652054

Viessmann 4532 Manual

4
Zoom out
Zoom in
Previous page
1/8
Next page
4
Hinter dem Buchstaben eines Ein- oder Ausfahr-
signales steht die Zier des Gleises, für welches
das Signal gilt.
Damit Sie Ihre Signale korrekt beschriften können,
liegt dem Signal eine Tafel mit selbstklebenden
Bezeichnungsschildern bei. Schneiden Sie das
gewünschte Schild aus, ziehen Sie die Schutzfo-
lie ab und kleben Sie es auf die Nummerntafel am
Mast des Signals (Abb. 2).
Viele weitere Informationen zum Thema Signale
nden Sie im Viessmann-Signalbuch, Art.-Nr. 5299.
4. Funktionskontrolle
Nehmen Sie das Signal vorsichtig aus der Verpa-
ckung. Führen Sie vor der Montage eine Funkti-
onskontrolle durch:
- Gelbes Kabel (ohne Markierung) an einem Pol
eines 16 V-Modellbahntransformators – z. B.
Viessmann Art.-Nr. 5200 – anschließen.
- Abwechselnd jeweils ein blaues Kabel mit dem
anderen Pol des Trafos verbinden. Niemals
die blauen Kabel gleichzeitig anschließen.
Das kann zur Zerstörung des Signals führen.
Blau mit roter Markierung:
Signal auf „Halt“ (Hp0), oberer Flügel waagerecht,
unterer Flügel senkrecht;
Blau mit grüner Markierung:
Signal auf „Fahrt“ (Hp1), oberer Flügel schräg
nach oben, unterer Flügel senkrecht;
Blau mit gelber Markierung:
Signal auf „Langsamfahrt“ (Hp2), beide Flügel
schräg nach oben.
5. Montage
1. Beschriften Sie das Signal (siehe Kapitel 3).
2. Sägen Sie an der Montagestelle ein Rechteck
mit den Maßen 30 x 15 mm (Abb. 3). Bohren
Sie dazu zuerst 4 Löcher mit 6 mm Durchmes-
ser. Verwenden Sie die Schablone aus Abb. 3.
3. Führen Sie die Anschlusskabel von oben durch
das Montageloch und stecken Sie dann das
Signal mit dem Antrieb voran hinein.
4. Befestigen Sie das Signal mit den beiliegenden
Schrauben.
After the letter of an entry or depature signal is the
number of the track for which the signal applies.
In order to label your signals correctly, adhesive
signs are supplied with the signal. Cut out the de-
sired sign and attach it to the signal box after re-
moving the protection foil (g. 2).
4. Checking the function
Remove the signal from the box carefully. Check
all functions before the installation:
- Connect the yellow cable (without marking) to
one of the terminals of a 16 V transformer (AC/
DC), e. g. Viessmann item-No. 5200.
- Connect each a blue cable alternately with the
other terminal of the transformer. Never con-
nect the blue cables at the same time to the
transformer. This may destroy the signal.
Blue with red marking:
Signal on “Stop” (Hp0), upper arm horizontal,
lower arm vertical.
Blue with green marking:
Signal on “Proceed” (Hp1), upper arm diagonal,
lower arm vertical.
Blue with yellow marking:
Signal on “Proceed slowly” (Hp2), upper and
lower arm diagonal.
5. Mounting
1. Label the signal (see chapter 3).
2. Saw a square rectangle of 30 mm x 15 mm at
the mounting place. First drill 4 holes of 6 mm
each in the corners. Use the pattern which is
shown in g. 3.
3. Insert the signal’s connection cables into the
hole. Then put the signal with the drive unit in
front into the hole.
4. Fix the signal to the baseboard with the
enclosed screws.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Viessmann 4532 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Viessmann 4532 in the language / languages: English, German as an attachment in your email.

The manual is 2,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info