484488
7
Zoom out
Zoom in
Previous page
1/89
Next page
PJD5126_PJD5226_PJD5226w_
PJD6223_PJD6253_PJD6353_
PJD6353s_PJD6383_PJD6383s_
PJD6553w_PJD6653w_
PJD6653ws_PJD6683w_
PJD6683ws
DLP Projector
User Guide
IMPORTANT: Please read this User Guide to obtain important information on installing
and using your product in a safe manner, as well as registering your product for future
service. Warranty information contained in this User Guide will describe your limited
coverage from ViewSonic Corporation, which is also found on our web site at http://www.
YLHZVRQLFFRPLQ(QJOLVKRULQVSHFL¿FODQJXDJHVXVLQJWKH5HJLRQDOVHOHFWLRQER[LQ
the upper right corner of our website. “Antes de operar su equipo lea cu idadosamente
las instrucciones en este manual”
Model No. VS14295/VS14551/VS14552/VS14191/VS14193
/ VS14555/VS14553/VS14195/VS14554/VS14550
i
Compliance Information
FCC Statement
This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy, and if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
 5HRULHQWRUUHORFDWHWKHUHFHLYLQJDQWHQQD
 ,QFUHDVHWKHVHSDUDWLRQEHWZHHQWKHHTXLSPHQWDQGUHFHLYHU
 &RQQHFWWKHHTXLSPHQWLQWRDQRXWOHWRQDFLUFXLWGLIIHUHQWIURPWKDWWRZKLFKWKHUHFHLYHULV
connected.
 &RQVXOWWKHGHDOHURUDQH[SHULHQFHGUDGLR79WHFKQLFLDQIRUKHOS
Warning:
<RXDUHFDXWLRQHGWKDWFKDQJHVRUPRGL¿FDWLRQVQRWH[SUHVVO\DSSURYHGE\WKH
party responsible for compliance could void your authority to operate the equipment.
For Canada
 7KLV&ODVV%GLJLWDODSSDUDWXVFRPSOLHVZLWK&DQDGLDQ,&(6
 &HWDSSDUHLOQXPpULTXHGHODFODVVH%HVWFRQIRUPHjODQRUPH10%GX&DQDGD
CE Conformity for European Countries
7KHGHYLFHFRPSOLHVZLWKWKH(0&'LUHFWLYH(&DQG/RZ9ROWDJH'LUHFWLYH
(&
Following information is only for EU-member states:
7KHPDUNLVLQFRPSOLDQFHZLWKWKH:DVWH(OHFWULFDODQG(OHFWURQLF(TXLSPHQW'LUHFWLYH
(&:(((
7KHPDUNLQGLFDWHVWKHUHTXLUHPHQW127WRGLVSRVHWKHHTXLSPHQWLQFOXGLQJDQ\VSHQWRU
discarded batteries or accumulators as unsorted municipal waste, but use the return and
collection systems available.
If the batteries, accumulators and button cells included with this equipment, display the
chemical symbol Hg, Cd, or Pb, then it means that the battery has a heavy metal content of
PRUHWKDQ0HUFXU\RUPRUHWKDQ&DGPLXPRUPRUHWKDQ/HDG
ii
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
 +HHGDOOZDUQLQJV
 )ROORZDOOLQVWUXFWLRQV
 'RQRWXVHWKLVXQLWQHDUZDWHU
 &OHDQZLWKDVRIWGU\FORWK
 'RQRWEORFNDQ\YHQWLODWLRQRSHQLQJV,QVWDOOWKHXQLWLQDFFRUGDQFHZLWKWKH
manufacturers instructions.
 'RQRWLQVWDOOQHDUDQ\KHDWVRXUFHVVXFKDVUDGLDWRUVKHDWUHJLVWHUVVWRYHVRURWKHU
GHYLFHVLQFOXGLQJDPSOL¿HUVWKDWSURGXFHKHDW
 'RQRWGHIHDWWKHVDIHW\SXUSRVHRIWKHSRODUL]HGRUJURXQGLQJW\SHSOXJ$SRODUL]HG
SOXJKDVWZREODGHVZLWKRQHZLGHUWKDQWKHRWKHU$JURXQGLQJW\SHSOXJKDVWZR
blades and a third grounding prong. The wide blade and the third prong are provided
IRU\RXUVDIHW\,IWKHSURYLGHGSOXJGRHVQRW¿WLQWR\RXURXWOHWFRQVXOWDQHOHFWULFLDQ
for replacement of the obsolete outlet.
 3URWHFWWKHSRZHUFRUGIURPEHLQJZDONHGRQRUSLQFKHGSDUWLFXODUO\DWSOXJV
&RQYHQLHQFHUHFHSWDFOHVDQGWKHSRLQWZKHUHWKH\H[LWIURPWKHXQLW%HVXUHWKDWWKH
power outlet is located near the unit so that it is easily accessible.
 2QO\XVHDWWDFKPHQWVDFFHVVRULHVVSHFL¿HGE\WKHPDQXIDFWXUHU
 8VHRQO\ZLWKWKHFDUWVWDQGWULSRGEUDFNHWRUWDEOHVSHFL¿HGE\WKH
manufacturer, or sold with the unit. When a cart is used, use caution when
PRYLQJWKHFDUWXQLWFRPELQDWLRQWRDYRLGLQMXU\IURPWLSSLQJRYHU
 8QSOXJWKLVXQLWZKHQXQXVHGIRUORQJSHULRGVRIWLPH
 5HIHUDOOVHUYLFLQJWRTXDOL¿HGVHUYLFHSHUVRQQHO6HUYLFLQJLVUHTXLUHGZKHQWKHXQLW
KDVEHHQGDPDJHGLQDQ\ZD\VXFKDVLIWKHSRZHUVXSSO\FRUGRUSOXJLVGDPDJHG
LIOLTXLGLVVSLOOHGRQWRRUREMHFWVIDOOLQWRWKHXQLWLIWKHXQLWLVH[SRVHGWRUDLQRU
moisture, or if the unit does not operate normally or has been dropped.
iii
Declaration of RoHS Compliance
7KLVSURGXFWKDVEHHQGHVLJQHGDQGPDQXIDFWXUHGLQFRPSOLDQFHZLWK'LUHFWLYH(&RIWKH
(XURSHDQ3DUOLDPHQWDQGWKH&RXQFLORQUHVWULFWLRQRIWKHXVHRIFHUWDLQKD]DUGRXVVXEVWDQFHVLQ
HOHFWULFDODQGHOHFWURQLFHTXLSPHQW5R+6'LUHFWLYHDQGLVGHHPHGWRFRPSO\ZLWKWKHPD[LPXP
FRQFHQWUDWLRQYDOXHVLVVXHGE\WKH(XURSHDQ7HFKQLFDO$GDSWDWLRQ&RPPLWWHH7$&DVVKRZQEHORZ
Substance
Proposed Maximum
Concentration
Actual Concentration
/HDG3E  
0HUFXU\+J  
Cadmium (Cd)  
+H[DYDOHQW&KURPLXP&U

)  
Polybrominated biphenyls (PBB)  
3RO\EURPLQDWHGGLSKHQ\OHWKHUV3%'(  
&HUWDLQFRPSRQHQWVRISURGXFWVDVVWDWHGDERYHDUHH[HPSWHGXQGHUWKH$QQH[RIWKH5R+6'LUHFWLYHV
as noted below:
([DPSOHVRIH[HPSWHGFRPSRQHQWVDUH
0HUFXU\LQFRPSDFWÀXRUHVFHQWODPSVQRWH[FHHGLQJPJSHUODPSDQGLQRWKHUODPSVQRW
VSHFL¿FDOO\PHQWLRQHGLQWKH$QQH[RI5R+6'LUHFWLYH
/HDGLQJODVVRIFDWKRGHUD\WXEHVHOHFWURQLFFRPSRQHQWVÀXRUHVFHQWWXEHVDQGHOHFWURQLFFHUDPLF
SDUWVHJSLH]RHOHFWURQLFGHYLFHV
/HDGLQKLJKWHPSHUDWXUHW\SHVROGHUVLHOHDGEDVHGDOOR\VFRQWDLQLQJE\ZHLJKWRUPRUHOHDG
/HDGDVDQDOORWWLQJHOHPHQWLQVWHHOFRQWDLQLQJXSWROHDGE\ZHLJKWDOXPLQLXPFRQWDLQLQJXS
WROHDGE\ZHLJKWDQGDVDFRRSHUDOOR\FRQWDLQLQJXSWROHDGE\ZHLJKW
iv
Copyright Information
Copyright© ViewSonic
®
Corporation, 2012. All rights reserved.
Macintosh and Power Macintosh are registered trademarks of Apple Inc.
Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of Microsoft
Corporation in the United States and other countries.
ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks of
ViewSonic Corporation.
VESA is a registered trademark of the Video Electronics Standards Association. DPMS and DDC are
trademarks of VESA.
PS/2, VGA and XGA are registered trademarks of International Business Machines Corporation.
Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors or omissions
contained herein; nor for incidental or consequential damages resulting from furnishing this material, or
the performance or use of this product.
In the interest of continuing product improvement, ViewSonic Corporation reserves the right to change
product specications without notice. Information in this document may change without notice.
No part of this document may be copied, reproduced, or transmitted by any means, for any purpose
without prior written permission from ViewSonic Corporation.
Product Registration
To meet your future needs, and to receive any additional product information as it becomes available,
please register your product on the Internet at: www.viewsonic.com. The ViewSonic
®
Wizard DVD-
ROM also provides an opportunity for you to print the registration form, which you may mail or fax to
ViewSonic.
For Your Records
Product Name:
Model Number:
Document Number:
Serial Number:
Purchase Date:
PJD5126_PJD5226_PJD5226w_PJD6223_PJD6253_PJD6353_PJD6353s_
PJD6383_PJD6383s_PJD6553w_PJD6653w_PJD6653ws_PJD6683w_PJD6683ws
ViewSonic DLP Projector
VS14295/VS14551/VS14552/VS14191/VS14193/ VS14555/VS14553/VS14195/
VS14554/VS14550
PJD5126/PJD5226/PJD5226w/PJD6223/PJD6253/PJD6353/PJD6353s/PJD6383/
PJD6383s/PJD6553w/PJD6653w/PJD6653ws/PJD6683w/PJD6683ws_UG_ENG
Rev. 1C 04-25-12
__________________________________________________________________
__________________________________________________________________
Product disposal at end of product life
The lamp in this product contains mercury which can be dangerous to you and the environment. Please
use care and dispose of in accordance with local, state or federal laws.
ViewSonic respects the environment and is committed to working and living green. Thank you for being
part of Smarter, Greener Computing. Please visit ViewSonic website to learn more.
USA & Canada: http://www.viewsonic.com/company/green/recycle-program/
Europe: http://www.viewsoniceurope.com/uk/kbase/article.php?id=639
Taiwan: http://recycle.epa.gov.tw/recycle/index2.aspx
1
Table of contents
Important safety
instructions .......................2
Introduction......................4
Projector features .................................4
Shipping contents................................. 5
Projector exterior view......................... 6
Controls and functions .........................7
Positioning your
projector..........................12
Choosing a location............................ 12
Projection dimensions........................13
Connection......................17
Connecting a computer or monitor .... 18
Connecting Video source devices...... 19
Operation........................22
Starting up the projector..................... 22
Using the menus.................................23
Utilizing the password function......... 24
Switching input signal........................ 27
Adjusting the projected image ...........28
Magnifying and searching for details. 29
Selecting the aspect ratio ...................30
Optimizing the image.........................32
Setting the presentation timer ............36
Hiding the image................................37
Locking control keys..........................37
Freezing the image.............................37
Operating in a high altitude
environment .......................................37
Creating your own startup screen....... 38
Controlling the projector through
a LAN environment........................... 39
Using the projector in standby mode. 45
Shutting down the projector .............. 45
Menu operation.................................. 46
Maintenance ...................56
Care of the projector.......................... 56
Lamp information.............................. 57
Troubleshooting .............63
Specifications..................64
Projector specifications...................... 64
Dimensions ........................................ 66
Ceiling mount installation ................. 66
Timing chart ...................................... 67
Copyright information...69
Appendix.........................70
IR control table.................................. 70
RJ45 response table ........................... 72
RS232 command table....................... 72
2
Important safety instructions
Your projector is designed and tested to meet the latest standards for safety of information
technology equipment. However, to ensure safe use of this product, it is important that you
follow the instructions mentioned in this manual and marked on the product.
Safety Instructions
1. Please read this manual before you operate your projector. Save it for future
reference.
2. Do not look straight at the projector lens during operation. The intense light beam
may damage your eyes.
3. Refer servicing to qualified service personnel.
4. Always open the lens shutter or remove the lens cap when the projector lamp is
on.
5. In some countries, the line voltage is NOT stable. This projector is designed to operate
safely within a mains voltage between 100 to 240 volts AC, but could fail if power
cuts or surges of ±10 volts occur. In areas where the mains voltage may fluctuate
or cut out, it is recommended that you connect your projector through a power
stabilizer, surge protector or uninterruptible power supply (UPS).
6. Do not block the projection lens with any objects when the projector is under
operation as this could cause the objects to become heated and deformed or even
cause a fire. To temporarily turn off the lamp, press BLANK on the projector or
remote control.
7. The lamp becomes extremely hot during operation. Allow the projector to cool for
approximately 45 minutes prior to removing the lamp assembly for replacement.
8. Do not operate lamps beyond the rated lamp life. Excessive operation of lamps
beyond the rated life could cause them to break on rare occasions.
9. Never replace the lamp assembly or any electronic components unless the projector is
unplugged.
10. Do not place this product on an unstable cart, stand, or table. The product may fall,
sustaining serious damage.
11. Do not attempt to disassemble this projector. There are dangerous high voltages inside
which may cause death if you should come into contact with live parts. The only user
serviceable part is the lamp which has its own removable cover.
Under no circumstances should you ever undo or remove any other covers. Refer
servicing only to suitably qualified professional service personnel.
12. Do not place this projector in any of the following environments.
- Space that is poorly ventilated or confined. Allow at least 50 cm clearance from walls
and free flow of air around the projector.
- Locations where temperatures may become excessively high, such as the inside of a
car with all windows rolled up.
- Locations where excessive humidity, dust, or cigarette smoke may contaminate optical
components, shortening the projector's life span and darkening the picture.
- Locations near fire alarms
- Locations with an ambient temperature above 40°C / 104°F
- Locations where the altitudes are higher than 3000 m (10000 feet).
3
13. Do not block the ventilation holes. If the ventilation holes are seriously obstructed,
overheating inside the projector may result in a fire.
- Do not place this projector on a blanket, bedding or any other soft surface.
- Do not cover this projector with a cloth or any other item.
- Do not place inflammables near the projector.
14. Always place the projector on a level, horizontal surface during operation.
- Do not use if tilted at an angle of more than 10 degrees left to right, nor at angle of
more than 15 degrees front to back. Using the projector when it is not fully horizontal
may cause a malfunction of, or damage to, the lamp.
15. Do not stand the projector on end vertically. Doing so may cause the projector to fall
over, causing injury or resulting in damage to the projector.
16. Do not step on the projector or place any objects upon it. Besides probable physical
damage to the projector, doing so may result in accidents and possible injury.
17. Do not place liquids near or on the projector. Liquids spilled into the projector may
cause it to fail. If the projector does become wet, disconnect it from the power
supply's wall socket and call your local service center to have the projector serviced.
18. This product is capable of displaying inverted pictures for ceiling mount installation.
Use only qualified ceiling mount kit for mounting the projector and ensure it is
securely installed.
19. When the projector is under operation, you may sense some heated air and odor from
its ventilation grill. It is a normal phenomenon and not a product defect.
20. Do not use the Security bar for transporting or installation. It should be used with a
commercially available theft prevention cable.
Safety instructions for ceiling mounting of the
projector
We want you to have a pleasant experience using your projector, so we need to bring this
safety matter to your attention to prevent damage to person and property.
If you intend to mount your projector on the ceiling, we strongly recommend that you use a
proper fitting projector ceiling mount kit and that you ensure it is securely and safely
installed.
If you use an inappropriate projector ceiling mount kit, there is a safety risk that the
projector may fall from the ceiling due to an improper attachment through the use of the
wrong gauge or length screws.
You can purchase a projector ceiling mount kit from the place you purchased your projector.
We recommends that you also purchase a separate Kensington lock compatible security
cable and attach it securely to both the Kensington lock slot on the projector and the base of
the ceiling mount bracket. This will perform the secondary role of restraining the projector
should its attachment to the mounting bracket become loose.
4
Introduction
Projector features
The projector integrates high-performance optical engine projection and a user-friendly
design to deliver high reliability and ease of use.
The projector offers the following features.
Dynamic PC and Dynamic Movie function adjusting the power consumption of the
lamp according to the brightness of the image being projected
DynamicEco Timer function decreasing the power consumption of the lamp by up to
70% when no input signal can be detected for a set period of time.
Presentation timer for better control of time during presentations
Support 3D DLP Link
Color management allowing color adjustments to your liking
Less than 1W power consumption when power saving mode is turned on
Screen Color correction allowing projection on surfaces of several predefined colors
Quick auto search speeding up the signal detecting process
Up to 10 sets of picture modes providing multiple choices for different projection
purposes
Selectable quick power off function
One-key auto-adjustment to display the best picture quality
Digital keystone correction to correct distorted images
Adjustable color balance control for data/video display
High brightness projection lamp
Ability to display 1.07 billion colors
Multi-language On-Screen Display (OSD) menus
Switchable normal and economic modes to reduce the power consumption
Component HDTV compatibility (YP
bPr)
The apparent brightness of the projected image will vary depending on the ambient
lighting conditions, selected input signal contrast/brightness settings, and is directly
proportional to projection distance.
The lamp brightness will decline over time and may vary within the lamp manufacturers
specifications. This is normal and expected behavior.
5
Shipping contents
Carefully unpack and verify that you have all of the items shown below. If any of these
items are missing, please contact your place of purchase.
Standard accessories
The supplied accessories will be suitable for your region, and may differ from those
illustrated.
Optional accessories
1. Replacement lamp
2. Soft carry case
3. VGA-Component adapter
Projector Power Cord VGA Cable
Multi-language user manual DVD Quick Start Guide
Remote Control &
Batteries
PJD5126/PJD5226/PJD5226w/
PJD6223/PJD6253/PJD6553w
PJD6553w/PJD6253/
PJD6383/PJD6383s
PJD6353/PJD6353s/PJD6383/
PJD6383s/PJD6653w/PJD6653ws/
PJD6683w/PJD6683ws
PJD5126/PJD6223/
PJD5226/PJD5226w
PJD6353/PJD6353s
PJD6653w/PJD6653ws
PJD6683w/PJD6683ws
6
Projector exterior view
1. External control panel
(See "Projector" on page 7 for
details.)
2. Lamp cover
3. Vent (heated air exhaust)
4. Quick-release button
5. Focus and Zoom ring
6. Front IR remote sensor
7. Projection lens
8. Type B USB port
9. RJ45 LAN input port
10. RS-232 control port
11. HDMI port
12. RGB signal output socket
13. RGB (PC)/Component video
(YPbPr/YCbCr) signal input
socket-1/2
14. S-Video input socket
15. Video input socket
16. Audio signal input socket
Audio signal output socket
17. Kensington anti-theft lock slot
18. AC power cord inlet
19. Rear adjuster foot
20. Quick-release foot
21. Security bar
Connects a commercially available
theft prevention cable.
Warning
THIS APPARATUS MUST BE EARTHED.
When installing the unit, incorporate a readily accessible disconnect device in the fixed wiring,
or connect the power plug to an easily accessible socket-outlet near the unit. If a fault should
occur during operation of the unit, operate the disconnect device to switch the power supply
off, or disconnect the power plug.
Front/upper side
1
2
3
4
5
6
7
1
2
3
4
5
6
7
PJD5126/PJD5226/PJD5226w/
PJD6223/PJD6253/PJD6553w
PJD6353/PJD6353s/PJD6383/PJD6383s
PJD6653w/PJD6653ws/PJD6683w
17
20
19
TYPE B
USB
COMPUTER IN 2
RS-232
MONITOR OUT
COMPUTER IN 1
S-Viseo
Video
Audio in
Audio
out
8 9 11 12
14 15 16
10
13
8
14 15 16
10
1312
18
21
PJD5126/PJD5226/PJD5226w
PJD6223/PJD6253/ PJD6353s/PJD638
3
PJD6383s/PJD6653w/PJD6653ws/PJD6553w/
Rear/lower side
PJD6683ws
PJD6683w/PJD6683ws
PJD6353/
7
Controls and functions
Projector
1. Focus ring
Adjusts the focus of the projected image.
2. Zoom ring
Adjusts the size of the image.
3. Keystone/Arrow keys ( / Up, /
Down)
Manually corrects distorted images
resulting from an angled projection.
4. Left/Blank
Hides the screen picture.
5. POWER indicator light
Lights up or flashes when the projector is
under operation.
POWER
Toggles the projector between standby
mode and on.
6. SOURCE
Displays the source selection bar.
7. Top IR remote sensor
Not available for the PJD5126/PJD5226/
PJD5226w.
8. MENU/EXIT
Turns on the On-Screen Display (OSD)
menu. Goes back to previous OSD menu,
exits and saves menu settings.
9. Right
Activates panel key lock.
When the On-Screen Display (OSD)
menu is activated, the #3, #4, and #9 keys
are used as directional arrows to select the
desired menu items and to make
adjustments.
10. LAMP indicator light
Indicates the status of the lamp. Lights up
or flashes when the lamp has developed a
problem.
11. AUTO
Automatically determines the best picture
timings for the displayed image.
12. TEMPerature indicator light
Lights up red if the projector's
temperature becomes too high.
13. MODE/ENTER
Selects an available picture setup mode.
Enacts the selected On-Screen Display
(OSD) menu item.
TEMP
LMMP
MODE
ENTER
AUTO
SOURCE
MENU
EXIT
TEMP
LMMP
MODE
ENTER
AUTO
SOURCE
MENU
EXIT
1
2
3
4
5
6
3
8
9
10
12
13
11
7
1
3
4
5
6
3
8
9
10
12
13
11
7
PJD5126/PJD5226/PJD5226w/
PJD6223/PJD6253/PJD6553w
PJD6353/PJD6353s/PJD6383/PJD6383s/
PJD6653w/PJD6653ws/PJD6683w/PJD6683ws
I
I
8
Remote control
To use the remote mouse control
keys (Page Up, Page Down, , and
), see "Using the remote mouse
control" on page 10 for details.
1. POWER
Toggles the projector between standby
mode and on.
2. Source selection keys (VGA 1/VGA
2/Video)
Selects an input source for display.
Video/
Selects Video, S-Video or HDMI
source for display.
Performs the same function as the
right mouse button when the mouse
mode is activated.
3. Source
Displays the source selection bar.
4. Keystone keys ( / )
Manually corrects distorted images
resulting from an angled projection.
5. ///
Selects the desired menu items and
makes adjustments.
6. Enter/
Enacts the selected On-Screen Display
(OSD) menu item.
Performs the same function as the left
mouse button when the mouse mode is
activated.
7. My Button
Allows user to define a short cut key
on the remote control, and the function
item is selected in OSD menu.
8. Menu
Turns on the On-Screen Display
(OSD) menu.
9. Mouse
Switches between the normal and
mouse modes.
Page Up, Page Down, , : active
after pressing Mouse. An icon appears
on the screen to indicate the activation
of the mouse mode.
1
2
3
5
8
9
4
18
19
14
20
21
22
23
24
6
10
12
16
13
17
11
15
7
4
1
2
3
5
8
9
4
25
19
14
20
21
22
23
24
6
10
16
11
17
18
15
7
4
12
I
I
PJD5126/PJD5226/PJD5226w/
PJD6223/PJD6353/PJD6353s
PJD6653w/PJD6653ws
PJD6253/PJD6383/PJD6383s/
PJD6683ws
PJD6553w/PJD6683w
9
Remote control code
The projector can be assigned to two different remote control codes, A or B. When several
adjacent projectors are in operation at the same time, switching the remote control codes
can prevent interference from other remote controls. Set the remote control code for the
projector first before changing that for the remote control.
To switch the code for the projector, select A or B in the SYSTEM SETUP: Advanced >
Remote Control Code menu.!
10. Lock
Activates or deactivates panel key lock.
11. Aspect
Selects the display aspect ratio.
12. Magnify
Displays the zoom bar that magnifies or
reduces the projected picture size.
13. Info
Displays the INFORMATION menu.
14. Freeze
Freezes the projected image.
15. Pattern
Displays embedded test pattern.
16. Blank
Hides the screen picture.
17. DynamicEco
Decreases the power consumption of the
lamp by up to 70%.
It takes some time to initiate this
function. Make sure the projector has
been turned on for more than 4
minutes.
If the projector is resumed by using the
Smart Restart feature, this function can
be executed immediately.
18. Auto Sync
Automatically determines the best picture
timings for the displayed image.
19. Exit
Goes back to previous OSD menu, exits
and saves menu settings.
20. PgUp (Page Up)/PgDn (Page Down)
Operates your display software program
(on a connected PC) which responds to
page up/down commands (like Microsoft
PowerPoint) when the mouse mode is
activated.
21. Volume keys (+, -)
Magnifies or reduces the volume level.
22.
Toggles the projector audio between on
and off.
23. Color Mode
Selects an available picture setup mode.
24. Timer
Displays the presentation timer settings
menu.
25. Laser
Emits visible laser pointer light for
presentation purposes.
Operating the Laser pointer
The Laser Pointer is a presentation aid for
professionals. It emits red colored light when
you press it and the indicator lights up red.
The laser beam is visible. It is necessary to
press and hold LASER for continuous output.
The laser pointer is not a toy. Parents should be
mindful of the dangers of laser energy and keep
this remote control out of the reach of children.
Do not look into the laser light window
or shine the laser light beam on
yourself or others. See the warning
messages on the back of the remote
control prior to using it.
10
To switch the code for the remote control, press PgUp and PgDn buttons on the remote
control together for 5 seconds or more. The initial code is set to A.
If different codes are set on the projector and remote control, there will be no response from
the remote control. When that happens, switch the code for the remote control again.
Using the remote mouse control
The capability of operating your computer with the remote control gives you more
flexibility when delivering presentations.
1. Connect the projector to your PC or notebook with a USB cable prior to using the
remote control in place of your computers mouse. See "Connecting a computer" on
page 18 for details.
2. Set the input signal to D-Sub / Comp. 1, D-Sub / Comp. 2 or HDMI.
3. Press Mouse on the remote control to switch from the normal mode to the mouse
mode. An icon appears on the screen to indicate the activation of the mouse mode.
4. Perform the desired mouse controls on your remote control.
To move the cursor on the screen, press / / / .
To left-click, press .
To right-click, press .
To operate your display software program (on a connected PC) which responds to
page up/down commands (like Microsoft PowerPoint), press PgUp/PgDn.
To return to the normal mode, press Mouse again or other keys except for the
mouse related multi-function keys.
Remote control effective range
Infra-Red (IR) remote control sensors are located on the front and the top of the projector.
The remote control must be held at an angle within 30 degrees perpendicular to the
projector's IR remote control sensors to function correctly. The distance between the remote
control and the sensors should not exceed 8 meters (~ 26 feet).
Make sure that there are no obstacles between the remote control and the IR sensors on the
projector that might obstruct the infra-red beam.
Operating the projector from the
front
A
pp
r
ox
.
15
°
Ap
p
r
o
x
.
+
1
5
°
Operating the projector from the
top
11
Replacing the remote control batteries
1. To open the battery cover, turn the remote control over to view its back, push on the
finger grip on the cover and slide it in the direction of the arrow as illustrated. The
cover will slide off.
2. Remove any existing batteries (if necessary) and install two AAA batteries observing
the battery polarities as indicated in the base of the battery compartment. Positive (+)
goes to positive and negative (-) goes to negative.
3. Refit the cover by aligning it with the base and sliding it back down into position.
Stop when it clicks into place.
Avoid leaving the remote control and batteries in an excessive heat or humid environment
like the kitchen, bathroom, sauna, sunroom or in a closed car.
Replace only with the same or equivalent type recommended by the battery manufacturer.
Dispose of the used batteries according to the manufacturer's instructions and local
environment regulations for your region.
Never throw the batteries into a fire. There may be danger of an explosion.
If the batteries are dead or if you will not be using the remote control for an extended
period of time, remove the batteries to avoid damage to the remote control from possible
battery leakage.
12
Positioning your projector
Choosing a location
Your room layout or personal preference will dictate which installation location you select.
Take into consideration the size and position of your screen, the location of a suitable power
outlet, as well as the location and distance between the projector and the rest of your
equipment.
Your projector is designed to be installed in one of four possible installation locations:
1. Front Table
Select this location with the projector placed near
the floor in front of the screen. This is the most
common way to position the projector for quick
setup and portability.
2. Front Ceiling
Select this location with the projector suspended
upside-down from the ceiling in front of the
screen.
Purchase the projector ceiling mount kit from your
dealer to mount your projector on the ceiling.
Set Front Ceiling in the SYSTEM SETUP:
Basic > Projector Position menu after you turn
the projector on.
3. Rear Ceiling
Select this location with the projector suspended
upside-down from the ceiling behind the screen.
Note that a special rear projection screen and the
projector ceiling mounting kit are required for this
installation location.
Set Rear Ceiling in the SYSTEM SETUP: Basic
> Projector Position menu after you turn the
projector on.
4. Rear Table
Select this location with the projector placed near
the floor behind the screen.
Note that a special rear projection screen is
required.
Set Rear Table in the SYSTEM SETUP: Basic >
Projector Position menu after you turn the
projector on.
13
Projection dimensions
Refer to "Dimensions" on page 66 for the center of lens dimensions of this projector before
calculating the appropriate position.
The "screen" mentioned below refers to the projection screen usually consisting of a surface
and a support structure
PJD5126/PJD5226/PJD6223/PJD6253/PJD6353/
PJD6353s/PJD6383/PJD6383s
PJD5126/PJD5226/PJD6223
(a) Screen
Size
[inch (m)]
4:3 image on a 4:3 Screen 16:9 image on a 4:3 Screen
(b) Projection
distance [m (inch)]
(c) Image
height
[cm (inch)]
(d) Vertical
offset
[cm (inch)]
(b) Projection distance
[m (inch)]
(c) Image
height
[cm (inch)
(d) Vertical
offset
[cm (inch)]
min. max. min. max.
30 (0.8) 1.1 (45) 1.3 (49) 46 (18) 2 (0.9) 1.1 (45) 1.3 (49 34 (14) 8.0 (3.2)
40 (1.0) 1.5 (60) 1.7 (66) 61 (24) 3 (1.2) 1.5 (60) 1.7 (66) 46 (18) 10.7 (4.2)
50 (1.3) 1.9 (75) 2.1 (82) 76 (30) 4 (1.5) 1.9 (75) 2.1 (82) 57 (23) 13.3 (5.3)
60 (1.5) 2.3 (90) 2.5 (99) 91 (36) 5 (1.8) 2.3 (90) 2.5 (99) 69 (27) 16.0 (6.3)
70 (1.8) 2.7 (105) 2.9 (115) 107 (42) 5 (2.1) 2.7 (105) 2.9 (115) 80 (32) 18.7 (7.4)
80 (2.0) 3.0 (120) 3.4 (132) 122 (48) 6 (2.4) 3.0 (120) 3.4 (132) 91 (36) 21.3 (8.4)
90 (2.3) 3.4 (135) 3.8 (148) 137 (54) 7 (2.7) 3.4 (135) 3.8 (148) 103 (41) 24.0 (9.5)
100 (2.5) 3.8 (150) 4.2 (165) 152 (60) 8 (3.0) 3.8 (150) 4.2 (165) 114 (45) 26.7 (10.5)
120 (3.0) 4.6 (180) 5.0 (198) 183 (72) 9 (3.6) 4.6 (180) 5.0 (198) 137 (54) 32.0 (12.6)
150 (3.8) 5.7 (225) 6.3 (247) 229 (90) 11 (4.5) 5.7 (225) 6.3 (247) 171 (68) 40.0 (15.8)
200 (5.1) 7.6 (300) 8.4 (330) 305 (120) 15 (6.0) 7.6 (300) 8.4 (330) 229 (90) 53.3 (21.0)
250 (6.4) 9.51 (375) 10.5 (412) 381 (150) 19 (7.5) 9.51 (375) 10.5 (412) 286 (113) 66.7 (26.3)
300 (7.6) 11.4 (450) 12.6 (495) 457 (180) 23 (9.0) 11.4 (450) 12.6 (495) 343 (135) 80.0 (31.5)
(a)
(c)
(b)
(e)
(f)
(d)
(a)
(d)
(b)
(e)
(f)
(c)
(a)
(d)
(c)
(b)
(e)
(f)
(a)
(c)
(b)
(e)
(f)
(d)
(f): Center of lens(e): Screen
4:3 image on a 4:3 screen
16:9 image on a 4:3 screen
14
PJD6253
PJD6353/PJD6353s/PJD6383/PJD6383s
(a) Screen
Size
[inch (m)]
4:3 image on a 4:3 Screen 16:9 image on a 4:3 Screen
(b) Projection
distance [m (inch)]
(c) Image
height
[cm (inch)]
(d) Vertical
offset
[cm (inch)]
(b) Projection distance
[m (inch)]
(c) Image
height
[cm (inch)
(d) Vertical
offset
[cm (inch)]
min. max. min. max.
30 (0.8) 0.9 (36) 1.2 (47) 46 (18) 3 (1.4) 0.9 (36) 1.2 (47) 34 (14) 9.1 (3.6)
40 (1.0) 1.2 (48) 1.6 (63) 61 (24) 5 (1.8) 1.2 (48) 1.6 (63) 46 (18) 12.2 (4.8)
50 (1.3) 1.5 (61) 2.0 (79) 76 (30) 6 (2.3) 1.5 (61) 2.0 (79) 57 (23) 15.2 (6.0)
60 (1.5) 1.8 (73) 2.4 (94) 91 (36) 7 (2.7) 1.8 (73) 2.4 (94) 69 (27) 18.3 (7.2)
70 (1.8) 2.2 (85) 2.8 (110) 107 (42) 8 (3.2) 2.2 (85) 2.8 (110) 80 (32) 21.3 (8.4)
80 (2.0) 2.5 (97) 3.2 (126) 122 (48) 9 (3.6) 2.5 (97) 3.2 (126) 91 (36) 24.4 (9.6)
90 (2.3) 2.8 (109) 3.6 (142) 137 (54) 10 (4.1) 2.8 (109) 3.6 (142) 103 (41) 27.4 (10.8)
100 (2.5) 3.1 (121) 4.0 (157) 152 (60) 11 (4.5) 3.1 (121) 4.0 (157) 114 (45) 30.5 (12.0)
120 (3.0) 3.7 (145) 4.8 (189) 183 (72) 14 (5.4) 3.7 (145) 4.8 (189) 137 (54) 36.6 (14.4)
150 (3.8) 4.6 (182) 6.0 (236) 229 (90) 17 (6.8) 4.6 (182) 6.0 (236) 171 (68) 45.7 (18.0)
200 (5.1) 6.2 (242) 8.0 (315) 305 (120) 23 (9.0) 6.2 (242) 8.0 (315) 229 (90) 61.0 (24.0)
250 (6.4) 7.7 (303) 10.0 (394) 381 (150) 29 (11.3) 7.7 (303) 10.0 (394) 286 (113) 76.2 (30.0)
300 (7.6) 9.2 (363) 12.0 (472) 457 (180) 34 (13.5) 9.2 (363) 12.0 (472) 343 (135) 91.4 (36.0)
(a) Screen
Size
[inch (m)]
4:3 image on a 4:3 Screen 16:9 image on a 4:3 Screen
(b) Projection
distance [m (inch)]
(c) Image
height
[cm (inch)]
(d) Vertical
offset
[cm (inch)]
(b) Projection
distance [m (inch)]
(c) Image
height
[cm (inch)
(d) Vertical
offset
[cm (inch)]
30 (0.8) 0.4 (15) 46 (18) 7 (2.7) 0.4 (15) 34 (14) 12.6 (5.0)
40 (1.0) 0.5 (19) 61 (24) 9 (3.6) 0.5 (19) 46 (18) 16.8 (6.6)
50 (1.3) 0.6 (24) 76 (30) 11 (4.5) 0.6 (24) 57 (23) 21.0 (8.3)
60 (1.5) 0.7 (29) 91 (36) 14 (5.4) 0.7 (29) 69 (27) 25.1 (9.9)
70 (1.8) 0.9 (34) 107 (42) 16 (6.3) 0.9 (34) 80 (32) 29.3 (11.6)
80 (2.0) 1.0 (39) 122 (48) 18 (7.2) 1.0 (39) 91 (36) 33.5 (13.2)
90 (2.3) 1.1 (44) 137 (54) 21 (8.1) 1.1 (44) 103 (41) 37.7 (14.9)
100 (2.5) 1.2 (49) 152 (60) 23 (9.0) 1.2 (49) 114 (45) 41.9 (16.5)
120 (3.0) 1.5 (58) 183 (72) 27 (10.8) 1.5 (58) 137 (54) 50.3 (19.8)
150 (3.8) 1.9 (73) 229 (90) 34 (13.5) 1.9 (73) 171 (68) 62.9 (24.8)
200 (5.1) 2.5 (97) 305 (120) 46 (18.0) 2.5 (97) 229 (90) 83.8 (33.0)
250 (6.4) 3.1 (122) 381 (150) 57 (22.5) 3.1 (122) 286 (113) 104.8 (41.3)
300 (7.6) 3.7 (146) 457 (180) 69 (27.0) 3.7 (146) 343 (135) 125.7 (49.5)
15
PJD5226w/PJD6553w/PJD6653w/PJD6653ws/
PJD5226w
(a) Screen
Size
[inch (m)]
16:10 image on a 16:10 Screen 16:10 image on a 4:3 Screen
(b) Projection distance
[m (inch)]
(c) Image
height
[cm (inch)]
(d) Vertical
offset
[cm (inch)]
(b) Projection distance
[m (inch)]
(c) Image
height
[cm (inch)
(d) Vertical
offset
[cm (inch)]
min. max. min. max.
30 (0.8) 0.97 (38) 1.06 (42) 40 (16) 0 (0.0) 0.91 (36) 1.00 (40) 38 (15) 3.8 (1.5)
40 (1.0) 1.29 (51) 1.42 (56) 54 (21) 0 (0.0) 1.22 (48) 1.34 (53) 51 (20) 5.1 (2.0)
50 (1.3) 1.61 (64) 1.77 (70) 67 (26) 0 (0.0) 1.52 (60) 1.67 (66) 64 (25) 6.4 (2.5)
60 (1.5) 1.94 (76) 2.13 (84) 81 (32) 0 (0.0) 1.83 (72) 2.01 (79) 76 (30) 7.6 (3.0)
70 (1.8) 2.26 (89) 2.48 (98) 94 (37) 0 (0.0) 2.13 (84) 2.34 (92) 89 (35) 8.9 (3.5)
80 (2.0) 2.58 (102) 2.84 (112) 108 (42) 0 (0.0) 2.43 (96) 2.68 (105) 102 (40) 10.2 (4.5)
90 (2.3) 2.90 (114) 3.19 (126) 121 (48) 0 (0.0) 2.74 (108) 3.01 (119) 114 (45) 11.4 (4.5)
100 (2.5) 3.23 (127) 3.55 (140) 135 (53) 0 (0.0) 3.04 (120) 3.35 (132) 127 (50) 12.7 (5.0)
120 (3.0) 3.87 (152) 4.26 (168) 162 (64) 0 (0.0) 3.65 (144) 4.02 (158) 152 (60) 15.2 (6.0)
150 (3.8) 4.84 (191) 5.32 (210) 202 (79) 0 (0.0) 4.56 (180) 5.02 (198) 191 (75) 19.1 (7.5)
200 (5.1) 6.45 (254) 7.10 (279) 269 (106) 0 (0.0) 6.09 (240) 6.70 (264) 254 (100) 25.4 (10.0)
250 (6.4) 8.06 (318) 8.87 (349) 337 (132) 0 (0.0) 7.61 (300) 8.37 (329) 318 (125) 31.8 (12.5)
300 (7.6) 9.68 (381) 10.65 (419) 404 (159) 0 (0.0) 9.13 (359) 10.04 (395) 381 (150) 38.1 (15.0)
(a)
(c)
(b)
(e)
(f)
(d)
(a)
(c)
(b)
(e)
(f)
(d)
(a)
(c)
(b)
(e)
(f)
(d)
(f): Center of lens(e): Screen
16:10 image on a 16:10 screen
16:10 image on a 4:3 screen
(a)
(d)
(c)
(b)
(e)
(f)
PJD6683w/PJD6683ws/
16
PJD6553w
PJD6653w/PJD6653ws/PJD6683w/PJD6683ws
There is 3% tolerance among these numbers due to optical component variations. It is
recommended that if you intend to permanently install the projector, you should physically
test the projection size and distance using the actual projector in situ before you permanently
install it, so as to make allowance for this projector's optical characteristics. This will help you
determine the exact mounting position so that it best suits your installation location.
(a) Screen
Size
[inch (m)]
16:10 image on a 16:10 Screen 16:10 image on a 4:3 Screen
(b) Projection distance
[m (inch)]
(c) Image
height
[cm (inch)]
(d) Vertical
offset
[cm (inch)]
(b) Projection distance
[m (inch)]
(c) Image
height
[cm (inch)
(d) Vertical
offset
[cm (inch)]
min. max. min. max.
30 (0.8) 0.78 (31) 1.02 (40) 40 (16) 1 (0.4) 0.74 (36) 0.96 (38) 38 (15) 3.8 (1.5)
40 (1.0) 1.05 (41) 1.36 (54) 54 (21) 1 (0.5) 0.99 (48) 1.28 (50) 51 (20) 5.1 (2.0)
50 (1.3) 1.31 (51) 1.70 (67) 67 (26) 2 (0.7) 1.23 (61) 1.60 (63) 64 (25) 6.4 (2.5)
60 (1.5) 1.57 (62) 2.04 (80) 81 (32) 2 (0.8) 1.48 (73) 1.92 (76) 76 (30) 7.6 (3.0)
70 (1.8) 1.83 (72) 2.38 (94) 94 (37) 2 (0.9) 1.73 (85) 2.24 (88) 89 (35) 8.9 (3.5)
80 (2.0) 2.09 (82) 2.72 (107) 108 (42) 3 (1.1) 1.97 (97) 2.57 (101) 102 (40) 10.2 (4.5)
90 (2.3) 2.35 (93) 3.06 (120) 121 (48) 3 (1.2) 2.22 (109) 2.89 (114) 114 (45) 11.4 (4.5)
100 (2.5) 2.61 (103) 3.40 (134) 135 (53) 3 (1.3) 2.47 (121) 3.21 (126) 127 (50) 12.7 (5.0)
120 (3.0) 3.14 (124) 4.08 (161) 162 (64) 4 (1.6) 2.96 (145) 3.85 (151) 152 (60) 15.2 (6.0)
150 (3.8) 3.92 (154) 5.10 (201) 202 (79) 5 (2.0) 3.70 (182) 4.81 (189) 191 (75) 19.1 (7.5)
200 (5.1) 5.23 (206) 6.80 (268) 269 (106) 7 (2.6) 4.93 (242) 6.41 (252) 254 (100) 25.4 (10.0)
250 (6.4) 6.54 (257) 8.50 (335) 337 (132) 8 (3.3) 6.17 (303) 8.02 (316) 318 (125) 31.8 (12.5)
300 (7.6) 7.84 (309) 10.20 (401) 404 (159) 10 (4.0) 7.40 (363) 9.62 (379) 381 (150) 38.1 (15.0)
(a) Screen
Size
[inch (m)]
16:10 image on a 16:10 Screen 16:10 image on a 4:3 Screen
(b) Projection
distance [m (inch)]
(c) Image
height
[cm (inch)]
(d) Vertical
offset
[cm (inch)]
(b) Projection
distance [m (inch)]
(c) Image
height
[cm (inch)
(d) Vertical
offset
[cm (inch)]
30 (0.8) 0.32 (12) 40 (16) 2 (0.8) 0.30 (12) 38 (15) 3.8 (1.5)
40 (1.0) 0.42 (17) 54 (21) 3 (1.1) 0.40 (16) 51 (20) 5.1 (2.0)
50 (1.3) 0.53 (21) 67 (26) 3 (1.3) 0.50 (20) 64 (25) 6.4 (2.5)
60 (1.5) 0.63 (25) 81 (32) 4 (1.6) 0.60 (23) 76 (30) 7.6 (3.0)
70 (1.8) 0.74 (29) 94 (37) 5 (1.9) 0.70 (27) 89 (35) 8.9 (3.5)
80 (2.0) 0.84 (33) 108 (42) 5 (2.1) 0.79 (31) 102 (40) 10.2 (4.0)
90 (2.3) 0.95 (37) 121 (48) 6 (2.4) 0.89 (35) 114 (45) 11.4 (4.5)
100 (2.5) 1.05 (41) 135 (53) 7 (2.6) 0.99 (39) 127 (50) 12.7 (5.0)
120 (3.0) 1.26 (50) 162 (64) 8 (3.2) 1.19 (47) 152 (60) 15.2 (6.0)
150 (3.8) 1.58 (62) 202 (79) 10 (4.0) 1.49 (59) 191 (75) 19.1 (7.5)
200 (5.1) 2.11 (83) 269 (106) 13 (5.3) 1.99 (78) 254 (100) 25.4 (10.0)
250 (6.4) 2.63 (104) 337 (132) 17 (6.6) 2.48 (98) 318 (125) 31.8 (12.5)
300 (7.6) 3.16 (124) 404 (159) 20 (7.9) 2.98 (117) 381 (150) 38.1 (15.0)
17
Connection
When connecting a signal source to the projector, be sure to:
1. Turn all equipment off before making any connections.
2. Use the correct signal cables for each source.
3. Ensure the cables are firmly inserted.
In the connections shown below, some cables may not be included with the projector (see
"Shipping contents" on page 5). They are commercially available from electronics stores.
The connection illustrations below are for reference only. The rear connecting jacks
available on the projector vary with each projector model.
For detailed connection methods, see pages 18-21.
1. VGA cable
2. VGA to DVI-A cable
3. USB cable
4. Component Video to VGA (D-Sub)
adapter cable
5. S-Video cable
6. Video cable
7. Audio cable
8. HDMI cable
TYPE B
USB
LAN
COMPUTER IN 2
RS-232
HDMI
MONITOR OUT
COMPUTER IN 1
2
S-Viseo
Video
Audio in
1
Audio
out
TYPE B
USB
COMPUTER IN 2
RS-232
MONITOR OUT
COMPUTER IN 1
S-Viseo
Video
Audio in
Audio
out
5
7
7
7
48
1
6
3
1
2
Notebook or
desktop computer
Speakers
or
A/V device
Monitor
(DVI)
(VGA)
PJD6223/PJD6253/
PJD6353/PJD6353s/
PJD6553w/PJD6653w/
PJD6683ws
PJD5126/PJD5226/
PJD5226w
PJD6383/PJD6383s/
PJD6653ws/PJD6683w/
18
Connecting a computer or monitor
Connecting a computer
The projector provides two VGA input sockets that allow you to connect them to both
IBM® compatibles and Macintosh® computers. A Mac adapter is needed if you are
connecting legacy version Macintosh computers.
To connect the projector to a notebook or desktop computer:
1. Take the supplied VGA cable and connect one end to the D-Sub output socket of the
computer.
2. Connect the other end of the VGA cable to the COMPUTER IN 1 or COMPUTER
IN 2 signal input socket on the projector.
3. If you wish to use the remote paging function, take a USB cable and connect the
larger end to the USB port of the computer, and smaller end to the Type B USB socket
on the projector. See "Using the remote mouse control" on page 10 for details.
Many notebooks do not turn on their external video ports when connected to a projector.
Usually a key combo like FN + F3 or CRT/LCD key turns the external display on/off. Locate a
function key labeled CRT/LCD or a function key with a monitor symbol on the notebook. Press
FN and the labeled function key simultaneously. Refer to your notebook's documentation to
find your notebook's key combination.
Connecting a monitor
If you want to view your presentation close-up on a monitor as well as on the screen, you
can connect the MONITOR OUT signal output socket on the projector to an external
monitor with a VGA cable following the instructions below:
To connect the projector to a monitor:
1. Connect the projector to a computer as described in "Connecting a computer" on page
18.
2. Take a suitable VGA cable (only one supplied) and connect one end of the cable to the
D-Sub input socket of the video monitor.
Or if your monitor is equipped with a DVI input socket, take a VGA to DVI-A cable
and connect the DVI end of the cable to the DVI input socket of the video monitor.
3. Connect the other end of the cable to the MONITOR OUT socket on the projector.
For the PJD5126/PJD5226/PJD5226w, the MONITOR OUT output only works when
COMPUTER IN 1 is made to the projector.
For the PJD6223/PJD6253/PJD6353/PJD6353s/PJD6383/PJD6383sPJD6553w/PJD6653w/
COMPUTER IN 1 or COMPUTER IN 2 is made to
the projector.
To use this connection method when the projector is in standby mode, turn on the Active
VGA Out function under the SYSTEM SETUP: Advanced > Standby Settings menu.
PJD6653ws/PJD6683w/PJD6683ws,
MONITOR OUT output only works when
19
Connecting Video source devices
You can connect your projector to various Video source devices that provide any one of the
following output sockets:
HDMI
Component Video
•S-Video
Video (composite)
You need only connect the projector to a Video source device using just one of the above
connecting methods, however each provides a different level of video quality. The method
you choose will most likely depend upon the availability of matching terminals on both the
projector and the Video source device as described below:
Best video quality
The best available video connection method is HDMI. If your source device is equipped
with a HDMI socket, you can enjoy uncompressed digital video quality.
See "Connecting an HDMI device" on page 20 for how to connect the projector to a HDMI
source device and other details.
If no HDMI source is available, the next best video signal is Component video (not to be
confused with composite video). Digital TV tuner and DVD players output Component
video natively, so if available on your devices, this should be your connection method of
choice in preference to (composite) video.
See "Connecting a Component Video source device" on page 20 for how to connect the
projector to a component video device.
Better video quality
The S-Video method provides a better quality analog video than standard composite Video.
If you have both composite Video and S-Video output terminals on your Video source
device, you should elect to use the S-Video option.
See "Connecting an S-Video source device" on page 21 for how to connect the projector to
an S-Video device.
Least video quality
Composite Video is an analog video and will result in a perfectly acceptable, but less than
optimal result from your projector, being the least video quality of the available methods
described here.
See "Connecting a composite Video source device" on page 21 for how to connect the
projector to a composite Video device.
Connecting audio
The projector has one built-in mono speaker which is designed to provide basic audio
functionality accompanying data presentations for business purposes only. They are not
designed for, nor intended for stereo audio reproduction use as might be expected in home
theater or home cinema applications. Any stereo audio input (if provided), is mixed into a
common mono audio output through the projector speaker.
The table below describes where the sound is from when different source is connected.
Input source COMPUTER IN 1 COMPUTER IN 2, VIDEO, S-VIDEO
The projector can play
the sound from...
AUDIO IN 1 AUDIO IN 2
20
If you wish, you can make use of the projector (mixed mono) speaker in your presentations,
and also connect separate amplified speakers to the Audio Out socket of the projector. The
audio output is a mixed mono signal and controlled by the projector Volume and Mute
settings.
If you have a separate sound system, you will most likely want to connect the audio output
of your Video source device to that sound system, instead of to the mono audio projector.
Connecting an HDMI device
You should use an HDMI cable when making connection between the projector and HDMI
devices.
To connect the projector to an HDMI device:
1. Take an HDMI cable and connect one end to the HDMI-output port of the video
device.
2. Connect the other end of the cable to the HDMI-input port on the projector.
In the unlikely event that you connect the projector to a DVD player via the projector’s
HDMI input and the projected picture displays wrong colors, please change the color
space to YUV. See "Changing Color Space" on page 27 for details.
The projector is only capable of playing mixed mono audio, even if a stereo audio input is
connected. See "Connecting audio" on page 19 for details.
The HDMI input port is only available on the PJD6223/PJD6253/PJD6553w series.
Connecting a Component Video source device
Examine your Video source device to determine if it has a set of unused Component Video
output sockets available:
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a Component Video source device:
1. Take a Component Video to VGA (D-Sub) adaptor cable and connect the end with 3
RCA type connectors to the Component Video output sockets of the Video source
device. Match the color of the plugs to the color of the sockets; green to green, blue to
blue, and red to red.
2. Connect the other end of the Component Video to VGA (D-Sub) adaptor cable (with a
D-Sub type connector) to the COMPUTER IN 1 or COMPUTER IN 2 socket on the
projector.
The projector is only capable of playing mixed mono audio, even if a stereo audio input is
connected. See "Connecting audio" on page 19 for details.
If the selected video image is not displayed after the projector is turned on and the correct
video source has been selected, check that the Video source device is turned on and
operating correctly. Also check that the signal cables have been connected correctly.
VGA-Component adapter
(ViewSonic P/N: CB-00008906)
21
Connecting an S-Video source device
Examine your Video source device to determine if it has an unused S-Video output socket
available:
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to an S-Video source device:
1. Take an S-Video cable and connect one end to the S-Video output socket of the Video
source device.
2. Connect the other end of the S-Video cable to the S-VIDEO socket on the projector.
The projector is only capable of playing mixed mono audio, even if a stereo audio input is
connected. See "Connecting audio" on page 19 for details.
If the selected video image is not displayed after the projector is turned on and the correct
video source has been selected, check that the Video source device is turned on and
operating correctly. Also check that the signal cables have been connected correctly.
If you have already made a Component Video connection between the projector and this
S-Video source device using Component Video connections, you need not connect to this
device using an S-Video connection as this makes an unnecessary second connection of
poorer picture quality. See "Connecting Video source devices" on page 19 for details.
Connecting a composite Video source device
Examine your Video source device to determine if it has a set of unused composite Video
output sockets available:
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a composite Video source device:
1. Take a Video cable and connect one end to the composite Video output socket of the
Video source device.
2. Connect the other end of the Video cable to the VIDEO socket on the projector.
The projector is only capable of playing mixed mono audio, even if a stereo audio input is
connected. See "Connecting audio" on page 19 for details.
If the selected video image is not displayed after the projector is turned on and the correct
video source has been selected, check that the Video source device is turned on and
operating correctly. Also check that the signal cables have been connected correctly.
You need only connect to this device using a composite Video connection if Component
Video and S-Video inputs are unavailable for use. See "Connecting Video source devices"
on page 19 for details.
22
Operation
Starting up the projector
1. Plug the power cord into the projector and into a
wall socket. Turn on the wall socket switch
(where fitted). Check that the POWER
indicator light on the projector flashes blue
after power has been applied.
2. Press POWER on the projector or remote
control to start the projector. The POWER
indicator light stays blue when the projector is
on.
(If necessary) Rotate the focus ring to adjust the image clearness.
If the projector is still hot from previous activity, it will run the cooling fan for
approximately 90 seconds before energizing the lamp.
To maintain the lamp life, once you turn the projector on, wait at least 5 minutes before
turning it off.
3. If the projector is activated for the first time, select your OSD language following the
on-screen instructions.
4. Switch all of the connected equipment on.
5. The projector will start to search for input signals. The current input signal being
scanned appears in the upper left corner of the screen. If the projector doesn't detect a
valid signal, the message 'No Signal' will continue to be displayed until an input
signal is found.
You can also press SOURCE on the projector or remote control to select your desired
input signal. See "Switching input signal" on page 27 for details.
If the frequency/resolution of the input signal exceeds the projector's operating range, you will
see the message 'Out of Range' displayed on a blank screen. Please change to an input signal
which is compatible with the projector's resolution or set the input signal to a lower setting.
See "Timing chart" on page 67 for details.
I
I
23
Using the menus
The projector is equipped with On-Screen Display (OSD) menus for making various
adjustments and settings.
The OSD screenshots below are for reference only, and may differ from the actual design.
Below is the overview of the OSD menu.
To use the OSD menus, please set them to your familiar language first.
1. Press MENU/EXIT on the projector or
Menu on the remote control to turn the
OSD menu on.
3. Press to highlight
Language and press / to
select a preferred language.
2. Use / to highlight the SYSTEM
SETUP: Basic menu.
4. Press MENU/EXIT twice* on
the projector or Exit on the
remote control to leave and
save the settings.
*The first press leads you back
to the main menu and the
second press closes the OSD
menu.
: DISPLAY
: PICTURE
: SOURCE
: SYSTEM SETUP: Basic
: SYSTEM SETUP: Advanced
: INFORMATION
Current input
signal
Main menu icon
Sub-menu
Highlight
Go to the
previous page
or to exit.
Status
Screen Color
Aspect Ratio
Phase
H. Size
Zoom
Off
Auto
16
0
MENU Exit
Analog RGB
ENTER
Keystone
Position
3D Sync On
Disable3D Sync Invert
Color Management
Screen Color
Aspect Ratio
Position
Phase
H. Size
Zoom
Off
Auto
MENU
Exit
Keystone
16
0
Analog RGB
3D Sync On
3D Sync Invert
Color Management
Disable
Projector Position
Auto Power Off
Blank Timer
Timer Controller
Panel Key Lock
Splash Screen
Analog RGB
MENU Exit
Front Table
Disable
Disable
Off
Disable
ViewSonic
English
Language
Screen Capture
Message On
LAN Control Settings
Projector Position
Auto Power Off
Blank Timer
Timer Controller
Panel Key Lock
Splash Screen
Analog RGB
MENU Exit
Front Table
Disable
Disable
Off
Disable
ViewSonic
EnglishLanguage
Screen Capture
Message On
LAN Control Settings
24
Utilizing the password function
For security purposes and to help prevent unauthorized use, the projector includes an option
for setting up password security. The password can be set through the On-Screen Display
(OSD) menu. For details of the OSD menu operation, please refer to "Using the menus" on
page 23.
You will be inconvenienced if you activate the password functionality and subsequently forget
the password. Print this user manual (if necessary) and write the password you used in this
manual, and keep it in a safe place for later use.
Setting a password
1. Open the OSD menu and go to the SYSTEM SETUP: Advanced > Security
Settings menu. Press MODE/ENTER on the projector or Enter on the remote
control. The Security Settings page is displayed.
2. Highlight Power On Lock and select On by pressing / .
3. As pictured to the right, the four arrow keys
( , , , ) respectively represent 4 digits
(1, 2, 3, 4). According to the password you desire
to set, press the arrow keys to enter six digits for
the password.
4. Confirm the new password by re-entering the
new password.
Once the password is set, the OSD menu returns to the Security Settings page.
5. To leave the OSD menu, press MENU/EXIT on the projector or Exit on the remote
control.
Once a password has been set, the projector cannot be used unless the correct password
is entered every time the projector is started.
The digits being input will be displayed as asterisks on-screen. Write your selected
password down here in this user manual in advance or right after the password is entered
so that it is available to you should you ever forget it.
Password: __ __ __ __ __ __
Keep this user manual in a safe place.
If you forget the password
If the password function is activated, you will be asked
to enter the six-digit password every time you turn on
the projector. If you enter the wrong password, the
password error message as pictured to the right is
displayed lasting for three seconds, and the message
'INPUT PASSWORD' follows. You can retry by
entering another six-digit password, or if you did not
record the password in this user manual, and you absolutely do not remember it, you can use
the password recall procedure. See "Entering the password recall procedure" on page 25 for
details.
If you enter an incorrect password 5 times in succession, the projector will automatically
shut down in a short time.
INPUT NEW PASSWORD
BackMENU
Password Error
Please try again.
25
Entering the password recall procedure
1. Press and hold AUTO on the projector or Auto
Sync on the remote control for 3 seconds. The
projector will display a coded number on the
screen.
2. Write down the number and turn off your
projector.
3. Seek help from the local service center to decode
the number. You may be required to provide
proof of purchase documentation to verify that you are an authorized user of the
projector.
Changing the password
1. Open the OSD menu and go to the SYSTEM SETUP: Advanced > Security
Settings > Change Password menu.
2. Press MODE/ENTER on the projector or Enter on the remote control. The message
'INPUT CURRENT PASSWORD' is displayed.
3. Enter the old password.
If the password is correct, another message 'INPUT NEW PASSWORD' is
displayed.
If the password is incorrect, the password error message is displayed lasting for
three seconds, and the message 'INPUT CURRENT PASSWORD' is
displayed for your retry. You can press MENU/EXIT on the projector or Exit
on the remote control to cancel the change or try another password.
4. Enter a new password.
5. Confirm the new password by re-entering the new password.
6. You have successfully assigned a new password to the projector. Remember to enter
the new password next time the projector is started.
7. To leave the OSD menu, press MENU/EXIT on the projector or Exit on the remote
control.
The digits being input will be displayed as asterisks on-screen. Write your selected password
down here in this user manual in advance or right after the password is entered so that it is
available to you should you ever forget it.
Password: __ __ __ __ __ __
Keep this user manual in a safe place.
Please write down the recall code,
and contact ViewSonic
Customer Center.
Recall code:
0 2 1 2
RECALL PASSWORD
Exit
MENU
26
Disabling the password function
To disable password protection, go back to the SYSTEM SETUP: Advanced > Security
Settings > Power On Lock menu after opening the OSD menu system. Select Off by
pressing / . The message 'INPUT PASSWORD' is displayed. Enter the current
password.
If the password is correct, the OSD menu returns to the Security Settings page
with 'Off' shown in the row of Power On Lock. You will not have to enter the
password next time you turn on the projector.
If the password is incorrect, the password error message is displayed lasting for
three seconds, and the message 'INPUT PASSWORD' is displayed for your
retry. You can press MENU/EXIT on the projector or Exit on the remote
control to cancel the change or try another password.
Though the password function is disabled, you need to keep the old password in hand should
you ever need to re-activate the password function by entering the old password.
27
Switching input signal
The projector can be connected to multiple devices at the same time. However, it can only
display one full screen at a time.
Be sure the Quick Auto Search function in the SOURCE menu is On if you want the
projector to automatically search for the signals.
You can also manually select the desired signal by
pressing one of the source selection keys on the
remote control, or cycle through the available input
signals.
1. Press SOURCE on the projector or remote
control. A source selection bar is displayed.
2. Press / until your desired signal is
selected and press MODE/ENTER on the
projector or Enter on the remote control.
Once detected, the selected source information
will be displayed on the screen for seconds. If
there are multiple devices connected to the
projector, repeat steps 1-2 to search for another
signal.
The brightness level of the projected image will
change accordingly when you switch between
different input signals. Data (graphic) "PC"
presentations using mostly static images are
generally brighter than "Video" using mostly
moving images (movies).
The input signal type effects the options available
for the Color Mode. See "Selecting a picture
mode" on page 32 for details.
Please see "Projector specifications" on page 64
for the native display resolution of this projector.
For best display picture results, you should select
and use an input signal which outputs at this
resolution. Any other resolutions will be scaled by
the projector depending upon the 'aspect ratio'
setting, which may cause some image distortion
or loss of picture clarity. See "Selecting the aspect
ratio" on page 30 for details.
Changing Color Space
This function is only available for the PJD6223/PJD6253/PJD6353/PJD6353s/PJD6383/PJD6553w/
PJD6383s/PJD6 53w/PJD6653ws/PJD6683w/PJD6683ws series.
In the unlikely event that you connect the projector to a DVD player via the projectors
HDMI input and the projected picture displays wrong colors, please change the color space
to YUV.
To do this:
1. Open the OSD menu and go to the SOURCE menu.
2. Press to highlight Color Space Conversion and press / to select a suitable
color space.
This function is only available when the HDMI-input port is in use.
D-Sub / Comp. 1
Video
S-Video
D-Sub / Comp. 2
PJD5126/PJD5226/PJD5226w
PJD6223/PJD6253/PJD6353/
PJD6553w/PJD6653w/PJD6653ws
PJD6683w/PJD6683ws
D-Sub / Comp. 1
Video
S-Video
D-Sub / Comp. 2
HDMI
PJD6353s/PJD6383/PJD6383s/
6
28
Adjusting the projected image
Adjusting the projection angle
The projector is equipped with 1 quick-release adjuster foot and 2 rear adjuster feet. These
adjusters change the image height and projection angle. To adjust the projector:
1. Press the quick-release button and lift the
front of the projector. Once the image is
positioned where you want it, release the
quick-release button to lock the foot in
position.
2. Screw the rear adjuster feet to fine tune the
horizontal angle.
To retract the foot, hold up the projector while
pressing the quick-release button, then slowly lower the projector. Screw the rear adjuster
feet in a reverse direction.
If the projector is not placed on a flat surface or the screen and the projector are not
perpendicular to each other, the projected image becomes trapezoidal. To correct this
situation, see "Correcting keystone" on page 29 for details.
Do not look into the lens while the lamp is on. The strong light from the lamp may cause
damage to your eyes.
Be careful when you press the adjuster button as it is close to the exhaust vent where hot
air comes from.
Auto-adjusting the image
In some cases, you may need to optimize the picture quality. To do this, press AUTO on the
projector or Auto Sync on the remote control. Within 3 seconds, the built-in Intelligent
Auto Adjustment function will re-adjust the values of Frequency and Clock to provide the
best picture quality.
The current source information will be displayed in the upper left corner of the screen for 3
seconds.
The screen will be blank while AUTO is functioning.
This function is only available when PC signal (analog RGB) is selected.
Fine-tuning the image clarity
1
2
1. Adjust the projected image to the size
that you need using the zoom ring.
2. If necessary, Sharpen the image by
rotating the focus ring.
PJD5126/PJD5226/
PJD5226w/PJD6223/
PJD6253/PJD6553w
PJD6353/PJD6353s/
PJD6653w/PJD6653ws/
PJD6383/PJD6383s/
PJD66 3w/PJ
D66 3ws/
8
8
29
Correcting keystone
Keystoning refers to the situation where the projected image is noticeably wider at either the
top or bottom. It occurs when the projector is not perpendicular to the screen.
To correct this, besides adjusting the height of the projector, you will need to manually
correct it following one of these steps.
Using the remote control
Press / on the projector or remote control to
display the Keystone correction page. Press to
correct keystoning at the top of the image. Press
to correct keystoning at the bottom of the image.
Using the OSD menu
1. Press MENU/EXIT on the projector or Menu on the remote control and then press
/ until the
DISPLAY menu is highlighted.
2. Press to highlight Keystone and press MODE/ENTER on the projector or Enter
on the remote control. The Keystone correction page is displayed.
3. Press to correct keystoning at the top of the image or press to correct
keystoning at the bottom of the image.
Magnifying and searching for details
If you need to find the details on the projected picture, magnify the picture. Use the
direction arrow keys for navigating the picture.
Using the remote control
1. Press Magnify on the remote control to display the Zoom bar.
2. Press repeatedly to magnify the picture to a desired size.
3. To navigate the picture, press MODE/ENTER on the projector or Enter on the
remote control to switch to the paning mode and press the directional arrows
( , , , ) to navigate the picture.
4. To reduce size of the picture, press MODE/ENTER on the projector or Enter on the
remote control to switch back to the zoom in/out functionality, and press AUTO/Auto
Sync to restore the picture to its original size. You can also press repeatedly until
it is restored to the original size.
Using the OSD menu
1. Press MENU/EXIT on the projector or Menu on the remote control and then press
/ until the DISPLAY menu is highlighted.
2. Press
to highlight Zoom and press MODE/ENTER on the projector or Enter on
the remote control. The Zoom bar is displayed.
3. Repeat steps 2-4 in the section of Using the remote control above.
The picture can only be navigated after the picture is magnified. You can further magnify the
picture while searching for details.
Press /.
Press /.
30
Selecting the aspect ratio
The 'aspect ratio' is the ratio of the image width to the image height. Most analog TV and
computers are in 4:3 ratio, and digital TV and DVDs are usually in 16:9 ratio.
With the advent of digital signal processing, digital display devices like this projector can
dynamically stretch and scale the image output to a different aspect than that of the image
input signal.
To change the projected image ratio (no matter what aspect the source is):
Using the remote control
1. Press Aspect to show the current setting.
2. Press Aspect repeatedly to select an aspect ratio to suit the!format of the video signal
and your display requirements.
Using the OSD menu
1. Press MENU/EXIT on the projector or Menu on the remote control and then press
/ until the DISPLAY menu is highlighted.
2. Press
to highlight Aspect Ratio.
3. Press / to select an aspect ratio to suit the format of the video signal and your
display requirements.
31
About the aspect ratio
In the pictures below, the black portions are inactive areas and the white portions are active
areas. OSD menus can be displayed on those unused black areas.
1. Auto: Scales an image proportionally to fit the
projector's native resolution in its horizontal
width. This is suitable for the incoming image
which is neither in 4:3 nor 16:9 and you want to
make most use of the screen without altering the
image's aspect ratio.
2. 4:3: Scales an image so that it is displayed in the
center of the screen with a 4:3 aspect ratio. This
is most suitable for 4:3 images like computer
monitors, standard definition TV and 4:3 aspect
DVD movies, as it displays them without aspect
alteration.
3. 16:9: Scales an image so that it is displayed in
the center of the screen with a 16:9 aspect ratio.
This is most suitable for images which are
already in a 16:9 aspect, like high definition TV,
as it displays them without aspect alteration.
4. 16:10 (PJD5226w/PJD6553w/PJD6653w/
Scales an image so that it is
center of the screen with a 16:10
This is most suitable for images which
already in a 16:10 aspect, as it displays them
without aspect alteration
16:10 picture
15:9 picture
4:3 picture
16:9 picture
16:10 picture
PJD6653ws/PJD6683w/PJD6683ws only):
displayed in the
aspect ratio.
are
32
Optimizing the image
Selecting a picture mode
The projector is preset with several predefined picture modes so that you can choose one to
suit your operating environment and input signal picture type.
To select an operation mode that suits your need, you can follow one of the following steps.
Press MODE/ENTER on the projector or Color Mode on the remote control
repeatedly until your desired mode is selected.
•Go to the PICTURE > Color Mode menu and press / to select a desired mode.
Picture modes for different types of signals
The picture modes available for different types of signals are listed below.
PC input signals: D-Sub / Comp. 1/2 (analog RGB)
1. Brightest mode: Maximizes the brightness of the projected image. This mode is
suitable for environments where extra-high brightness is required, such as using the
projector in well lit rooms.
2. PC mode: Is designed for presentations under daylight environment to match PC and
notebook coloring.
3. ViewMatch mode: Switches between high brightness performance and accurate color
performance.
4. Movie mode:!Is appropriate for playing colorful movies, video clips from digital
cameras or DVs through the PC input for best viewing in a blackened (little light)
environment.
5. Dynamic PC mode: Is designed for presentations under daylight environment to
match PC and notebook coloring. In addition, the projector will optimize the image
quality using the dynamic PC function in accordance with the projected contents.
It takes some time to initiate this function. Make sure the projector has been turned on for
more than 4 minutes.
If the projector is resumed by using the Smart Restart feature, this function can be executed
immediately.
6. Dynamic Movie mode:!Is appropriate for playing colorful movies, video clips from
digital cameras or DVs through the PC input for best viewing in a blackened (little
light) environment. In addition, the projector will optimize the image quality using the
dynamic Movie function in accordance with the projected contents.
It takes some time to initiate this function. Make sure the projector has been turned on for
more than 4 minutes.
If the projector is resumed by using the Smart Restart feature, this function can be executed
immediately.
7. User 1/User 2 mode: Recalls the settings customized based on the current available
picture modes. See "Setting the User 1/User 2 mode" on page 33 for details.
Video input signals: S-Video, Video, D-Sub / Comp. 1/2 (YPbPr) / HDMI
1. Brightest mode: Optimized for daylight viewing, with living room level ambient
brightness.
2. Gaming mode: Suitable for all types of entertainment media, including gaming and
movies.
33
3. ViewMatch mode: Switches between high brightness performance and accurate color
performance.
4. Movie mode: Is suitable for enjoying dark movies or DVD movies best viewed in a
blackened (little light) home cinema or lounge room environment.
5. Dynamic Movie mode: Is suitable for enjoying dark movies or DVD movies best
viewed in a blackened (little light) home cinema or lounge room environment. In
addition, the projector will optimize the image quality using the dynamic Movie
function in accordance with the projected contents.
It takes some time to initiate this function. Make sure the projector has been turned on for
more than 4 minutes.
If the projector is resumed by using the Smart Restart feature, this function can be executed
immediately.
6. User 1/User 2 mode: Recalls the settings customized based on the current available
picture modes. See "Setting the User 1/User 2 mode" on page 33 for details.
Setting the User 1/User 2 mode
There are two user-definable modes if the current available picture modes are not suitable
for your need. You can use one of the picture modes (except the User 1/User 2) as a starting
point and customize the settings.
1. Press MENU/EXIT on the projector or Menu on the remote control to open the On-
Screen Display (OSD) menu.
2. Go to the PICTURE > Color Mode menu.
3. Press / to select User 1 or User 2.
4. Press to highlight Reference Mode.
This function is only available when User 1 or User 2 mode is selected up in the Color Mode
sub-menu item.
5. Press / to select a picture mode that is closest to your need.
6. Press to select a sub-menu item to be changed and adjust the value with / .
See Fine-tuning the image quality in user modes below for details.
7. When all settings have been done, highlight Save Settings and press MODE/ENTER
on the projector or Enter on the remote control to store the settings.
8. The confirmation message 'Setting Saved' is displayed.
Using Screen Color
In the situation where you are projecting onto a colored surface such as a painted wall which
may not be white, the Screen Color feature can help correct the projected picture’s colors to
prevent possible color difference between the source and projected pictures.
To use this function, go to the DISPLAY > Screen Color menu and press / to select a
color which is closest to the color of the projection surface. There are several precalibrated
colors to choose from: Whiteboard, Greenboard, and Blackboard.
This function is only available when a PC type input signal is selected.
Fine-tuning the image quality in user modes
According to the detected signal type, there are some user-definable functions available
when User 1 or User 2 mode is selected. You can make adjustments to these functions
based on your needs.
34
Adjusting Brightness
Highlight the PICTURE > Brightness menu and press / .
The higher the value, the brighter the image. And the
lower the setting, the darker the image. Adjust this
control so the black areas of the image appear just as
black and that detail in the dark areas is visible.
Adjusting Contrast
Highlight the PICTURE > Contrast menu and press / .
The higher the value, the greater the contrast. Use this
to set the peak white level after you have previously
adjusted the Brightness setting to suit your selected
input and viewing environment.
Adjusting Color
Highlight the PICTURE > Color menu and press / .
Lower setting produces less saturated colors. If the setting is too high, colors on the image
will be overpowering, which makes the image unrealistic.
Adjusting Tint
Highlight the PICTURE > Tint menu and press / .
The higher the value, the more reddish the picture becomes. The lower the value, the more
greenish the picture becomes.
Adjusting Sharpness
Highlight the PICTURE > Sharpness menu and press / .
The higher the value, the sharper the picture becomes. The lower the value, the softer the
picture becomes.
Adjusting Brilliant Color
Highlight the PICTURE > Brilliant Color menu and press / .
This feature utilizes a new color-processing algorithm and system level enhancements to
enable higher brightness while providing truer, more vibrant colors in the projected picture.
It enables a greater than 50% brightness increase in mid-tone images, which are common in
video and natural scenes, so the projector reproduces images in realistic and true colors. If
you prefer images with that quality, select On. If you don’t need it, select Off.
When Off is selected, the Color Temperature function is not available.
Selecting a Color Temperature
Highlight the PICTURE > Color Temperature menu and press / .
The options available for color temperature* settings vary according to the signal type
selected.
1. T1: With the highest color temperature, T1 makes the image appear the most bluish
white than other settings.
2. T2: Makes images appear bluish white.
3. T3: Maintains normal colorings for white.
4. T4: Makes images appear reddish white.
+50
+30
+70
0
-30
+30
35
*About color temperatures:
There are many different shades that are considered to be "white" for various purposes. One
of the common methods of representing white color is known as the “color temperature”. A
white color with a low color temperature appears to be reddish white. A white color with a
high color temperature appears to have more blue in it.
Color Management
Only in permanent installations with controlled lighting levels such as boardrooms, lecture
theaters, or home theaters, should color management be considered. Color management
provides fine color control adjustment to allow for more accurate color reproduction, should
you require it.
If you have purchased a test disc which contains various color test patterns and can be used
to test the color presentation on monitors, TVs, projectors, etc., you can project any image
from the disc on the screen and enter the Color Management menu to make adjustments.
To adjust the settings:
1. Go to the DISPLAY menu and highlight Color Management.
2. Press MODE/ENTER on the projector or Enter on the remote control and the Color
Management page is displayed.
3. Highlight Primary Color and press / to select a color from among Red, Yellow,
Green, Cyan, Blue, or Magenta.
4. Press to highlight Hue and press / to select its range. Increase in the range
will include colors consisted of more proportions of its two adjacent colors.
Please refer to the illustration to the right for
how the colors relate to each other.
For example, if you select Red and set its
range at 0, only pure red in the projected
picture will be selected. Increasing its range
will include red close to yellow and red close
to magenta.
5. Press to highlight Saturation and adjust
its values to your preference by pressing /
. Every adjustment made will reflect to the
image immediately.
For example, if you select Red and set its
value at 0, only the saturation of pure red will be affected.
Saturation is the amount of that color in a video picture. Lower settings produce less
saturated colors; a setting of “0” removes that color from the image entirely. If the saturation
is too high, that color will be overpowering and unrealistic.
6. Press to highlight Gain and adjust its values to your preference by pressing /
. The contrast level of the primary color you select will be affected. Every
adjustment made will reflect to the image immediately.
7. Repeat steps 3 to 6 for other color adjustments.
8. Make sure you have made all of the desired adjustments.
9. Press MENU/EXIT on the projector or Exit on the remote control to exit and save the
settings.
RED
BLUE
GREEN
Yellow
Cyan
Magenta
36
Setting the presentation timer
Presentation timer can indicate the presentation time on the screen to help you achieve
better time management when giving presentations. Follow these steps to utilize this
function:
1. Press Timer on the remote control to access the Presentation Timer menu or go to
the SYSTEM SETUP: Advanced > Presentation Timer menu and press MODE/
ENTER to display the Presentation Timer page.
2. Highlight Timer Period and decide the time period by pressing / . The length of
time can be set from 1 to 5 minutes in 1-minute increments and 5 to 240 minutes in 5-
minute increments.
If the timer is already on, the timer will restart whenever the Timer Period is reset.
3. Press to highlight Timer Display and choose if you want the timer to show up on
the screen by press
ing / .
4. Press to highlight Timer Position and set the timer position by pressing / .
5. Press to highlight Timer Counting Direction and select your desired counting
direction by pressing / .
6. Press to highlight Sound Reminder and decide if you want to activate sound
reminder by pressing / . If you select On, a double beep sound will be heard at
the last 30 seconds of counting down/up, and a triple beep sound will be produced
when the timer is up.
7. To activate the presentation timer, press and press / to highlight Start
Counting and press MODE/ENTER.
8. A confirmation message displays. Highlight Yes and press MODE/ENTER on the
projector or remote control to confirm. You will see the message “Timer is On
displaying on the screen. The timer starts counting when the timer is on.
To cancel the timer, perform the following steps:
1. Go to the SYSTEM SETUP: Advanced > Presentation Timer menu and highlight
Off. Press MODE/ENTER. A confirmation message displays.
2. Highlight Yes and press MODE/ENTER to confirm. You will see the message
“Timer is Off” displaying on the screen.
Selection Description
Always
Displays the timer on screen throughout the presentation
time.
1 min/2 min/3 min Displays the timer on screen in the last 1/2/3 minute(s).
Never Hides the timer throughout the presentation time.
Top-Left Bottom-Left Top-Right Bottom-Right
Selection Description
Count Up Increases from 0 to the preset time.
Count Down Decreases from the preset time to 0.
37
Hiding the image
In order to draw the audience's full attention to the presenter, you can use on the
projector or Blank on the remote control to hide the screen image. Press any key on the
projector or remote control to restore the image. The word 'BLANK' appears at the lower
right corner of the screen while the image is hidden.
You can set the blank time in the SYSTEM SETUP: Basic > Blank Timer menu to let
the projector return the image automatically after a period of time when there is no action
taken on the blank screen.
Once Blank is pressed, the projector enters Economic mode automatically.
CAUTION
Do not block the projection lens from projecting as this could cause the blocking object to
become heated and deformed or even cause a fire.
Locking control keys
With the control keys on the projector locked, you can prevent your projector settings from
being changed accidentally (by children, for example). When the Panel Key Lock is on, no
control keys on the projector will operate except POWER.
1. Press on the projector or Lock on the remote control, or go to the
SYSTEM
SETUP: Basic > Panel Key Lock menu
, and select On by pressing / on the
projector or remote control.
2. A confirmation message is displayed. Select Yes to confirm.
To release panel key lock, press and hold on the projector or Lock on the remote
control for 3 seconds.
You can also use the remote control to enter the SYSTEM SETUP: Basic > Panel Key
Lock menu and press / to select Off.
Keys on the remote control are still functional when panel key lock is enabled.
If you press POWER to turn off the projector without disabling panel key lock, the
projector will still be in locked status the next time it is turned on.
Freezing the image
Press Freeze on the remote control to freeze the image. The word 'FREEZE' will be
displayed in the upper left corner of the screen. To release the function, press any key on the
projector or remote control.
Even if an image is frozen on the screen, the pictures are running on the video or other
device. If the connected devices have active audio output, you will still hear the audio even
though the image is frozen on screen.
Operating in a high altitude environment
We recommend you use the High Altitude Mode when your environment is between 1500
m–3000 m above sea level, and temperature is between 0°C–35°C.
CAUTION
Do not use the High Altitude Mode if your altitude is between 0 m and 1500 m and temperature
is between 0°C and 35°C. The projector will be over cooled, if you turn the mode on under
such a condition.
I
I
I
I
38
To activate the High Altitude Mode:
1. Press MENU/EXIT on the projector or Menu on
the remote control and then press / until the
SYSTEM SETUP: Advanced menu is
highlighted.
2. Press to highlight High Altitude Mode and
press / to select On. A confirmation
message is displayed.
3. Highlight Yes and press MODE/ENTER on the projector or Enter on the remote
control.
Operation under "High Altitude Mode" may cause a higher decibel operating noise level
because of increased fan speed necessary to improve overall system cooling and
performance.
If you use this projector under other extreme conditions excluding the above, it may display
auto shut-down symptoms, which is designed to protect your projector from over-heating.
In cases like this, you should switch to High Altitude Mode to solve these symptoms.
However, this is not to state that this projector can operate under any and all harsh or
extreme conditions.
Creating your own startup screen
This function is only available for the PJD6223/PJD6253/PJD6353/PJD6353s/PJD6383/PJD6383s/
PJD6653w/PJD6653ws series.
In addition to selecting the projector preset startup screen from among ViewSonic logo,
Black or Blue screen, you can make your own startup screen that is a picture projected from
your computer or video source.
To create your own startup screen, project the picture you want to use as your startup screen
from either a computer or video source. The rest of the steps are as follows.
1. Press MENU/EXIT on the projector or Menu on the remote control and then press
/ until the SYSTEM SETUP: Basic menu is highlighted.
2. Press to highlight Screen Capture and press MODE/ENTER on the projector or
Enter on the remote control.
3. A confirmation message is displayed. Press MODE/ENTER on the projector or
Enter on the remote control again.
4. The message 'Screen Capturing...' is displayed while the projector is processing the
picture. Please wait.
5. If the action is successful, you see the message 'Capture Succeeded' on the screen.
The captured picture is saved as Screen Capture and the captured picture will be
displayed as the startup screen if you restart the projector.
In the unlikely event that the capturing action fails, change your target picture. When the
resolution of the input signal is higher than the projector’s native display resolution (See
"Projector specifications" on page 64 for details.), the capture action may fail. When it
happens, please set the resolution of the input signal under native resolution and try again.
We recommend you use the High Altitude
mode by selecting it whenever your
environment is higher than 1500 m.
Do you want to turn High Altitude Mode
ON?
Yes
No
Notice
PJD6553w/ /PJD6683w/PJD6683ws
39
Controlling the projector through a LAN
environment
This function is only available for the PJD6223/PJD6253/PJD6353/PJD6353s/PJD6383/PJD6383s
PJD6 3w/PJD66 3w series.
The projector supports Crestron
®
software. With correct settings for the LAN Control
Settings menu, you can manage the projector from a computer using a web browser when
the computer and the projector are properly connected to the same local area network.
Configuring the LAN Control Settings
If you are in a DHCP environment:
1. Take a RJ45 cable and connect one end to the RJ45 LAN input jack of the projector
and the other end to the RJ45 port.
2. Press MENU/EXIT on the projector or Menu on the remote control and then press
/ until the SYSTEM SETUP: Basic menu is highlighted.
3. Press to highlight LAN Control Settings and press MODE/ENTER on the
projector or Enter on the remote control. The LAN Control Settings page is
displayed.
4. Press to highlight DHCP and press / to select On.
5. Press to highlight Apply and press MODE/ENTER on the projector or Enter on
the remote control.
6. Please wait for around 15 - 20 seconds, and then re-enter the LAN Control Settings
page. The Projector IP Address, Subnet Mask, Default Gateway, and DNS Server
settings will be displayed. Note down the IP address displayed in the Projector IP
Address row.
If the Projector IP Address still does not appear, contact your network administrator.
If the RJ45 cables are not properly connected, the Projector IP Address, Subnet Mask,
Default Gateway, and DNS Server settings will display 0.0.0.0. Make sure the cables are
properly connected and perform the procedures above again.
If you need to connect to the projector in its standby mode, set Power Saving to Off.
TYPE B
USB
LAN
RS-232
(An example of connection)
55 5 /PJD6653ws/PJD6683w/PJD6683ws
40
If you are in a non-DHCP environment:
1. Repeat steps 1-3 above.
2. Press to highlight DHCP and press / to select Off.
3. Contact your ITS administrator for information on the Projector IP Address, Subnet
Mask, Default Gateway, and DNS Server settings.
4. Press to select the item you want to modify and press MODE/ENTER on the
projector or Enter on the remote control.
5. Press / to move the cursor and the press / to enter the value.
6. To save the settings, press MODE/ENTER on the projector or Enter on the remote
control. If you do not want to save the settings, press MENU/EXIT on the projector
or Menu on the remote control.
7. Press to highlight Apply and press MODE/ENTER on the projector or Enter on
the remote control.
If the RJ45 cables are not properly connected, the Projector IP Address, Subnet Mask,
Default Gateway, and DNS Server settings will display 0.0.0.0. Make sure the cables are
properly connected and perform the procedures above again.
If you wish to connect to the projector in its standby mode, be sure you have selected
RJ45 and obtained the Projector IP Address, Subnet Mask, Default Gateway, and DNS
Server information when the projector is on.
Controlling the projector through a web browser
Once you have the correct IP address for the projector and the projector is on or in standby
mode, you can use any computer that is on the same local area network to control the
projector.
If you are using Microsoft Internet Explorer, make sure it is version 7.0 or higher.
The screen shots in this manual are for reference only, and may differ from the actual
design.
1. Enter the address of the projector in the address bar of your browser and press Enter.
2. The main page of the Network Control appears.
Accessing to Network Settings or Email Alert page requires Administrator password. The
default password is "0000".
3. This page allows you to make adjustments to the AMX and SNMP settings. In the
AMX device discover row, when ON is selected, the projector can be detected by
5
4
3
41
controllers of AMX connected to the same network. For the Details of AMX Device
Discovery, visit the AMX web site at http://www.amx.com/.
4. If your projector is connected to a network which supports Simple Mail Transfer
Protocol (SMTP), you can configure it to alert you via email on significant events.
5. The Crestron (e-Control) page displays the Crestron e-Control user interface. See
"About Crestron e-Control®" on page 42 for details.
Please pay attention to the limitation of input length (including space and other punctuation
keys) in the list blow:
Category Item Input Length
Maximum Number
of Characters
Network Settings
Network
DHCP/Manual (N/A)
IP Address XXX.XXX.XXX.XXX
Subnet Mask XXX.XXX.XXX.XXX
Gateway XXX.XXX.XXX.XXX
DNS Server XXX.XXX.XXX.XXX
AMX device discovery (N/A)
Password
Administrator (N/A)
New Password 4
Confirm Password 4
SNMP
SysLocation 22
SysName 22
SysContact 22
42
/ > < $ % + \ ' " are prohibited
/
About Crestron e-Control
®
1. The Crestron e-Control
®
page provides a variety of virtual keys to control the
projector or adjust the projected pictures.
i. These buttons function the same as the ones on the OSD menus or remote control.
See "2. PICTURE menu" on page 51 and "Projector" on page 7 for details.
ii. To switch between input signals, click on your desired signal.
The Menu button can also be used to go back to previous OSD menus, exit and save menu
settings.
The source list varies according to the connectors available on the projector.
When you use the projector control panel or remote control to change the OSD menu
settings, it may take a while for the web browser to synchronize these changes with the
projector.
Email Alert
Email Setting
To 40
Cc 40
Subject 30
From 40
SMTP Setting
Server 30
User Name 40
Password 14
Alert Condition
Fan Error (N/A)
Lamp Error (N/A)
Over Temperature (N/A)
Lamp Time Alert (N/A)
Submit (N/A)
Issue Test Mail (N/A)
i
i
i
ii
You can press
/ to reveal
more buttons.
43
2. The tools page allows you to manage the projector, configure the LAN control
settings and secure access of remote network operation on this projector.
i. This section is only used with the Crestron Control System. Please contact
Creston or refer to its user manual for setup information.
ii. You can name the projector, keep track of its location and the person in charge of
it.
iii. You can adjust the LAN Control Settings.
iv. Once set, access to the remote network operation on this projector has been
password-protected.
v. Once set, access to the tools page has been password-protected.
To prevent errors, only input the English alphabet and digits on the tools page.
After making the adjustments, press the Send button and the data will be saved for the
projector.
vi. Press Exit to go back to the remote network operation page.
Please pay attention to the limitation of input length (including space and other punctuation
keys) in the list blow:
Category Item Input Length
Maximum Number of
Characters
Crestron Control
IP Address 15
IP ID 2
Port 5
Projector
Projector Name 10
Location 9
Assigned To 9
Network Configuration
DHCP (Enabled) (N/A)
IP Address 15
Subnet Mask 15
Default Gateway 15
DNS Server 15
i iv
iii
ii
v
vi
45
PJLink™, SNMP, AMX and Xpanel formats supported
This projector is PJLink™, SNMP V.1, AMX or Xpanel V1.10 compliant. For details,
please follow its user guide or website respectively to control and manage projectors.
Using the projector in standby mode
Some of the projector functions are available in standby mode (plugged in but not turned
on). To use these functions, be sure you have turned on the corresponding menus under
SYSTEM SETUP: Basic > Standby Settings, and the cable connections are correctly
made. For the connection methods, see the Connection chapter.
Power Saving
Less than 1W power consumption when Power Saving mode is turned on.
When Power Saving is On, the following settings are not available.
When Power Saving is On, the network function is not available when the projector is in
standby mode.
Active VGA Out
Selecting On outputs a VGA signal when the COMPUTER IN 1 and COMPUTER OUT
sockets are correctly connected to devices. The projector outputs the signal received only
from COMPUTER IN 1.
Active Audio Out
Selecting On outputs an audio signal when the AUDIO IN 1 and AUDIO OUT sockets are
correctly connected to devices. The projector outputs the audio signal received only from
AUDIO IN 1.
Quick Power Off
Selecting On enables the function and the projector will not enter the cooling process after
being shut down. Selecting Off disables the function and the projector will enter normal
cooling process after being shut down.
If you attempt to restart the projector right after it’s been turned off, it may not be turned
on successfully and will rerun its cooling procedure.
When Off is selected, the Smart Restart function will be automatically turned off.
Shutting down the projector
1. Press POWER and a confirmation message
is displayed prompting you.
If you don't respond in a few seconds, the
message will disappear.
2. Press POWER a second time.
3. Disconnect the power cord from the wall
socket if the projector will not be used in an
extended period of time.
CAUTION
To protect the lamp, the projector will not respond to any commands during the cooling
process.
To shorten the cooling time, you can also activate the Quick Power Off function. See
"Quick Power Off" on page 45 for details.
Do not unplug the power cord before the projector shutdown sequence is complete.
I
I
I
I
46
Menu operation
Menu system
Please note that the on-screen display (OSD) menus vary according to the signal type
selected.
The menu items are available when the projector detects at least one valid signal. If there is
no equipment connected to the projector or no signal detected, limited menu items are
accessible.
Main menu Sub-menu Options
1.
DISPLAY
Screen Color
Off/Blackboard/
Greenboard/Whiteboard
Aspect Ratio
Auto/4:3/16:9/
16:10 (
only)
Keystone
Position
Phase
H. Size
Zoom
3D Sync TI 3D DLP Link/Off
3D Sync Invert Disable/Invert
Color
Management
Primary Color R/G/B/C/M/Y
Hue
Saturation
Gain
2.
PICTURE
Color Mode
PC source: Brightest/PC/ViewMatch/Movie/
Dynamic PC/Dynamic Movie/User 1/User 2
Video source: Brightest/Gaming/ViewMatch/
Movie/Dynamic Movie/User 1/User 2
Reference Mode
PC source: Brightest/PC/ViewMatch/Movie/
Dynamic PC/Dynamic Movie
Video source: Brightest/Gaming/ViewMatch/
Movie/Dynamic Movie
Brightness
Contrast
Color
Tint
Sharpness
Brilliant Color On/Off
Color Temperature T1/T2/T3/T4
Save Settings
PJD5226w/
PJD6653ws/
PJD6683ws
PJD6553w/
PJD6 3w/65
PJD6683w/
47
Main menu Sub-menu Options
3. SOURCE
Quick Auto Search Off/On
Color Space Conversion (PJD6223/
PJD6253/PJD6353/PJD6353s/PJD6383/
only)
RGB/YUV/Auto
DynamicEco Timer
Disable/5 min/10 min/15
min/30 min
Smart Restart Off/On
Pattern
PJD5126/PJD5226/PJD5226w: Off/On
PJD6223/PJD6253/PJD6353/PJD6353s/PJD6383/PJD6383s:
01/02/03/04/05/User
PJD6553w/PJD6653w/PJD6653ws/PJD6683w/PJD6683ws:
01/02/03/04/User
My Button
Projection (Projector Position)/3D Sync/Lamp
Mode/DCR/Closed Caption/Auto Off (Auto Power
Off)/Message/Screen Color/Screen Capture
(PJD6223/PJD6253/PJD6353/PJD6353s/PJD6383/PJD6383s/PJD6553w/
PJD6653w/PJD6653ws/PJD6683w/PJD6683ws only)/Information
4.
SYSTEM
SETUP:
Basic
Language
Multi-language OSD
selection
Projector Position
Front Table/Rear Table/
Rear Ceiling/Front Ceiling
Auto Power Off
Disable/5 min/10 min/20
min/30 min/40 min/50 min/
60 min
Blank Timer
Disable/5 min/10 min/15
min/20 min/25 min/30 min
Panel Key Lock On/Off
Splash Screen
Black/Blue/ViewSonic/
Screen Capture (PJD6223/
PJD6253/PJD6353/PJD6353s/
PJD6383/PJD6383s/PJD6653w/
PJD6553w/PJD6653ws/PJD6683w
Off
Screen Capture (PJD6223/PJD6253/PJD6353/PJD6353s/PJD6383/PJD6383s/
PJD6653w/ PJD6683w only)
PJD6383s/PJD6553w/PJD6653w/PJD6653ws/
PJD66 w/PJD66 ws8383
PJD6683ws
only)
PJD6553w/ PJD6653ws/ /PJD6683ws
48
Main menu Sub-menu Options
4.
SYSTEM
SETUP:
Basic
Message On/Off
LAN Control
Settings
(PJD6223/PJD6253/
PJD6353/PJD6353s/
PJD6383/PJD6383s/
PJD6553w/
PJD6653w/
PJD6653ws/
PJD6683ws only)
DHCP On/Off
Projector IP Address
Subnet Mask
Default Gateway
DNS Server
Apply
Standby
Settings
Power Saving On/Off
Active VGA Out On/Off
Active Audio Out On/Off
Quick Power Off On/Off
5.
SYSTEM
SETUP:
Advanced
High Altitude Mode On/Off
DCR On/Off
Audio Settings
Mute On/Off
Volume
Menu Settings
Menu Display Time
5 sec/10 sec/15 sec/20 sec/
25 sec/30 sec
Menu Position
Center/Top-Left/Top-Right/
Bottom-Left/Bottom-Right
Closed Caption
Closed Caption
Enable
On/Off
Caption Version CC1/CC2/CC3/CC4
Lamp Settings
Lamp Mode Normal/Economic
Reset Lamp Timer
Equivalent Lamp
Hour
Presentation
Timer
Timer Period 1~240 minutes
Timer Display
Always/1 min/2 min/3 min/
Never
Timer Position
Top-Left/Bottom-Left/Top-
Right/Bottom-Right
Timer Counting
Direction
Count Down/Count Up
Sound Reminder On/Off
Start Counting/Off
Security
Settings
Change Password
Power On Lock On/Off
Remote Control Code A/B
Reset All Settings On/Off
PJD6683w
49
Main menu Sub-menu Options
6.
INFORMATION
Current System Status
Source
Color Mode
Resolution
Color System
Equivalent Lamp Hour
MAC Address (PJD6223/PJD6253/
PJD6353/PJD6353s/PJD6383/PJD6383s/
PJD6553w/PJD6653w/PJD6653ws/
PJD6683w only)
/PJD6683ws
50
Description of each menu
Function Description
Screen Color
Corrects the projected picture’s color when the projection surface
is not white. See "Using Screen Color" on page 33 for details.
Aspect Ratio
There are three options to set the image's aspect ratio depending
on your input signal source. See "Selecting the aspect ratio" on
page 30 for details.
Keystone
Corrects any keystoning of the image. See "Correcting keystone"
on page 29 for details.
Position
Displays the position adjustment page. To move the projected
image, use the directional arrow keys. The values shown on the
lower position of the page change with every key press you made
until they reach their maximum or minimum.
Phase
Adjusts the clock phase to reduce image
distortion.
H. Size
Adjusts the horizontal width of the image.
Zoom
Magnifies or reduces the projected image. See "Magnifying and
searching for details" on page 29 for details.
3D Sync
This projector features a 3D function which enables you to enjoy
the 3D movies, videos, and sporting events in a more realistic
way by presenting the depth of the images.
This function is not available when video source is detected
for the PJD5126/PJD5226/PJD5226w.
You need to wear a pair of 3D glasses to view the 3D images.
TI 3D DLP Link:
Enables projector for TI 3D DLP Link.
Off:
Disables 3D.
When the 3D Sync function is on:
The brightness level of the projected image will decrease.
The Color Mode cannot be adjusted.
The Keystone can only be adjusted within limited degrees.
The Zoom can only magnify the pictures to limited sizes.
3D Sync
Invert
When you discover the inversion of the image depth, enable this
function to correct the problem. (For TI 3D DLP Link only)
Color
Management
See "Color Management" on page 35 for details.
1. DISPLAY menu
51
Function Description
Color Mode
Pre-defined picture modes are provided so you can optimize your
projector image set-up to suit your program type. See "Selecting a
picture mode" on page 32 for details.
Reference
Mode
Selects a picture mode that most suits your need for the image
quality and further fine-tune the image based on the selections
listed on the same page below. See "Setting the User 1/User 2
mode" on page 33 for details.
Brightness
Adjusts the brightness of the image. See "Adjusting Brightness" on
page 34 for details.
Contrast
Adjusts the degree of difference between dark and light in the
image. See "Adjusting Contrast" on page 34 for details.
Color
Adjusts the color saturation level -- the amount of each color in a
video image. See "Adjusting Color" on page 34 for details.
Tint
Adjusts the red and green color tones of the image. See "Adjusting
Tint" on page 34 for details.
The function is only available when Video or S-Video with
NTSC system is selected.
Sharpness
Adjusts the image to make it look sharper or softer. See "Adjusting
Sharpness" on page 34 for details.
Brilliant
Color
Adjusts white peaking while maintaining correct color presentation.
See "Adjusting Brilliant Color" on page 34 for details.
Color
Temperature
See "Selecting a Color Temperature" on page 34 for details.
Save
Settings
Saves the settings made for the User 1 or User 2 mode.
2. PICTURE menu
52
Function Description
Quick Auto
Search
See "Switching input signal" on page 27 for details.
Color Space
Conversion
See "Changing Color Space" on page 27 for details.
DynamicEco
Timer
Allows the projector to decrease the power consumption
automatically if no input signal is detected after a set period of time.
It takes some time to initiate this function. Make sure the
projector has been turned on for more than 4 minutes.
Smart
Restart
Selecting On enables you to restart the projector immediately
within 150 seconds after turning it off. After 150 seconds, if the
projector is not turned on again, it will directly enter the standby
mode.
•It takes some time to initiate this function. Make sure the
projector has been turned on for more than 4 minutes.
If the projector is resumed by using the Smart Restart
feature, this function can be executed immediately.
•When On is selected, the Quick Power Off function will be
automatically set to “On”.
Pattern
The projector can display several test patterns. It helps you adjust
the image size and focus and check that the!projected image is free
from distortion.
Selecting User displays the picture you saved as Screen
Capture.
My Button
Sets a hotkey on remote control.
3. SOURCE menu
53
Function Description
Language
Sets the language for the On-Screen Display (OSD) menus. See
"Using the menus" on page 23 for details.
Projector
Position
The projector can be installed on a ceiling or behind a screen, or
with one or more mirrors. See "Choosing a location" on page 12
for details.
Auto Power
Off
Allows the projector to turn off automatically if no input signal
is detected after a set period of time. See "Setting Auto Power
Off" on page 57 for details.
Blank Timer
Sets the image blank time when the Blank feature is activated,
once elapsed the image will return to the screen. See "Hiding the
image" on page 37 for details.
Panel Key
Lock
Disables or enables all panel key functions except POWER
on the projector and keys on the remote control. See "Locking
control keys" on page 37 for details.
Splash
Screen
Allows you to select which logo screen will be displayed during
projector start-up.
Screen
Capture
Captures and stores the projected picture as Screen Capture.
See "Creating your own startup screen" on page 38 for details.
Message
Selecting On displays the current information on the screen
when the projector is detecting or searching for a signal.
LAN Control
Settings
See "Controlling the projector through a LAN environment" on
page 39 for details.
Standby
Settings
See "Using the projector in standby mode" on page 45 for
details.
High Altitude
Mode
A mode for operation in high altitude areas. See "Operating in a
high altitude environment" on page 37 for details.
DCR
Enables or disables the DCR (Dynamic Contrast Ratio) function.
Selecting On enables the function and the projector will
automatically switch the lamp mode between normal and
economic modes according to the input image detected.
This function is only available when a PC source is in use.
After enabling DCR, frequent lamp mode switching may
shorten lamp life and noise level will vary during operation.
4. SYSTEM SETUP: Basic menu
I
I
5. SYSTEM SETUP: Advanced menu
54
Function Description
Audio
Settings
The sound adjustments made as below will have an effect on the
projector speaker. Be sure you have made a correct connection to
the projector audio input/output jacks. See "Connection" on page
17 for more details.
Mute
Mutes the sound received from AUDIO IN 1 and AUDIO IN 2
(L/R).
Volume
Adjusts the sound level received from AUDIO IN 1 and AUDIO
IN 2 (L/R).
Menu
Settings
Menu Display Time
Sets the length of time the OSD will remain active after your last
key press. The range is from 5 to 30 seconds in 5-second
increments.
Menu Position
Sets the On-Screen Display (OSD) menu position.
Closed
Caption
Closed Caption Enable
Activates the function by selecting On when the selected input
signal carries closed captions.
Captions: An on-screen display of the dialogue, narration,
and sound effects of TV programs and videos that are closed
captioned (usually marked as "CC" in TV listings).
This function is only available when a Composite video or
S-Video input signal is selected and its system format is
NTSC.
Caption Version
Selects a preferred closed captioning mode. To view captions,
select CC1, CC2, CC3, or CC4 (CC1 displays captions in the
primary language in your area).
Lamp
Settings
Lamp Mode
See "Setting Lamp Mode as Economic" on page 57 for details.
Reset Lamp Timer
See "Resetting the lamp timer" on page 61 for details.
Equivalent Lamp Hour
See "Getting to know the lamp hour" on page 57 for details on
how the total lamp hour is calculated.
Presentation
Timer
Reminds the presenter to finish the presentation within a certain
time frame. See "Setting the presentation timer" on page 36 for
details.
5. SYSTEM SETUP: Advanced menu
55
Function Description
Security
Settings
See "Utilizing the password function" on page 24 for details.
Remote
Control Code
See "Remote control code" on page 9 for details.
Reset All
Settings
Returns all settings to the factory preset values.
The following settings will still remain: Phase, H. Size, User
1, User 2, Language, Projector Position, High Altitude
Mode, Security Settings.
Current
System
Status
Source
Shows the current signal source.
Color Mode
Shows the selected mode in the PICTURE menu.
Resolution
Shows the native resolution of the input signal.
Color System
Shows input system format, NTSC, PAL, SECAM, or RGB.
Equivalent Lamp Hour
Displays the number of hours the lamp has been used.
MAC Address
Shows the MAC Address of your projector.
MAC Address stands for Media Access Control Address,
which is a physical layer address used to uniquely identify
a network node.
5. SYSTEM SETUP: Advanced menu
6. INFORMATION menu
56
Maintenance
Care of the projector
Your projector needs little maintenance. The only thing you need to do on a regular basis is
to keep the lens clean.
Never remove any parts of the projector except the lamp. Contact your dealer if other parts
need replacing.
Cleaning the lens
Clean the lens whenever you notice dirt or dust on the surface.
Use a canister of compressed air to remove dust.
If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with lens
cleaner and gently wipe the lens surface.
CAUTION
Never rub the lens with abrasive materials.
Cleaning the projector case
Before you clean the case, turn the projector off using the proper shutdown procedure as
described in "Shutting down the projector" on page 45 and unplug the power cord.
To remove dirt or dust, wipe the case with a soft, lint-free cloth.
To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral pH
detergent. Then wipe the case.
CAUTION
Never use wax, alcohol, benzene, thinner or other chemical detergents. These can damage the
case.
Storing the projector
If you need to store the projector for an extended time, please follow the instructions below:
Make sure the temperature and humidity of the storage area are within the
recommended range for the projector. Please refer to "Specifications" on page 64 or
consult your dealer about the range.
Retract the adjuster feet.
Remove the battery from the remote control.
Pack the projector in its original packing or equivalent.
Transporting the projector
It is recommended that you ship the projector with its original packing or equivalent.
57
Lamp information
Getting to know the lamp hour
When the projector is in operation, the duration (in hours) of lamp usage is automatically
calculated by the built-in timer.
To obtain the lamp hour information:
1. Press MENU/EXIT on the projector or Menu on the remote control and then press
/ until the SYSTEM SETUP: Advanced menu is highlighted.
2. Press to highlight Lamp Settings and press MODE/ENTER on the projector or
ENTER on the remote control. The Lamp Settings page is displayed.
3. You will see the Equivalent lamp hour information on the menu.
4. To leave the menu, press MENU/EXIT on the projector or Exit on the remote
control.
You can also get the lamp hour information on the INFORMATION menu.
Extending lamp life
The projection lamp is a consumable item. To keep the lamp life as long as possible, you
can do the following settings via the OSD menu.
Setting Lamp Mode as Economic
Using Economic mode reduces system noise and power consumption by 20%. If the
Economic mode is selected, the light output will be reduced and result in darker projected
pictures.
Setting the projector in Economic mode also extends the lamp operation life. To set
Economic mode, go into the SYSTEM SETUP: Advanced > Lamp Settings > Lamp
Mode menu and press / .
Setting Auto Power Off
This function allows the projector to turn off automatically if no input source is detected
after a set period of time to prevent unnecessary waste of lamp life.
To set Auto Power Off, go into the SYSTEM SETUP: Basic > Auto Power Off menu and
press / . If the preset time lengths are not suitable for your presentation, select Disable.
The projector will not automatically shut down in a certain time period.
58
Timing of replacing the lamp
When the Lamp indicator lights up red or a message appears suggesting it is time to
replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a
malfunction in the projector and in some instances the lamp may explode.
CAUTION
The Lamp indicator light and Temperature warning light will light up if the lamp becomes too
hot. Turn the power off and let the projector cool for 45 minutes. If the Lamp or Temp indicator
still lights up after turning the power back on, please contact your dealer. See "Indicators" on
page 62 for details.
The following lamp warning displays will remind you to change the lamp.
Status Message
Install a new lamp for optimal performance. If the
projector is normally run with Economic selected
(See "Setting Lamp Mode as Economic" on page
57), you may continue to operate the projector
until the next hour lamp warning appears.
A new lamp should be fitted to avoid the
inconvenience when the projector runs out of lamp
time.
It is strongly recommended that you replace the
lamp at this age. The lamp is a consumable item.
The lamp brightness diminishes with use. This is
normal lamp behavior. You can replace the lamp
whenever you notice that the brightness level has
significantly diminished. If the lamp is not
replaced beforehand, it must be replaced when
you see this message.
The lamp MUST be replaced before the projector
will operate normally.
OK
Order Replacement Lamp
Lamp > ____ Hours
Notice
OK
Replace Lamp Soon
Lamp > ____ Hours
Notice
OK
Replace Lamp Now
Lamp > ____ Hours
Lamp usage time exceeded
Notice
OK
Lamp usage time exceeded
Replace lamp (refer to User Manual)
Then reset lamp timer
Notice
59
Replacing the lamp
To prepare a new lamp, contact your dealer and tell the lamp type number.
Type number:
Type number:
WARNING
Hg - Lamp contains mercury. Manage in accordance with local disposal
laws. See www.lamprecycle.org
To reduce the risk of electrical shock, always turn the projector off and disconnect the
power cord before changing the lamp.
To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes
before replacing the lamp.
To reduce the risk of injuries to fingers and damage to internal components, use caution
when removing lamp glass that has shattered into sharp pieces. Before replacing the
lamp, clean the lamp compartment and dispose of cleaning materials. Be careful of sharp
edges in the lamp compartment. Wash hands after lamp replacement.
Only ViewSonic certified lamps are tested with this projector. Use of other lamps may
cause electrical shock and fire.
1. Turn the power off and disconnect the
projector from the wall socket. If the
lamp is hot, avoid burns by waiting for
approximately 45 minutes until the
lamp has cooled.
2. Loosen the screws that secure the lamp
cover on the both sides of the projector
until the lamp cover loosens.
3. Remove the lamp cover from the
projector.
WARNING
Do not turn the power on with the lamp
cover removed.
Do not insert your fingers between the
lamp and the projector. The sharp edges
inside the projector may cause injuries.
4. Remove and dispose of the lamp
protection film.
1
2
Type number:
RLC-070
ņ
PJD5226w/PJD6223/PJD6353/PJD6353s/PJD6653w/PJD6653ws
RLC-077
ņ
PJD5126/PJD5226
Ň
RLC-071
ņ
PJD6253/PJD6383/PJD6383s/PJD6553w/PJD6683w/PJD6683ws
Ň
Ň
60
5. Loosen the screw that secures the lamp.
6. Lift the handle so that it stands up. Use
the handle to slowly pull the lamp out
of the projector.
CAUTION
Pulling it too quickly may cause the lamp
to break and scatter broken glass in the
projector.
Do not place the lamp in locations where
water might splash on it, children can
reach it, or near flammable materials.
Do not insert your hands into the projector
after the lamp is removed. If you touch the
optical components inside, it could cause
color unevenness and distortion of the
projected images.
7. Insert the new lamp into the lamp
compartment and make sure it fits in
the projector.
8. Tighten the screw that secures the lamp.
CAUTION
Loose screw may cause a bad connection,
which could result in malfunction.
Do not over tighten the screw.
9. Ensure the handle is fully laid flat and
locked in place.
61
13. Restart the projector.
CAUTION
Do not turn the power on with the lamp cover removed.
Resetting the lamp timer
14. After the startup logo, open the On-Screen
Display (OSD) menu.
15. Go to the SYSTEM SETUP: Advanced >
Lamp Settings menu. Press MODE/ENTER
on the projector or ENTER on the remote
control. The Lamp Settings page is
displayed.
16. Press to highlight Reset lamp timer and
press MODE/ENTER on the projector or
ENTER on the remote control. A warning
message is displayed asking if you want to
reset the lamp timer.
17. Highlight Reset and press MODE/ENTER
on the projector or ENTER on the remote
control. The lamp time will be reset to '0'.
CAUTION
Do not reset if the lamp is not new or replaced as this
could cause damage.
10. Place the lamp protection film supplied
with the new lamp on the lamp
compartment.
11. Replace the lamp cover on the
projector.
12. Tighten the screws that secure the lamp
cover.
CAUTION
Loose screw may cause a bad connection,
which could result in malfunction.
Do not over tighten the screws.
2
1
Reset Lamp Timer?
Reset
Cancel
Notice
62
Indicators
Light Status & Description
Power Temp Lamp
Power events
Blue
Flashing
Off Off
Stand-by mode
Blue Off Off
Powering up
Blue Off Off
Normal operation
Lamp events
Purple
Flashing
Off Red
The projector has shut down automatically. If you try to re-
start the projector, it will shut down again. Please contact
your dealer for assistance.
Off Off Red
1. The projector needs 90 seconds to cool down. Or
2. Please contact your dealer for assistance.
Thermal events
Off Red Off
The projector has shut down automatically. If you try to re-
start the projector, it will shut down again. Please contact
your dealer for assistance.
Off Red Red
Off Red Green
Red Red Red
Red Red Green
Blue Red Red
Blue Red Green
Purple Red Red
Purple Red Green
Off Green Red
63
Troubleshooting
The projector does not turn on.
No picture
Blurred image
Remote control does not work
Cause Remedy
There is no power from the power
cord.
Plug the power cord into the AC inlet on the
projector, and plug the power cord into the
power outlet. If the power outlet has a switch,
make sure that it is switched on.
Attempting to turn the projector on
again during the cooling process.
Wait until the cooling down process has
completed.
Cause Remedy
The video source is not turned on or
connected correctly.
Turn the video source on and check that the
signal cable is connected correctly.
The projector is not correctly
connected to the input signal device.
Check the connection.
The input signal has not been
correctly selected.
Select the correct input signal with the
SOURCE key on the projector or remote
control.
The lens cover is still closed. Open the lens cover.
Cause Remedy
The projection lens is not correctly
focused.
Adjust the focus of the lens using the focus
ring.
The projector and the screen are not
aligned properly.
Adjust the projection angle and direction as
well as the height of the projector if necessary.
The lens cover is still closed. Open the lens cover.
Cause Remedy
The battery is out of power. Replace the battery with a new one.
There is an obstacle between the
remote control and the projector.
Remove the obstacle.
You are too far away from the
projector.
Stand within 8 meters (26 feet) of the
projector.
64
Specifications
Projector specifications
All specifications are subject to change without notice.
General
Product name DLP Projector
Optical
Resolution PJD5126:
800 x 600 SVGA
:
1024 x 768 XGA
1280 x 800 WXGA
Display system 1-CHIP DMD
Lamp
180 W lamp
240 W lamp
Electrical
Power supply
AC100–240V, 2.9 A, 50/60 Hz (Automatic)
AC100–240V, 3.5 A, 50/60 Hz (Automatic)
Power
consumption 285 W (Max); < 1 W (Standby)
350 W (Max); < 1 W (Standby)
Mechanical
Weight
2.6 Kg (5.74 lbs)
2.99 Kg (6.6 lbs)
Not all models can be purchased in your region.
PJD5226/PJD6223/PJD6253/PJD6353/PJD6353s/PJD6383
PJD5226w/PJD6553w/PJD6653w/PJD6653ws/PJD6683w
/PJD6383s:
/PJD6383ws:
PJD5126/PJD
5
226/PJD5226w/PJD6223/PJD6353/
PJD6253/PJD6383/PJD6383s/PJD6553w/PJD6683w
PJD6353s/
PJD6653w/PJD6653ws:
/PJD6683ws:
PJD5126/PJD5226/PJD5226w/PJD6223/PJD6353/PJD6353s/PJD6653w/PJD6653ws:
PJD6253/PJD6383/PJD6383s/PJD6553w/PJD6683w/PJD6683ws:
PJD5126/PJD5226/PJD5226w/PJD6223/PJD6353/PJD6353s/PJD6653w/PJD6653ws:
PJD6253/PJD6383/PJD6383s/PJD6553w/PJD6683w/PJD6683ws:
PJD5126/PJD5226/PJD5226w/PJD6223/PJD6253/PJD6553w:
PJD6353/PJD6353s/PJD6383/PJD6383s/PJD6653w/PJD6653ws/PJD6683w/PJD6683ws:
65
Input terminal
Computer input
RGB input D-Sub 15-pin (female) x 2
Video signal input
S-VIDEO Mini DIN 4-pin port x 1
VIDEO RCA jack x 1
SD/HDTV signal
input
Analog – D-Sub <–> Component RCA jack x 3
(through RGB input)
Digital – PJD5126/PJD5226/PJD5226w:
N/A
HDMI V1.3 x 1
Audio signal input PC audio jack x 1 PC audio jack x 2
Output terminal
RGB output D-Sub 15-pin (female) x 1
Speaker PJD5126/PJD5226/PJD5226w:
2 watt x 1
10 watt x 1
Control terminal
RS-232 serial
control
9 pin x 1
LAN PJD5126/PJD5226/PJD5226w:
N/A
RJ45 x 1
USB serial control Type mini B
IR receiver PJD5126/PJD5226/PJD5226w:
x 1 (Front)
x 2!(Front and Top)
Environmental Requirements
Operating
temperature
0°C–40°C at sea level
Operating relative
humidity
10%–90% (without condensation)
Operating altitude 0–1499 m at 0°C–35°C
1500–3000 m at 0°C–30°C (with High Altitude Mode on)
PJD6223/PJD6253/PJD6353/PJD6353s/PJD6383/PJD6383s/PJD6553w/
PJD6653w/PJD6653ws/PJD6683w/PJD6683ws:
PJD6223/PJD6253/PJD6353/PJD6353s/PJD6383/PJD6383s/PJD6553w/
PJD6653w/PJD6653ws/PJD6683w/PJD6683ws:
PJD6223/PJD6253/PJD6353/PJD6353s/PJD6383/PJD6383s/PJD6553w/
PJD6653w/PJD6653ws/PJD6683w/PJD6683ws:
PJD6223/PJD6253/PJD6353/PJD6353s/PJD6383/PJD6383s/PJD6553w/
PJD6653w/PJD6653ws/PJD6683w/PJD6683ws:
66
Dimensions
294 mm (W) x 84 mm (H) x 242 mm (D) (Excluding extrusions)
Ceiling mount installation
TEMP
LMMP
MODE
ENTER
AUTO
SOURCE
MENU
EXIT
PJD5126/PJD5226/PJD5226w/
PJD6223/PJD6253/PJD6553w
TEMP
LMMP
MODE
ENTER
AUTO
SOURCE
MENU
EXIT
294
242
84
294
84
242
160
137
115
80
Ceiling mount screws:
M4 x 8 (Max. L = 8 mm)
Unit: mm
PJD6353/PJD6353s/PJD6383/PJD6383s/
PJD6653w/PJD6653ws/PJD6683w/PJD6683ws
67
Timing chart
Supported timing for PC input
Resolution
Horizontal!
Frequency
(kHz)
Vertical!
Frequency
(Hz)
Pixel!
Frequency
(MHz)
Mode
720 x 400 31.469 70.087 28.3221 720 x 400_70
640 x 480
31.469 59.94 25.175 VGA_60
37.861 72.809 31.5 VGA_72
37.5 75 31.5 VGA_75
43.269 85.008 36 VGA_85
61.91 119.518 52.5 VGA_120
800 x 600
37.879 60.317 40 SVGA_60
48.077 72.188 50 SVGA_72
46.875 75 49.5 SVGA_75
53.674 85.061 56.25 SVGA_85
30.998 49.916 30.75 SVGA_50
77.425 119.854 83 SVGA_120
1024 x 768
48.363 60.004 65 XGA_60
56.476 70.069 75 XGA_70
60.023 75.029 78.75 XGA_75
68.667 84.997 94.5 XGA_85
39.634 49.98 52 XGA_50
98.958 119.804 137.75 XGA_120
1280 x 800
49.702 59.81 83.5 WXGA_60
62.795 74.934 106.5 WXGA_75
71.554 84.88 122.5 WXGA_85
1280 x 1024
63.981 60.020 108.000 SXGA_60
79.976 75.025 135.000 SXGA_75
91.146 85.024 157.500 SXGA_85
1280 x 960 60 60 108 1280 x 960_60
1400 x 1050 65.317 59.978 121.75 SXGA+_60
1600 x 1200 75 60 162 UXGA
640 x 480@67Hz 35 66.667 30.24 MAC13
832 x 624@75Hz 49.722 74.546 57.28 MAC16
1024 x 768@75Hz 60.241 75.02 80 MAC19
1152 x 870@75Hz 68.68 75.06 100 MAC21
68
Supported timing for Component-YPbPr input
Displaying a 1080i(1125i)@60Hz or 1080i(1125i)@50Hz signal may result in slight image
vibration.
Supported timing for Video and S-Video inputs
Signal Format
Horizontal Frequency
(kHz)
Vertical Frequency (Hz)
480i(525i)@60Hz 15.73 59.94
480p(525p)@60Hz 31.47 59.94
576i(625i)@50Hz 15.63 50.00
576p(625p)@50Hz 31.25 50.00
720p(750p)@60Hz 45.00 60.00
720p(750p)@50Hz 37.50 50.00
1080i(1125i)@60Hz 33.75 60.00
1080i(1125i)@50Hz 28.13 50.00
1080P@60Hz 67.5 60
1080P@50Hz 56.26 50
Video mode
Horizontal
Frequency (kHz)
Vertical Frequency
(Hz)
Color sub-carrier
Frequency (MHz)
NTSC 15.73 60 3.58
PAL 15.63 50 4.43
SECAM 15.63 50 4.25 or 4.41
PAL-M 15.73 60 3.58
PAL-N 15.63 50 3.58
PAL-60 15.73 60 4.43
NTSC4.43 15.73 60 4.43
69
Copyright information
Copyright
Copyright 2011. All rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system or translated into any language or
computer language, in any form or by any means, electronic, mechanical, magnetic, optical,
chemical, manual or otherwise, without the prior written permission of ViewSonic
Corporation.
Disclaimer
ViewSonic Corporation makes no representations or warranties, either expressed or
implied, with respect to the contents hereof and specifically disclaims any warranties,
merchantability or fitness for any particular purpose. Further, ViewSonic Corporation
reserves the right to revise this publication and to make changes from time to time in the
contents hereof without obligation to notify any person of such revision or changes.
*DLP and Digital Micromirror Device (DMD) are trademarks of Texas Instruments. Others
are copyrights of their respective companies or organizations.
70
Appendix
IR control table
Code A
Key Format Byte1 Byte2 Byte3 Byte4
Power NEC 83 F4 17 E8
Freeze NEC 83 F4 03 fc
Up / KeyS + NEC 83 F4 0b f4
Down / KeyS - NEC 83 F4 0c f3
Left NEC83F40e f1
Right NEC 83 F4 0f f0
Color Mode NEC 83 F4 10 ef
Mute NEC83F414EB
Auto Sync NEC 83 F4 08 f7
Source NEC83F404 fb
Blank NEC 83 F4 07 f8
Menu NEC83F430CF
Enter / Mouse L
key
NEC83F415ea
Exit NEC 83 F4 28 D7
VGA 1 NEC 83 F4 41 be
VGA 2 NEC 83 F4 45 ba
Video/Mouse R
key
NEC83F452ad
Mouse NEC 83 F4 31 CE
Timer NEC83F427d8
Aspect NEC83F413EC
Magnify NEC 83 F4 32 CD
DynamicEco™ NEC 83 F4 2B D4
Pattern NEC83F455AA
My ButtonNEC83F456A9
Panel Key Lock NEC 83 F4 57 A8
Volume + NEC 83 F4 82 7D
Volume - NEC 83 F4 83 7C
PgUp NEC83F406F9
PgDn NEC 83 F4 05 FA
Info NEC 83 F4 97 68
PJD5126/PJD5226/PJD5226w/
PJD6223/PJD6353/PJD6353s
PJD6653w/PJD6653ws
PJD6253/PJD6383/PJD6383s/
PJD6683ws
PJ
D
655
3w/PJ D6683w
71
Code B
Key Format Byte1 Byte2 Byte3 Byte4
Power NEC83F4609F
Freeze NEC 83 F4 61 6E
Up / KeyS + NEC 83 F4 67 98
Down / KeyS - NEC 83 F4 68 97
Left NEC83F46996
Right NEC 83 F4 6A 95
Color Mode NEC 83 F4 9E 61
Mute NEC 83 F4 9D 62
Auto Sync NEC 83 F4 63 9C
Source NEC 83 F4 7D 82
Blank NEC 83 F4 62 9D
Menu NEC 83 F4 6C 93
Enter / Mouse L
key
NEC 83 F4 6B 94
Exit NEC 83 F4 6E 91
VGA 1 NEC 83 F4 64 9B
VGA 2 NEC 83 F4 65 9A
Video/Mouse R
key
NEC83F46699
Mouse NEC 83 F4 9B 64
Timer NEC 83 F4 9C 63
Aspect NEC 83 F4 9A 65
Magnify NEC 83 F4 99 66
DynamicEco™ NEC 83 F4 7F 80
Pattern NEC 83 F4 7E 81
My Button NEC 83 F4 6D 92
Panel Key Lock NEC 83 F4 5E A1
Volume + NEC 83 F4 5A A5
Volume - NEC 83 F4 5B A4
PgUp NEC 83 F4 5D A2
PgDn NEC 83 F4 5C A3
Info NEC 83 F4 5F A0
PJD5126/PJD5226/PJD5226w/
PJD6223/PJD6353/PJD6353s
PJD6653w/PJD6653ws
PJD6253/PJD6383/PJD6383s/
PJD6683ws
PJ
D
655
3w/PJ D6683w
72
RJ45 response table
The RJ45 commands can only be received via TCP port 4661.
Please refer to the below RS232 command table for the commands.
RS232 command table
<Pin assignment for this two end>
<Interface>
<RS232/RJ45 command table>
Status Response Response Code
Write
Normal => ACK 0x03 0x14 0x00 0x00 0x00 0x14
Incorrect => ERROR ACK 0x00 0x14 0x00 0x00 0x00 0x14
Timeout (>100ms) N/A
Status Response Code
Read
BYTE0 BYTE1 BYTE2 BYTE3 BYTE4 BYTE5 BYTE6 BYTE7~N BYTE N+1
0x05 0x14 0x00 LSB MSB 0x00 0x00 Data Checksum
Ex1. Read power status: 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x01 0x18 = On
Ex2. Read brightness: 0x05 0x14 0x00 0x04 0x00 0x00 0x00 0x32 0x00 0x4A = 50
Ex3. Read lamp hours: 0x05 0x14 0x00 0x06 0x00 0x00 0x00 0x28 0x00
0x00 0x00 0x42
= 40
Pin Description Pin Description
1NC2RX
3TX4NC
5GND6NC
7RTSZ8CTSZ
9NC
RS-232 protocol
Baud Rate 115200 bps (default)
Data Length 8 bit
Parity Check None
Stop Bit 1 bit
Flow Control None
Function Status Action cmd
Power
Write
Turn on 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x00 0x00 0x5D
Turn off 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x01 0x00 0x5E
Read
Power status
(on/off)
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x00
0x5E
73
Reset Execute 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x02 0x00 0x5F
Splash
Screen
Write
Splash
Screen Black
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x00 0x67
Splash
Screen Blue
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x01 0x68
Splash
Screen
ViewSonic
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x02 0x69
Splash
Screen
Screen
Capture
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x03 0x6A
Splash
Screen Off
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x04 0x6B
Read
Splash
Screen
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x0A
0x68
Quick
Power Off
Write
Quick Power
Off Off
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0B 0x00 0x68
Quick Power
Off On
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0B 0x01 0x69
Read
Quick Power
Off status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x0B
0x69
High
Altitude
Mode
Write
High Altitude
Mode Off
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0C 0x00 0x69
High Altitude
Mode On
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0C 0x01 0x6A
Read
High Altitude
Mode status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x0C
0x6A
Lamp Mode
Write
Lamp Mode
Normal
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x10 0x00 0x6D
Lamp Mode
Economic
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x10 0x01 0x6E
Read
Lamp Mode
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x10
0x6E
Message
Write
Message Off 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x27 0x00 0x84
Message On 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x27 0x01 0x85
Read
Message
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x27
0x85
74
Projector
Position
Write
Front Table 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x00 0x5E
Rear Table 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x01 0x5F
Rear Ceiling 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x02 0x60
Front Ceiling 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x03 0x61
Read
projector
position
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x00
0x5F
3D Sync
Write
OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x00 0x7E
TI 3D DLP
Link
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x01 0x7F
Read
3D Sync
Status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x20
0x7F
3D Sync
Invert
Write
Off 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x21 0x00 0x7F
On 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x21 0x01 0x80
Read
3D Sync
Invert Status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x21
0x80
Contrast
Write
Contrast
decrease
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x02 0x00 0x60
Contrast
increase
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x02 0x01 0x61
Read
Contrast
ratio
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x02
0x61
Brightness
Write
Brightness
decrease
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x03 0x00 0x61
Brightness
increase
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x03 0x01 0x62
Read Brightness
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x03
0x62
Aspect ratio
Write
Aspect ratio
Auto
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x00 0x62
Aspect ratio
4:3
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x02 0x64
Aspect ratio
16:9
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x03 0x65
Aspect ratio
16:10
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x04 0x66
Read Aspect ratio
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x04
0x63
Auto Adjust Excute 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x05 0x00 0x63
75
Horizontal
position
Write
Horizontal
position shift
right
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x06 0x01 0x65
Horizontal
position shift
left
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x06 0x00 0x64
Read
Horizontal
position
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x06
0x65
Vertical
position
Write
Vertical
position shift
up
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x07 0x00 0x65
Vertical
position shift
down
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x07 0x01 0x66
Read
read Vertical
position
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x07
0x66
Color
temperature
Write
color
temperature
T1
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x00 0x66
color
temperature
T2
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x01 0x67
color
temperature
T3
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x02 0x68
color
temperature
T4
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x03 0x69
Read
color
temperature
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x08
0x67
Blank
Write
Blank on 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x09 0x01 0x68
Blank off 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x09 0x00 0x67
Read Blank status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x09
0x68
Keystone-
Vertical
Write
Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0A 0x00 0x68
Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0A 0x01 0x69
Read
Keystone
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x0A
0x69
76
Color mode
Write
Brightest 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x00 0x69
Movie 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x01 0x6A
User 1 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x02 0x6B
User 2 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x03 0x6C
PC / Gaming 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x04 0x6D
ViewMatch 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x05 0x6E
Dynamic PC 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x06 0x6F
Dynamic
Movie
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x07 0x70
Read
Preset mode
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x0B
0x6A
Primary
Color
Write
Primary color
R
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x00 0x6E
Primary color
G
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x01 0x6F
Primary color
B
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x02 0x70
Primary color
C
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x03 0x71
Primary color
M
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x04 0x72
Primary color
Y
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x05 0x73
Read
Primary color
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x10
0x6F
Hue
Write
Hue
decrease
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x11 0x00 0x6F
Hue increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x11 0x01 0x70
Read Hue
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x11
0x70
Saturation
Write
Saturation
decrease
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x12 0x00 0x70
Saturation
increase
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x12 0x01 0x71
Read Saturation
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x12
0x71
77
Gain
Write
Gain
decrease
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x13 0x00 0x71
Gain
increase
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x13 0x01 0x72
Read Gain
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x13
0x72
Freeze
Write
Freeze on 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x00 0x01 0x60
Freeze off 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x00 0x00 0x5F
Read
Freeze
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x13 0x00
0x60
Source
input
Write
Input source
VGA
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x00 0x60
Input source
VGA2
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x08 0x68
Input source
Composite
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x05 0x65
Input source
SVIDEO
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x06 0x66
Input source
HDMI
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x03 0x63
Read Source
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x13 0x01
0x61
Quick Auto
Search
Write
Quick Auto
Search on
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x02 0x01 0x62
Quick Auto
Search off
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x02 0x00 0x61
Read
Quick Auto
Search
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x13 0x02
0x62
Mute
Write
Mute on 0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x00 0x01 0x61
Mute off 0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x00 0x00 0x60
Read Mute status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x14 0x00
0x61
Volume
Write
Increse
Volume
0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x01 0x00 0x61
Decrese
Volume
0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x02 0x00 0x62
Read Volume
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x14 0x03
0x64
78
Lamp Time
Write
Reset Lamp
usuage hour
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x01 0x00 0x62
Read
Lamp
usuage hour
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x15 0x01
0x63
Error status Read
Read error
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x0C 0x0D
0x66
79
Customer Support
For technical support or product service, see the table below or contact your reseller.
Note : You will need the product serial number.
Country/Region Web Site
T=Telephone
F=Fax
E-mail

Zealand
www.viewsonic.com.au


service@au.viewsonic.com
Canada www.viewsonic.com



service.ca@viewsonic.com

www.viewsoniceurope.
com

Hong Kong www.hk.viewsonic.com  service@hk.viewsonic.com
India www.in.viewsonic.com  service@in.viewsonic.com

www.viewsoniceurope.



service_ie@viewsoni
ceurope.com
Korea www.kr.viewsonic.com  service@kr.viewsonic.com


  soporte@viewsonic.com

(Chile)
  soporte@viewsonic.com

(Columbia)
  soporte@viewsonic.com


  soporte@viewsonic.com



   soporte@viewsonic.com
 www.hk.viewsonic.com  service@hk.viewsonic.com
  Contact your reseller service@ap.viewsonic.com

Islands
www.viewsonic.com



service.us@viewsonic.com
soporte@viewsonic.com

Thailand
www.viewsonic.com.sg  service@sg.viewsonic.com
  Contact your reseller service@ap.viewsonic.com
United Kingdom
www.viewsoniceurope.



service_gb@viewsoni
ceurope.com
 www.viewsonic.com



service.us@viewsonic.com
80
Limited Warranty
VIEWSONIC
®
PROJECTOR
What the warranty covers:

use, during the warranty period. If a product proves to be defective in material or workmanship during

Replacement product or parts may include remanufactured or refurbished parts or components.
Limited Three (3) year General Warranty






purchase.
Limited One (1) year Heavy Usage Warranty:
Under heavy usage settings, where a projectors use includes more than 





warranty information.


Who the warranty protects:
This warranty is valid only for the 
What the warranty does not cover:
1. 
2. 
 

with the product.
 
c. Operation of the product for other than the normal intended use or not under normal
conditions.
 
 
f. Removal or installation of the product.
 
 
81
 
 
3. 
How to get service:
1. 

2. To obtain warranted service, you will be required to provide (a) the original dated sales slip, (b)
your name, (c) your address, (d) a description of the problem, and (e) the serial number of the
product.
3. 

4. 
Limitation of implied warranties:


Exclusion of damages:

be liable for:
1. 

interference with business relationships, or other commercial loss, even if advised of the possibility
of such damages.
2. 
3. 
Effect of state law:



Sales outside the U.S.A. and Canada:







82
Mexico Limited Warranty
VIEWSONIC
®
PROJECTOR
What the warranty covers:


will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include

How long the warranty is effective:

consumer purchase.

only.

Who the warranty protects:

What the warranty does not cover:
 
 
 

 
 
 
 
 
 

 
How to get service:


information in the space provided below on your purchase for your future use. Please retain your receipt of proof of
purchase to support your warranty claim.
For Your Records
 
 
 

1. To obtain warranty service, you will be required to provide (a) the original dated sales slip, (b) your name, (c)
your address, (d) a description of the problem, and (e) the serial number of the product.
 
 
Limitation of implied warranties:


Exclusion of damages:

 

relationships, or other commercial loss, even if advised of the possibility of such damages.
 
 
 
83
Contact Information for Sales & Authorized Service (Centro Autorizado de Servicio) within Mexico:
Name, address, of manufacturer and importers:



NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO: 001.866.823.2004
Hermosillo:





Villahermosa:





Puebla, Pue. (Matriz):





Veracruz, Ver.:





Chihuahua


Chihuahua, Chih.


Cuernavaca





Distrito Federal:





Guadalajara, Jal.:






Guerrero Acapulco




Monterrey:






MERIDA:





Oaxaca, Oax.:






Tijuana:




FOR USA SUPPORT:






7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Viewsonic PJD6353 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Viewsonic PJD6353 in the language / languages: English as an attachment in your email.

The manual is 1,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Viewsonic PJD6353

Viewsonic PJD6353 User Manual - French - 91 pages

Viewsonic PJD6353 User Manual - Portuguese - 85 pages

Viewsonic PJD6353 User Manual - Spanish - 90 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info