580332

Visonic PowerMaster-10-30 G2 Version 18 Manual

63
Zoom out
Zoom in
Previous page
1/74
Next page
APPENDICES
62 D-304829 PowerMaster-10/30 G2 User's Guide
APPENDIX B. PARTITIONING
The control panel includes an optional partition feature. Partitioning is available only if your installer has enabled
the feature. Once partitioning is enabled Partitioning menus are added to the system which can be viewed on
the control panel's LCD display. Partitioning allows you to divide the system into three independently
controllable areas with different users assigned to each partition whereby each user can arm the partition to
which they are assigned.
Each user code can be assigned to a combination of up to 3 partitions and each partition can be armed or
disarmed regardless of the status of the other partitions within the system. For example, you can define the
garage as partition 1, the basement as partition 2, and the house as partition 3. Since each partition is
independent of other partitions, you can arm or disarm each partition as desired without altering the states of the
other partitions.
The system also supports a situation where an area is used by two or more partitions. For example, a reception
area which is common to two offices, each of which is assigned to a separate partition, will be armed only after
both offices (partitions) are armed. In the armed state the reception area will be disarmed after either office
(partitions) has been disarmed to allow the user of that office to use the reception area without generating an
alarm. Such an area is termed a "common area".
Note: Remote operation is performed per partition, or per user code defined for a particular partition, when
partition is enabled.
B1. Selecting a Partition
When operating in partition mode the first display will read:
P1: R P2: N P3: R
Press ; the display will read:
SELECT PARTITION
Press , and to select the desired corresponding partition.
Note: After 5 seconds of no button press there will be a timeout and the display will revert to the All Partition
display.
B2. Arming / Disarming the System
Before continuing, make sure that Partitioning has been enabled via the Installer Mode.
Arming/Disarming All Partitions
To arm/disarm all partitions in READY mode, press the / or button.
Arming/Disarming a Single Partition
To arm/disarm a single partition, press the button on the control panel and then press the Partition
number: 1; 2; or 3. Then, press the / or button.
B3. The Show Function
The show function is enabled during single/all partition(s) status and displays information that is relevant to the
selected or all partitions.
Show All Partitions
In Ready mode press , the display will show information on all partitions. Press repeatedly to
view memory / status content.
Show Single Partition
In Ready mode, press
and then press the partition number. The display will show information relevant to
the selected partition. Press repeatedly to view memory / status content.
Note: After 5 seconds of no button press there will be a timeout and the display will revert to the all partition
display.
… 63 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Visonic PowerMaster-10-30 G2 Version 18 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Visonic PowerMaster-10-30 G2 Version 18 in the language / languages: English as an attachment in your email.

The manual is 2,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Visonic PowerMaster-10-30 G2 Version 18

Visonic PowerMaster-10-30 G2 Version 18 Installation Guide - Dutch - 112 pages

Visonic PowerMaster-10-30 G2 Version 18 User Manual - Dutch - 72 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info