Manual Vibiemme Domobar Super (page 37 of 44) (English)

783524

Zoom out

Zoom in

1/44

27) Remove the reservoir ad the reservoir platform, remove the two screws holding the divider panel, tip the

panel back, and replace the autoﬁll sensor wire on the boiler.

CAUTION: Failure to replace the autoﬁll wire will cause your Vibiemme Domobar to behave errati-

cally and can cause damage to the machine not covered by the warranty.

28) Move the internal partition panel back into place and fasten with the two upper Phillips head screws.

29) Tip the machine onto its back and install the two small Phillips head screws in the bottom that hold the inter-

nal partition.

30) Place the machine upright and replace the outer cover and fasten the 6 Phillips head screws that hold it in

place. Take care not to pinch the two hoses that go into the water reservoir.

31) Replace the water reservoir platform, the water reservoir, reinstall the water softener if so equipped, wipe the

two hoses clean and replace them in their proper locations in the reservoir. Reﬁll the water reservoir with the

water normally used in the machine. If you found heavy deposits of minerals were removed from the machine

during the de-scaling process, think seriously about using a different source for your water or a different treat-

ment of the water. Also check the hardness of your water at more frequent intervals.

32) Plug the machine back in and turn the Power Switch to Position I. The pump should not start. P

lace a suitable

container under the hot water wand and open the hot water valve.

Turn the switch to Position II. As the machine

heats up some of the excess water in the boiler will be displaced by the steam. When the pump begins to oper-

ate signifying that water has been lowered to about the correct level, close the hot water tap. The pump should

stop shortly after closing the tap.

WARNING: Do not leave the machine unattended until the proper water level in the boiler has been veriﬁed!

33) When the machine comes up to temperature, bleed steam off the boiler to assure that the water level is correct.

If a lot of water comes out then the water level is too high. Repeat Step 32. If this problem continues, consult

your retailer/reseller.

33) Now that the machine is up to temperature, ﬂush a good amount of clean water through the hot water wand,

bleed some steam out of the steam wand, and run the brew cycle to clear about four to six ounces of water

through the grouphead to be sure they are clear of de-scaling agent. Save a few ounces of water and when it

cools, taste it. If the water tastes like the acid used in the cleaning agent, repeat the ﬂush process until the water

is free from the acidic taste of the de-scaler.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Vibiemme Domobar Super in the language / languages: English as an attachment in your email.

The manual is 4.39 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Vibiemme Domobar Super Manual

Product: