667318

Viking MB 756 YS Manual

49
Zoom out
Zoom in
Previous page
1/234
Next page
47
DEFRNLITESPTPLHURU EN
0478 111 9925 B - EN
11.8 Sharpening the mowing blade
If mowing results deteriorate over time,
this is usually the result of a blunt mowing
blade.
The following points must be noted when
resharpening:
● Remove the mowing blade. (Ö 11.7)
● Cool the mowing blade when
sharpening, e.g. with water. The blade
must not be allowed to display blue
colouring, as this would reduce its
cutting quality.
● Sharpen blades evenly to prevent
vibration due to imbalance.
● The cutting angle of 30° must be
observed.
● Observe the wear limits when
sharpening.
● Remove any sharpening burr.
11.9 Maintaining cables
The cables are adjusted correctly at the
factory.
The throttle cable and the blade brake
clutch cable must only be maintained by
trained personnel. VIKING recommends
VIKING specialist dealers.
After prolonged use or under certain
conditions, it can be necessary to adjust
the self-propulsion cables.
Adjusting the hydro self-
propulsion cable
MB 756.0 YS, MB 756.0 YC
Maintenance interval:
As required
Adjustment of the cable can be necessary
– if the maximum driving speed is no
longer achieved over time.
– if self-propulsion is permanently
engaged. This means that the lawn
mower automatically begins to move
when the recoil starter rope is pulled,
despite the self-propulsion lever not
being actuated.
Adjusting the cable
● 1 Push driving speed lever (1)
fully forwards.
● 2 Loosen lock nut (2), loosen
shift linking (3) by turning adjustment
nuts (4).
● 3 Adjust cable (5) using the two
nuts (6, 7).
When correctly adjusted, the cable is
tensioned slightly and pin (8) is
positioned right at the bottom of
guide (9). The machine can be pulled
back – the wheels are not blocked
during this process.
● 4 Adjust the shift linkage without play
using adjustment nuts (4), then tighten
lock nut (2) again.
Adjusting the gearshift cable
MB 756.0 GS
Maintenance interval:
As required
Adjustment of the cable is necessary
– if, following lengthy use, the individual
gears can no longer be engaged.
Adjusting the cable
● Tension cable (1) using the two
nuts (2, 3) on the underside of the
handlebar so that all three gears can be
correctly engaged.
Adjusting the self-propulsion
cable
MB 756.0 GS
Maintenance interval:
As required
Adjustment of the cable is necessary
– if, after a lengthy period of use, self-
propulsion does not engage when the
self-propulsion lever is actuated.
– if self-propulsion is permanently
engaged. This means that the lawn
mower automatically begins to move
when the recoil starter rope is pulled,
despite the self-propulsion lever not
being actuated.
Checking the cable tension:
1. Engage 3rd gear and pull the recoil
starter rope – the lawn mower is not
driven.
2. Pull the self-propulsion lever to the
handlebar and hold, pull the recoil
starter rope - the lawn mower is driven.
Risk of injury!
The prescribed tightening torque
must be observed.
Retaining washer (3) must be
replaced each time the blade is
installed.
Blade fastening screw (2) must be
renewed each time the blade is
replaced.
22
23
Risk of injury!
The self-propulsion cable must be
correctly adjusted before the
machine is operated.
24
… 49 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Viking MB 756 YS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Viking MB 756 YS in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 13,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info