)
(A)
(E)
Components of the Waterproof
Connector
Screw Nut (C)
Housing (D)
Gasket (E)
Seal (B)
Sealing Nut (A)
RJ45 Cable Dimension (unit: mm)
Prepare an Ethernet cable
and strip part of the sheath.
Insert the housing into the
screw nut.
Insert the seal into the housing.
Insert the stripped Ethernet
cable through the sealing
nut and the housing.
Clamp the cable with
an RJ45 plug.
Push the RJ45 plug into the
housing, then secure the
sealing nut tightly.
Attach the gasket to the front
of the housing.
Assembling Steps
Recommended cable gauge: 24AWG
(0.51 mm)
Connect the Ethernet cable to the RJ45 cable and secure the
connectors tightly.
RJ45 Cable Connector
EN-7
English
Network Deployment
5
Power over Ethernet (PoE)
When using a non-PoE switch
Use a PoE power injector (optional) to connect between the Network Camera and a non-PoE
switch.
When using a PoE-enabled switch
The Network Camera is PoE-compliant, allowing transmission of power and data via a single
Ethernet cable. Follow the below illustration to connect the Network Camera to a PoE-enabled
switch via Ethernet cable.
POWER
COLLISION
LINK
RECEIVE
PARTITION
1
2
3
4
5
Non-PoE Switch
PoE Power Injector
(optional)
POWER
COLLISION
LINK
RECEIVE
PARTITION
1
2
3
4
5
PoE Switch
EN-8
1. Install "Installation Wizard 2" from the Software Utility directory on the software CD.
2. The program will conduct an analysis of your network environment. After your network
is analyzed, please click on the "Next" button to continue the program.
3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network
Cameras on the same LAN.
4. After searching, the main installer window will pop up. Click on the MAC that matches
the one labeled on the side of the camera or S/N number on the label of carton to
connect the Internet Explorer to the Network Camera.
0002D17151CD
1
2
Model No.: IP7361
P/ N: 100043690G
F/W Ver.: 0100d
CARTON O F NO. 01
MADE IN TAIWAN
/
Q'ty: 1 PCS
EAN: 4712123671550
S/ N: 0002D17151C D
0002D17151CD
00-02-D1-07-25-8A 192.168.5.151 IP7361
Installation
Wizard 2
IW
2
Assigning an IP Address
6
EN-9
English
For further setup, please refer to the user's manual on the software CD.
Ready to Use
7
1. Access the Network Camera from the LAN.
2. Retrieve live video through a web browser or recording software.
3. Unscrew the zoom controller to adjust the
zoom factor. Upon completion, tighten the
zoom controller.
4. Unscrew the focus controller to adjust the
focus range. Upon completion, tighten the
focus controller.
T
W
N
3
4
EN-10
5. Tighten the lens cover.
6. Open the back cover.
7. Tear down the aluminum foil vacuum bag and take out the silica gel. Attach the silica
gel to the inner side of the back cover, then tighten the back cover. (Please replace
the silica gel with a new one if you open the back cover after installation.)
Note
If you want to use the supplied sun shield for outdoor environments, please follow the steps below to
install:
1. Tighten the supplied two screws.
2. Attach the supplied sun shield to the Network Camera and slide it to the desired position.
3. Fix the sun shield with the supplied two screws.
5
6
7
1
2
3
EN-11
English
VIVOTEK also provides other accessories for versatile applications as the following
illustrations. Please visit VIVOTEK's ofcial website for more purchase information.
35°
60°
IR illuminator (distance 30m, 60°)
Built-in 20 LED units
(distance 25m, 35°)
The 30m, 60° IR illuminator extends the coverage of the Network Camera and reduces
the halo effect around captured images.
Accessories
8
Corner Mount Bracket
Pole Mount Bracket
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vivotek IP7361 Fixed at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vivotek IP7361 Fixed in the language / languages: English as an attachment in your email.

The manual is 7,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Vivotek IP7361 Fixed

Vivotek IP7361 Fixed User Manual - English - 170 pages

Vivotek IP7361 Fixed Quick start guide - German - 13 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info