653457
5
Zoom out
Zoom in
Previous page
1/18
Next page
TIPS AND TECHNIQUES
Seals
There are two seals supplied with your blender. The seals are
interchangeable and their uses are:
During the blend - place a seal on the blade base attaching the
blade base to either container.
To travel - place a seal on the flip-top lid before attaching to the
20 ounce (0.6 L) container.
The seals are used to avoid leaks and spills. If you experience leaking:
Make sure the seal is in place on the blade assembly before
attaching to either container.
Thread the blade base onto the container and until it stops. Try to
thread a little further to make sure it is tight.
Keep the seals clean, allow to air dry between uses and keep in a safe
place to avoid losing them.
SCALE 1.000
SCALE 1.000
Seal
Flip-top Lid
Seal
Blade Base
During the Blend
To Travel
Ingredients
Cut ingredients into 1-inch pieces.
Cubed ice blends better than crushed ice.
The order to add ingredients to each container is important. Place ingredients into each container in the
order they appear in the recipe.
Do not fill the 40 ounce (1.2 L) container more than two-thirds full (approximately 28 ounces) when
blending thick texture recipes (e.g., hummus or nut butters). This allows room at the top of the container to
use the tamper, to add liquid to the blend if necessary and will reduce the chances of overheating the unit.
Remember: Always follow guidelines in the recipe to ensure the best blend quality. Operating at a lower speed
than suggested in the recipe can cause the motor to overheat. Blend for the full processing time suggested in
the recipe. The smaller blades will take a bit longer than larger Vitamix machines.
If ingredients are not flowing easily through the blades, use the tamper in the 40 ounce (1.2 L) container,
or add more liquid to the blend. DO NOT overfill.
9
CONTROL PANEL
1
2
3
1. Power Indication: When the stop symbol (O) brightens, this indicates that the machine is plugged in
and power is flowing. Unplug the machine whenever it will be left unattended.
The stop symbol on the control panel will behave in these ways:
Slow flash – machine is plugged in but the container is not properly in place on the motor base.
Solid (no flash) – machine is plugged in, the container is in place, and the machine is ready to blend.
Fast flash – error caused by one of the following:
A. The motor base is plugged in while the control knob is not in the stop position (O).
B. The container was placed on the machine while the control knob was not pointed at the stop
symbol (O).
C. The container was removed from machine while operating (could include lifting the container away
from the motor base and the interlock tabs losing contact with the base during tamping).
If the container is lifted or rocked from the motor base during blending, the machine will turn o
automatically. To continue, place the container back on the motor base. Push in on the center of the
control knob to start the blades.
2. Control Knob: Allows you to select a program or use variable speed from 1 to 10 (low to high).
To begin, rotate the control knob counterclockwise from the stop symbol to select a program or
clockwise from the stop symbol to the desired variable speed setting. Push in on the center of the knob
to activate the blades. When blending with a program, allow the blender to blend through the cycle and
stop on it’s own. When using variable speed, push in on the center of the control knob again to stop the
blades. Rotate the control knob back to the stop symbol.
3. Pulse (
): Rotate the control knob to the counterclockwise to the pulse position. Push in on the
center of the control knob to activate the blades. The machine will blend at 50% of high speed for as
long as it is held in this position.
4. Programs: Your blender is equipped with four program settings. Rotating the control knob
counterclockwise from the stop symbol allows you to select a program for Smoothies (
),
Power Blends (
), Dips and Spreads ( ) and Frozen Desserts ( ). Program blending speeds and
duration vary and will stop automatically at the end of the program. To begin a program, rotate to the icon
and then press in on the center of the control knob to activate the blades. To stop, push in again on the
center of the control knob. Rotate the control knob back to the stop symbol when done.
S55
4
8
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vitamix S 55 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vitamix S 55 in the language / languages: English, French as an attachment in your email.

The manual is 2,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Vitamix S 55

Vitamix S 55 User Manual - Dutch - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info