654957
9
Zoom out
Zoom in
Previous page
1/15
Next page
9
G
Battery life is up to 60 minutes and decreases over time. The central button on top of the robot will flash when bat-
tery level is low. Then recharging is needed. The Robot will search for and drive back to the Charging Station au-
tonomously in case of low battery during manual cleaning for 60 minutes and/or any scheduled cleaning. Whilst
searching for the Charging Station the central button on top of the robot will flash.
To maintain peak performance of the battery it is recommended to charge 12 hours before first use or when used
again after a long time.
Using the Product
Before using, pick up objects like clothing, loose papers, pull cords for blinds or curtains, power cords and any
fragile objects as they may entangle with the cleaning brushes. If the device passes over a power cord and drags
it, there is a chance an object could tumble off a table or shelf.
MANUAL CLEANING:
1. Ensure the battery is charged.
2. Place the Robot in the middle of the room.
3. To turn the Robot ON press the power switch.
4. To START the Robot, press one of the Clean Mode Buttons to choose desired cleaning mode (see section
"Cleaning Modes").
5. To PAUSE the Robot, press one of the Clean Mode Buttons.
6. To RESUME the Robot, press one of the Clean Mode Buttons again.
7. To turn the Robot OFF, press the power switch.
SYNCHRONISATION OF TIMER:
1. Before first use the Timer has to be synchronized with the robot.
2. Ensure that the robot is turned off and that the Timer is equipped with batteries.
3. Press and hold the “OK” button of the Timer whilst switching the Robot on by pressing the power switch.
4. If the robot is beeping two times the synchronisation was successful, otherwise please repeat the steps
mentioned above.
TIME SETTING OF TIMER AND ROBOT:
1. Before using scheduled cleaning the system time of the robot has to be set.
2. Ensure that the robot is turned on and that the Timer is equipped with batteries.
3. Press the “time” button on the Timer. The clock time on the display of the Timer starts blinking.
4. Press "right" and "left" button to switch between hour, minute and weekday setting. Use "up" and "down" but-
ton to adjust weekday and system time.
5. To finish and save the setting press the "time" button again. To cancel the process press the power button of
the Timer.
SCHEDULED CLEANING:
1. Ensure that the robot is turned on and that the Timer is equipped with batteries.
2. Press the “set” button on the Timer. The scheduling time on the display of the Timer will start blinking.
3. Press "right" and "left" button to switch between hour, minute and weekday setting.
4. Use "up" and "down" button to adjust the cleaning time and to switch between weekdays.
5. Press "OK" button to select and deselect the days for cleaning. If the robot should clean every day press the
"all" button to select all weekdays at once.
6. To finish and save the setting press the "set" button again. To cancel the process press the power button of
the Timer.
Example: On the screen, it’s Saturday (day 6), 9:58 am. The remote control is scheduled
that it will start cleaning autonomously each Monday (Day 1) and Wednesday (Day 3) at
10 am.
IMPORTANT:
For most efficient cleaning, keep your floors as clear as possible (e.g. temporarily re-
move wires, rugs, chairs, small objects, ...). With fewer obstacles, the Robot will clean
more effectively.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vileda VR301 Robot at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vileda VR301 Robot in the language / languages: English as an attachment in your email.

The manual is 3,88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Vileda VR301 Robot

Vileda VR301 Robot User Manual - German - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info