667210

Viking MA 443C Manual

49
Zoom out
Zoom in
Previous page
1/290
Next page
47
DEFRNLITESPTNOSVDAELRU EN
0478 131 9922 D - EN
Cleaning position MA 443 C:
● Stand to the right of the machine to tilt it
upwards.
● Set the upper handlebar to the lowest
position (as far as the stop, the detent
lever does not engage in this position).
(Ö 9.3)
● Open the discharge flap (1) with the
right hand and hold it open.
● Hold the console with the left hand as
shown and hold the discharge flap
open. Press the detent lever (2) with the
thumb at the same time and hold.
● Hold the machine with the right hand at
the front handle and tilt it slowly
rearwards until the handlebar is in
contact with the ground as shown.
● Release the discharge flap (1) and
detent lever (2) and check that the
machine is standing securely.
Cleaning position MA 443:
● Hold the upper handlebar (3) and open
the quick-clamping devices – fold
downwards.
● Set down the upper handlebar (3)
rearwards.
● Open the discharge flap (1) and hold it
open.
● Lift up the lawn mower at the front and
place in the cleaning position as shown.
Check that the machine is stable.
Notes on cleaning:
● Clean off dirt using little water, with a
brush or with a cloth. In particular, also
clean the mowing blade. Never spray
water on motor components, seals,
bearing points or electrical components
such as batteries or switches.
● First, remove accumulated clipping
deposits using a stick.
● Remove dirt from the cooling air guide
(inlet slots) between the motor hood
and the lower housing to ensure that
the motor is adequately cooled.
● If necessary, use a special cleaner
(e.g. STIHL special cleaner).
13.3 Electric motor and wheels
The electric motor is maintenance-free.
The wheel bearings are maintenance-free.
13.4 Battery
Maintenance interval:
Before each use
Visually check that the battery is
undamaged. Batteries with identifiable
damage (e.g. cracks or escaping fluid),
must not be used.
13.5 Charger
Maintenance interval:
Before each use
Check electric cable for damage and
ensure that cooling air slots are free of dirt.
13.6 Checking blade wear
Maintenance interval:
Before each use
● Tilt the mower upwards into the
cleaning position. (Ö 13.2)
● Clean the mowing blade (1).
● Place a ruler (1) against the front blade
edge and measure permissible
grinding A.
● Measure blade width B using a slide
calliper (2).
● Check blade thickness C at 5 points at
least using a slide calliper (2). In
particular, minimum thickness must
also be ensured in the area of the blade
wings.
Wear limits:
Permissible grinding A: < 15mm
Blade width B: > 39 mm
Blade thickness C: > 1,6 mm
The blade must be replaced,
– if it is damaged (notches, cracks),
Risk of injury!
Before tipping up the mower, place
it on firm, level and flat ground. The
machine may tip over when working
on it in the cleaning position.
Always stand to the side of the
machine. Never work in front of or
behind the mower.
Risk of injury!
Blades are subjected to differing
degrees of wear depending on the
location and duration of use. If you
use the machine on sandy ground
or use it frequently under dry
conditions, the blade will be
subjected to greater loads and will
wear more quickly than the
average. A worn blade may break
off and cause serious injuries. The
instructions for blade maintenance
must therefore always be observed.
23
… 49 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Viking MA 443C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Viking MA 443C in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian as an attachment in your email.

The manual is 16,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info