769323
53
Zoom out
Zoom in
Previous page
1/96
Next page
D-307500 PowerMaster 360 Installer's Guide 53
4.9.5 Testing the Broadband/PowerLink Module
1
The Broadband diagnostic procedure enables to test the communication of the Broadband Module (see section 4.6.7)
with the PowerManage server and reports the diagnostic result. In case of communication failure, detailed information
of the failure is reported.
07:DIAGNOSTICS  BROADBAND MODULE  PLEASE WAIT… Unit is OK
Notes:
1. When the button is pressed, the test result may take up to 4 min. before it is displayed.
2. If the Broadband Module is not registered to the PowerMaster 360, the menu BROADBAND MODULE will not be
displayed.
The following table presents the list of messages that may be reported:
Message
Description
Unit is ok
Broadband Module is functioning correctly.
Test aborted
The diagnostic test is aborted, as follows:
AC failure – Broadband Module is set to OFF mode.
Broadband Module has not completed the power-up procedure. In this case, the installer should
wait a maximum of 30 seconds before re-testing.
Comm. loss
The RS-232 serial interface between the Broadband Module and the PowerMaster-360 failed.
Rcvr Ip missing
Receivers IP 1 and 2 settings are missing in the PowerMaster 360.
Cable unplugged
The Ethernet cable is not connected to the Broadband Module.
Check lan config
This message appears in any of the following cases:
Incorrect Broadband Module IP has been entered.
Incorrect subnet mask has been entered.
Incorrect default gateway has been entered.
DHCP server failure.
Rcvr#1 UnReach.
Rcvr#2 UnReach.
Receiver 1 or 2 is inaccessible, as follows:
Wrong receiver IP has been entered.
Receiver failure.
WAN Network failure.
Rcvr#1 UnReg.
Rcvr#2 UnReg.
The PowerMaster-360 unit is not registered to IP receiver 1 or 2.
Timeout err.
Broadband Module does not respond to test result within 70 sec.
Invalid result
Broadband Module responds with a result code that is not recognized by the PowerMaster-360.
4.9.6 Testing the WLAN Module
The WLAN diagnostic procedure enables a test of the communication of the WLAN Module with the PowerManage
server and reports the diagnostic result. In case of communication failure, detailed information of the failure is reported.
07:DIAGNOSTICS  08: WLAN  PLEASE WAIT… Unit is OK
The following table presents the list of messages that might be reported:
Message
Description
“Please wait…”
Test in progress
0 – “Success”
WLAN is ok
1 – "Wi-Fi disabled”
Wi-Fi client is not enabled
2 – “Router disconn.”
No connection to router (no link, or wrong SSID or password)
3 – “DHCP failure”
Plink fail to gel IP from DHCP server (router)
4 – “Wrong password”
Wrong SSID or password
1
The name of the product is PowerLink3 IP Communicator
53


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Visonic Powermaster-360 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Visonic Powermaster-360 in the language / languages: English as an attachment in your email.

The manual is 2.8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info