785457
26
Zoom out
Zoom in
Previous page
1/27
Next page
Last update: 2018-08-21 10:10 ccgx:start https://www.victronenergy.com/live/ccgx:start
https://www.victronenergy.com/live/ Printed on 2018-08-21 11:59
New for Off-grid systems only (for ESS systems this was already happening): setting up charge
voltages in VEConfigure is no longer necessary: the Multis, Quattros and also MPPT Solar
Chargers will charge with the voltage as received via CAN-bus from the battery.
3.4 Features for ESS
Fix keep batteries charged.
Change the solar offset from a variable 2V to a fixed 0.4V. These values are for 48V systems,
divide by 4 for 12V. This fixes over voltage warnings and shut-downs as seen on several
systems with CAN-bus BMSes. Note that this solar offset is only used by the system when ESS-
mode is set to Optimized in combination with the Feed-in excess solar charger
power-setting enabled, or when ESS-mode is set to Keep batteries charged.
Add Auto-recharge feature for the ESS Modes Optimized and Optimized (with
BatteryLife). The system will automatically recharge the battery (from the grid) when the
SOC drops 5% or more below the value of ‘Minimum SOC’ in the ESS menu. Recharge stops
when it reaches the Minimum SOC.
ESS improved state display: In addition to the charger states (Bulk/Absorption/Float), additional
Discharging and Sustain modes were added. In addition it also shows reasons for the state
it is in:
#1: SOC is low
#2: BatteryLife is active
#3: BMS disabled charging
#4: BMS disabled discharge
#5: Slow Charge in progress (part of BatteryLife, see above)
#6: User configured a charge limit of zero.
#7: User configured a discharge limit of zero.
4 More information resources
CCGX Genset start/stop
CCGX Frequently asked questions
CCGX Firmware upgrade to v2.00 or later
CCGX Manually updating firmware
CCGX Remote VEConfigure and remote firmware updates
CCGX Datasheet
CCGX & Fischer Panda generators
VRM Portal
VRM Portal - trouble shooting Remote Console
Venus OS - Beta testing
Open source
DISQUS Comments
View the discussion thread.
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Victron Color Control GX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Victron Color Control GX in the language / languages: English as an attachment in your email.

The manual is 0.97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info