667342
37
Zoom out
Zoom in
Previous page
1/502
Next page
35
DEFRNLITESPTNOSVFIDAPLSLSKHU EN
0478 670 9903 C - EN
Guide the scarifier in straight parallel
strips.
Maintain an even working speed.
Always place the scarifying unit in the
transport position before turning it
around. (Ö 7.5)
Avoid staying stationary in one place for
any duration.
In the case of heavily matted lawns,
repeat the process perpendicular to the
initial strips.
After scarifying:
Free the lawn completely of scarified
material.
Fertilise the lawn and re-seed any bare
patches that may have appeared.
Water the lawn generously.
8.2 Working area for operator
For safety reasons, the operator
must stay within the working area
behind the handlebar when starting the
engine and when the engine is running.
Always observe the safety distance
provided by the handlebar.
The scarifier must only be operated by
one person. Other persons must keep
out of the danger area. (Ö 4.)
8.3 If the scarifying unit becomes
blocked
Stop the engine immediately and
detach the spark plug socket.
Then inspect the machine, in particular
the scarifying unit, for damage and
eliminate the cause of the fault.
The machine is equipped with several
safety devices for safe operation and for
the prevention of improper use.
9.1 Safety devices
The scarifier is equipped with safety
devices which prevent inadvertent contact
with the blades and with ejected scarified
material.
These include the housing, discharge flap
and correctly installed handlebar.
9.2 Motorstop lever
The scarifier is equipped with a
motorstop device.
The engine stops when motorstop
lever (10) is released during running
operation.
10.1 Starting the engine
Check the oil and fuel levels. (Ö 7.3)
1 Press motorstop lever (1) to the
handlebar and hold.
2 Slowly pull out recoil starter rope (2)
to the point of compression resistance.
Then pull vigorously and quickly to
arm's length. Slowly return recoil starter
rope (2) so that it is rolled up again.
Repeat the procedure until the engine
starts.
Then lower the scarifying unit into the
operating position and scarify the lawn.
(Ö 7.5)
10.2 Stopping the engine
Place the scarifying unit in the
transport position. (Ö 7.5)
Release motorstop lever (1). The
engine and scarifying blades come to a
stop after a short run-down time.
7
9. Safety devices
Risk of injury!
If a safety device is found to be
defective, the machine must not be
operated. Consult a specialist
dealer; VIKING recommends
VIKING specialist dealers.
1
10. Operating the machine
Risk of injury!
Only start the engine when the
scarifying unit is in the transport
position.
Never tip the scarifier to start it.
Thanks to the fixed throttle setting,
the engine always operates at the
optimum working speed after
starting.
11
12
37


Need help? Post your question in this forum.

Forumrules
1

Forum

viking-lb-540

Reset search

  • Is there a drawing showing the removal and replacement of blades on a viking LB540.1 Submitted on 28-6-2021 at 18:11

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Viking LB 540 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Viking LB 540 in the language / languages: All languages as an attachment in your email.

The manual is 25,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info