Manual Victron Digital Multi Control 200A (page 7 of 71) (English, German, Dutch, French, Spanish)

785209

Zoom out

Zoom in

1/71

3. Description of the Digital Multi Control panel

The DMC is a remote panel designed to work with all Multis/Quattro’s and Multi/Quattro systems.

This includes stand alone, parallel and 2-3 phase configurations. Both VE.Bus and non VE.Bus

systems are supported.

With the DMC a separate shore current and generator current can be set.

When used in an extended VE.Bus system one can even set up to 4 different shore currents.

For VE.Bus systems, the DMC will automatically adapt the adjustable range to match with the

connected system.

3.1 Generator support

The DMC provides a means to change the AC input current limit when the AC source is switched

externally from shore to generator.

Normally the DMC will send the shore current set point as determined by the knob to the

connected devices. If however the terminals of the screw connector on the backside of the DMC

are short circuited the DMC sends a preconfigured shore limit to the connected devices.

This preconfigured limit is generally used for a generator. The display on the DMC will therefore

show: .

The two terminals of the screw connector are to be connected to an externally controlled switch.

Normally spoken this will be an auxiliary relay of an external transfer switch.

3.2 Connecting VE.Bus devices

Using the DMC with VE.Bus devices is straightforward. Just connect the DMC to the system. The

maximum/minimum shore currents which can be set are automatically adapted to the system.

This means that:

- Connecting the DMC to one Multi with 16A feed through capacity will limit the maximum shore

setting to 16A.

- Connecting the DMC to five of these Multis in parallel will result in 80A as maximum shore limit.

(If needed, an upper limit can be set to prevent the operator from setting a too high shore limit.

(See section 6.4)

The DMC is capable of dealing with a Quattro or an extended VE.Bus system which has more

than 1 AC input. When the system switches over from one AC input to another, the DMC switches

too, setting the current limit to the last used value for that AC input.

In the Multi/Quattro configuration it is possible to indicate that a shore current limit is not to be

overruled by the remote panel. In such a case the DMC will not display a shore current limit value

but it will display the AC input identification as , , or .

If, in a system with more than 1 input, the corresponding input does allow changing by the remote

panel, the DMC will display the shore current value and the AC input identification alternating.

Exception to this is AC input 1. If AC input 1 is active only the shore current value will be

displayed and not the AC input identification.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Victron Digital Multi Control 200A in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 0.41 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Victron Digital Multi Control 200A Manual

Product: