785489

Victron Phoenix acculader 12 30 Manual

9
Zoom out
Zoom in
Previous page
1/96
Next page
8
victron energy
Adjustments with remote panel Phoenix
Charger Control
WARNING: Always check with your battery
supplier if the choosen charge characteristic
is suitable for your battery and application
•
Remove the frontplate and connect the
Phoenix Charger Control panel to the 8-pin
modular jack.
•
Disconnect battery, Voltage sense and
Temperature sense. A voltmeter is not required
but may be useful.
•
While switching on keep one of the
pushbuttons
⇑
&
⇓
pushed.
•
Release pushbutton.
•
The adjust knob on the remote panel controls
the adjust-mode; the LED’s on the charger
correspond with the knob as follows:
knob adjust mode charger LED’s
0% not impl. Failure
10% Bulk Failure Bulk
20% Absorption Failure Absorption
30% Float Failure Float
40% Rep. Abs. interval Failure Abs./Float
50% Rep. Abs. time Failure Bulk/Abs.
60% Max. Abs. time Failure Bulk/Float
70% Characteristic Failure Bulk/Abs./Float
80% Battery type Failure/Abs. Float
90% not impl. Failure
100% not impl. Failure
•
Push
⇑
for up and
⇓
for down.
•
LED indicators on remote panel read the
value as follows:
LED flashing = 1 step
LED on = 2 steps
1 bar flashing = 9 steps
Left bar is [step x10], right bar is [step x1].
To read the Float and Absorption adjustment the
lowest value in the table has to be added:
12 V models 24V models
Bulk 0 – 50 A/30A;step 1A
0 – 25 A / 16 A; step 1 A
Abs
12.00 – 16.00 V;
step 0.1 V 24.00 – 32.00 V;
step 0.1 V
Float 12.00 – 16.00 V;
step 0.1 V 24.00 – 32.00 V;
step 0.1 V
Rep. Abs. int. 0 – 45 days; step 1 day ; def.= 7 days
Rep. Abs. time 0 – 72 qu. of an hour; step 1 qu.; def = 4 qu.
Max. Abs. time or
Fixed Abs. time 1 – 8 hrs ; default = 4 hrs.
Characteristic 1 = Fixed: Fixed Abs. time. default = 4 hrs.
Rep. Abs. int. default = 1 day
Rep. Abs. time. default = 2 qu.
2 = Adaptive
3 = Adaptive with BatterySafe mode (default)
Battery type
default = 1
Abs. Volt
age Float Voltage /
Reduced Float
Max.Abs. time
0: User defined
1: Sonnenschein
Dryfit A200 gel 14.4 V 28.8 V 13.8 V/
13.0 V 27.6 V/
26.0 V 4 hrs.
2: Traction
(tubular plate) 15.0 V 30.0 V 13.8 V/
13.0 V 27.6 V/
26.0 V 6 hrs.
3: Semitraction
1
14.4 V 28.8 V 14.0 V/
13.0 V 28.0 V/
26.0 V 5 hrs.
4: Victory
1
14.8 V 29.6 V 14.0 V/
13.0 V 28.0 V/
26.0 V 5 hrs.
12V
model 24V
model 12V
model 24V
model
•
Turn the knob to another adjust-mode to store or
switch Off to escape.
•
Switch Off and On to start normal charging
sequence.
•
Replace the frontplate.
Warning: If the knob is not turned after an
adjustment the charger will not store this
adjustment. If the Float or Absorption voltage
was adjusted and the charger is not switched off
this voltage will remain on the outputs.
1
The optimum absorption voltage of flat plate lead acid batteries depends on mechanical and chemical properties. Batteries with high antimony
doping can general be charged with a lower absorption voltage than batteries with low antimony doping, like the Victory carbon fibre battery.
(See the book "Electricity on board" at www.victronenergy.com )
30
Float voltage =
12+(1x1)+(4x0.2)= 13.8 volts (12V model)
24+(1x1)+(4x0.2)= 25.8 volts (24V model)
50
Repeated Absorption time =
4 quarters of an hour
70
Characteristic =
1. Fixed mode
40
Repeated Absorption interval
= 7 days
20
Absorption voltage =
12+(1x2)+(2x0.2)= 14.4 volts (12V model)
24+(1x2)+(2x0.2)= 26.4 volts (24V model)
60
Maximum Absorption time =
4 hrs.
80
Battery type =
1. Gel
10
Max. Bulk current =
25 amps
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Victron Phoenix acculader 12 30 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Victron Phoenix acculader 12 30 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian as an attachment in your email.

The manual is 1.81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info