785214

Victron batterij monitor BMV 700H Manual

24
Zoom out
Zoom in
Previous page
1/334
Next page
22
04. Charged detection time
This is the time the charged-parameters (Charged Voltage and Tail Current) must be met
in order to consider the battery fully charged.
Default Range Step size
3 minutes 1 – 50 minutes 1 minute
______________________________________________________________
05. Peukert exponent
When unknown it is recommended to keep this value at 1,25 (default) for lead acid batteries
and change to 1,05 for Li-ion batteries. A value of 1,00 disables the Peukert compensation.
Default Range Step size
1,25 1 – 1,5 0,01
______________________________________________________________
06. Charge Efficiency Factor
The Charge Efficiency Factor compensates for the Ah losses during charging.
100% means no loss.
Default Range Step size
95% 50 – 100% 1%
______________________________________________________________
07. Current threshold
When the current measured falls below this value it will be considered zero.
The current threshold is used to cancel out very small currents that can negatively affect the long term
state-of-charge readout in noisy environments. For example if the actual long term current is 0,0A and due
to injected noise or small offsets the battery monitor measures -0,05A, and in the long term the BMV can
incorrectly indicate that the battery needs recharging. When the current threshold in this example is set to
0,1A, the BMV calculates with 0,0A so that errors are eliminated.
A value of 0,0A disables this function.
Default Range Step size
0,1A 0 – 2A 0,01A
______________________________________________________________
08. Time-to-go averaging period
Specifies the time window (in minutes) that the moving averaging filter works.
A value of 0 disables the filter and gives an instantaneous (real-time) readout; however the displayed value
may fluctuate heavily. Selecting the longest time (12 minutes) ensures that only long term load fluctuations
are included in the time-to-go calculations.
Default Range Step size
3 minutes 0 – 12 minutes 1 minute
_______________________________________________________________
09. Zero current calibration
If the BMV reads a non-zero current even when there is no load and the battery is not being
charged, this option can be used to calibrate the zero reading.
Ensure that there really is no current flowing into or out of the battery (disconnect the cable
between the load and the shunt), then press SELECT.
_______________________________________________________________
10. Synchronize
This option can be used to manually synchronize the BMV.
Press SELECT to synchronize.
The BMV can also be synchronized when in normal operating mode by holding the + and – buttons
simultaneously for 3 seconds.
.
… 24 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Victron batterij monitor BMV 700H at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Victron batterij monitor BMV 700H in the language / languages: English, German, Dutch, French, Italian, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 2.06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info