Manual Viking MT 4097S (page 14 of 332) (English, Danish, Polish, Swedish, Norwegian, Finnish)

667329

Zoom out

Zoom in

1/332

0478 192 9803 B - EN

A slope inclination of 10° corresponds to a

vertical height increase of 17.6 cm for a

100 cm horizontal distance.

In order to ensure an adequate oil supply

for the engine, the information in the

accompanying engine instruction manual

must be additionally observed when using

the machine on slopes.

If you cannot drive up the slope in reverse

or if you have doubts regarding safety, you

should not drive on the slope.

Starting off or stopping on a gradient must

be avoided.

Do not use the machine in places (slopes,

ditches etc.) where the ride-on mower can

tip over or slide. The danger of tipping over

or sliding increases if the ground is soft or

damp.

Slopes must be driven on in a longitudinal

direction. Driving transversely increases

the danger of tipping over.

Do not change speed or direction abruptly

when driving on slopes. Work in this type

of situation requires calm, cautious and

even operation of the ride-on mower.

Changes of direction on slopes must be

avoided. Only turn on slopes if this is

unavoidable. If possible, drive slowly and

in a large curve in the down-slope

direction.

Do not mow wet grass, particularly on

slopes, as wheel grip is reduced on wet

grass. The ride-on mower could slide and

become uncontrollable for the user.

The gearbox must never be disengaged

via the gearbox freewheel when driving on

slopes.

Special care must be taken when

operating attachments on slopes (altered

weight distribution of the machine).

Never try to stabilise the ride-on mower by

pressing on the ground with your foot.

If the wheels should start to slip or if the

vehicle becomes stuck in the up-slope

direction when driving on an incline, the

mowing blades or the attachment must be

disengaged. Then leave the slope by

driving slowly downhill in a straight line.

Pulling loads:

Particular care must be taken when pulling

loads, in order to prevent the risk of severe

or even fatal injuries due to the ride-on

mower tipping over.

Only use accessories approved by VIKING

for transporting objects. Transportation on

the ride-on mower is not permitted.

For pulling loads, use only the trailer hitch.

Loads must never be attached to the axle

housing or to another point above the

trailer hitch.

Please refer to the section "Pulling loads"

for information on pulled and coupling

loads. (Ö 11.8)

Exceeding the specified pulled load is

dangerous and may result in damage to

the machine (engine, gearbox etc.).

When transporting on slopes, the loads

must be adapted so that safe handling of

the ride-on mower (e.g. braking, change of

direction, starting off) is ensured at all

times.

Check whether loads are properly and

securely fastened. Use lashing straps for

securing loads.

Ensure balanced load distribution.

Use suitable additional weights

(accessories) if this is described in the

instruction manual for the attachment.

Do not execute tight curves. Particular

care must be taken when reversing.

Do not change speed or direction abruptly.

Stopping and parking:

The ride-on mower must only be parked on

a level surface.

Make sure that the ride-on mower has

come to a complete standstill before you

dismount.

Beware of the cutting tool

running on for several seconds

before coming to a standstill.

Before leaving the driver’s seat,

disengage the mowing blades

or the drive to the attachments, lower the

mowing deck and all attachments, set all

control levers to the neutral position,

engage the parking brake, stop the engine

and remove the ignition key.

Keep the ignition key in a place where only

authorised persons can access it.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Viking MT 4097S in the language / languages: English, Danish, Polish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 26,4 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Viking MT 4097S

Viking MT 4097S User Manual - German, Dutch, French, Italian, Portuguese, Spanish - 350 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Viking MT 4097S Manual

Product: