785215

Victron Lynx Shunt VE.Can Manual

3
Zoom out
Zoom in
Previous page
1/6
Next page
2020-01-13 03:06 3/6 Lynx DC distribution system
Victron Energy - https://www.victronenergy.com/live/
Q - Is there a way of setting the battery instance?
A - There is a program available to change this but as the default is 0, which is the same as what a
CCGX reads we would not advise changing this!!
Further Questions and Answers about the Lynx Shunt are available on the Victron Community topic.
Lynx Distributor
Contains a positive and negative bus-bar and provides a connection for 4 individual DC equipment
circuits, loads or DC groups. It has a space for individual DC fuses per DC group.
There is an optional feature of an LED for each fuse to indicate if fuse is blown.
If you wish to use the fuse indication LEDs on the Lynx Distributor, it also requires a connection to a
Lynx Shunt. The Lynx Shunt contains the necessary wide input (8 to 70VDC) power supply to output
the required 5V (4,5V-5,5V) power requirement of the Lynx Distributor circuit board.
RJ11 fly leads are used to connect the Lynx Shunt to the Distributor. This RJ11 cable is supplied with
the Distributor in the box. There are two ports on the Lynx Shunt, and it is possible to use either.
When all is OK, only the central LED is green; when a fuse has blown (or is missing) the central and
blow fuse circuit LEDs turn red. If you are not using all connection points in your DC distribution, it
may be necessary to fit dummy fuses to extinguish the red LEDs.
A future upgrade is planned to also send info back to the GX device over the VE-can, but is not yet
implemented.
Fuses
Uses MEGA fuses. Please note that some MEGA fuses are only rated to 36Volt (suitable for 24V
systems), You must use 58/64V rated fuses for 48V systems.
Installation
Connectors and dip-switches:
The R11 connector is to power the Lynx-distributor from the Lynx-shunt
The DIP switch on the Lynx-distributor are for specific manual settings, to do with our 24V
batteries. Please don’t touch.
The 6-pin header block on the Lynx Distributor is for reading out the fuses, but this feature is
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Victron Lynx Shunt VE.Can at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Victron Lynx Shunt VE.Can in the language / languages: English as an attachment in your email.

The manual is 7.16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info