785236
9
Zoom out
Zoom in
Previous page
1/59
Next page
Connect the Cerbo GX to the socket labelled ‘MultiPlus/Quattro’, or to one of the Multis/Quattros in the system. Do not connect
it to the Remote panel socket on the VE.Bus BMS.
Note that it will not be possible to control the On/Off/Charger Only switch. This option is automatically disabled in the Cerbo GX
menu when a VE.Bus BMS is used. The only way to control a Multi or Quattro when used with a VE.Bus BMS is to add a Digital
Multi Control to the system. Setting the input current limit is possible in systems with a VE.Bus BMS.
Combining MultiPlus/Quattro with a VE.Bus BMS and a Digital Multi Control is possible. Simply connect the Digital Multi Control
to the RJ-45 socket on the VE.Bus BMS labelled Remote panel.
To allow auto-power-down in the Cerbo GX in case of a low battery, make sure the Cerbo GX is powered via the VE.Bus BMS:
connect Power in V+ on the Cerbo GX to Load disconnect on the VE.Bus BMS. And connect both negative leads to the nega-
tive stub of a common Battery.
Combining the Cerbo GX with a Digital Multi Control
It is possible to connect both a Cerbo GX and a Digital Multi control to a VE.Bus system. The ability to switch the product On, Off
or set it to Charger Only via the Cerbo GX will be disabled. The same applies to the input current limit: when there is a Digital
Multi Control in the system, the input current limit which is set at that control panel will be the master-setting, and changing it on
the Cerbo GX will not be possible.
Connecting multiple VE.Bus systems to a single Cerbo GX
Only one VE.Bus system can be connected to the VE.Bus ports on the back of the Cerbo GX. The professional way to to monitor
more systems is to add a second Cerbo GX
If you do require to connect more than one system to the same Cerbo GX, use an MK3-USB. Functionality will be limited:
Only the system connected to the built-in VE.Bus ports is used to generate the data on the Overview pages.
All connected systems will be visible on the Device-list
All connected systems will be taken into account for Energy consumption and distribution calculations (kWh graphs on VRM)
Only the system connected to the built-in VE.Bus ports is used for the Generator start/stop logic
In case of an ESS system, only the system connected to the built-in VE.Bus ports is used in the ESS mechanisms. The other
one is displayed in the device list only.
Alternatively the VE.Bus to VE.Can interface (ASS030520105) can be used. Add one for each additional system. Note that we
advise against it; this interface is a deprecated product. Make sure that the VE.Can network is terminated and powered. For pow-
ering the VE.Can network, see Q17 in our data communication whitepaper.
2.4.2. Battery Monitor BMV-700 series; and MPPTs with a VE.Direct port
Either one or two compatible products can be connected directly to the Cerbo GX using a standard VE.Direct cable. There are
two types of VE.Direct cable available:
1. Straight VE.Direct cables, ASS030530xxx
2. VE.Direct cables with an angled connector on one end. These are designed to minimize the required depth behind a panel,
ASS030531xxx
VE.Direct cables have a maximum length of 10 metres. It is not possible to extend them. If longer lengths are required, use a
VE.Direct to USB adapter with an active USB extension cable.
It is also possible to use the VE.Direct to VE.Can interface, but note that this only works for BMV700 and BMV702. Not for the
BMV712, MPPT solar chargers and Inverters with a VE.Direct port. See next paragraph for more information on that VE.Can in-
terface.
Connecting more than two devices to your Cerbo GX using VE.Direct
First of all, note that the maximum of VE.Direct devices that can be connected, regardless of the interface is limited. How they are
connected, either direct, via USB or via CAN, does not change the maximum. See here for the maximum connected device limits.
Select the correct GX device for the number of connected devices required by the system.
Option 1: Use the VE.Direct to USB interface. The Cerbo GX has built-in USB ports (see Overview of Connections [5]). Use a
USB-hub when additional USB ports are required.
Option 2: The BMV700 and BMV702 can also be connected using the VE.Direct to VE.Can interface. Note that the BMV712,
MPPTs and VEDirect Inverters cannot be connected using this canbus interface as it does not translate the data into canbus
messages. When using the VE.Direct to VE.Can interface, make sure that the VE.Can network is terminated, and also pow-
ered. For powering the VE.Can network, see Q17 in our data communication whitepaper.
Notes about older VE.Direct MPPTs
An MPPT 70/15 needs to be from year/week 1308 or later. Earlier 70/15s are not compatible with the Cerbo GX, and unfortu-
nately upgrading the MPPT firmware will not help. To find the year/week number of your model, look for the serial number
which is printed on a label on its back. For example number HQ1309DER4F means 2013, week 09.
2.4.3. Skylla-i, Lynx Shunt VE.Can, Lynx Ion + Shunt and MPPTs with a VE.Can port
To connect a product with a VE.Can port, use a standard RJ45 UTP cable. (Available with straight and elbow connectors)
Cerbo GX Manual
9
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Victron Cebro GX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Victron Cebro GX in the language / languages: English as an attachment in your email.

The manual is 5.1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info