785208

Victron Digital Multi Control 200 Manual

6
Zoom out
Zoom in
Previous page
1/71
Next page
3
EN NL FR DE ES Appendix
2.2.3 VE.Bus Multi system + external transfer switch (PowerMan)
If an external transfer switch is placed before the Multis then this switch determines which AC
source is used. The Multis do not have any information about the state of the switch. The DMC
provides a way to specify different shore limits for both AC sources.
To achieve this, the DMC must have information about the state of the external transfer switch.
For this purpose a screw connector is placed at the backside of the DMC.
Normally the DMC will send the shore current set point as determined by the knob to the Multis.
If however the terminals of this screw connector are short circuited the DMC sends a
preconfigured shore limit to the Multis. The display on the DMC will then show: .
The two terminals of the screw connector are to be connected to the PowerMan. An auxiliary
relay of the external transfer switch is the normal place. Refer to the transfer switch manual for
more information.
Refer to chapter 4 for a description on how to connect the DMC to the system.
For this application, the DMC has to be configured because it must “know” the current limit it
should send to the Multis when the terminals are short circuited. Please change the “Generator
current limit” parameter as needed. Refer to chapter 6 for a description of how to do this.
If you want to limit the maximum current the operator can set, you can change the “Upper
shore limit for AC input 1” parameter. Refer to chapter 6 for a description of how to do this.
2.3 Non VE.Bus system with 1 AC source
The DMC must be scaled (matched to the system) when it is used with non VE.Bus systems.
This can be done by changing the “scaling factor” parameter. Refer to the configuration
chapter for a description of how to do this.
After correct scaling the maximum current limit the operator can set is equal to the maximum limit
of the system. If you want to limit the maximum current the operator can set, you have to adapt
the “Upper shore limit for AC input 1” setting. Refer to the configuration chapter for a description
of how to do this.
2.4 Non VE.Bus system with 2 AC sources
The DMC must be scaled (matched to the system) when it is used with non VE.Bus systems. This
can be done by changing the “scaling factor” parameter. Refer to chapter 6 for a description of
how to do this.
A non VE.Bus system with 2 AC sources can only be build with an external transfer switch
(PowerMan). Installation is exactly the same as when using a VE.Bus system with an external
transfer switch so please refer to paragraph 2.2.3.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Victron Digital Multi Control 200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Victron Digital Multi Control 200 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 0.41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info