815509

Vermont Castings Intrepid - Gas Manual

50
Zoom out
Zoom in
Previous page
1/64
Next page
5050 3-90-30007474Vermont Castings • Intrepid DV-IFT Owner’s Manual_R28 • 11/23
Your Intrepid DV Gas Heater will provide years of service with
minimal upkeep. The following procedures will help ensure
that your stove continues to function properly.
A. Annual System Inspection
Have the entire heater and venting system inspected annually
by a qualied gas technician. Replace any worn or broken
parts.
B.Logset&Burner/CleaningandInspection
Cleanliness is critical to the proper function of the heater.
The logset and burner must all be kept free of dust and
unobstructed by debris. Inspect these areas before each use
and clean as necessary.
1. Turn the burner OFF and let the heater cool completely
before cleaning.
2. Remove the safety barrier and lift the stove front up and
then swing the bottom out to disengage it from the heater
shell.
3. Carefully remove the glass and frame assembly and
place it out of the way on a at, padded surface such as
a counter protected by a towel.
4. Carefully inspect the Logs for damage. Contact your
local dealer if any damage is evident.
5. Use a soft bristled brush to sweep dust or debris from the
Logs, Pilot and Burner. Use care as the logs are fragile
and susceptible to damage.
6. Replace the glass panel and frame assembly.
7. Replace the stove front and safety barrier.
C. Care of Cast Iron
An occasional dusting with a dry rag will help keep the painted
surfaces looking new. Use high-temperature stove paints,
available through your local dealer, to touch-up areas as
needed. Clean areas to be painted with a wire brush and be
sure to cover the logs, burner and valve assembly, glass and
frame assembly. Apply the paint sparingly; two light coats of
paint will give better results than a single heavy coat.
Clean porcelain enamel surfaces with a soft, damp cloth.
Do not use abrasive cleaning agents. If necessary, use only
a cleaning agent formulated especially for use on porcelain
enamel surfaces.
D. Glass Cleaning and Replacement
It will be necessary to clean the glass periodically. During
start-up, condensation, which is normal, forms on the inside of
the glass and causes lint, dust and other airborne particles to
cling to the glass surface. Also initial paint curing may deposit
a slight lm on the glass. It is therefore recommended that
the glass be cleaned two or three times with a non-ammonia
household cleaner and warm water (we recommend gas
stove glass cleaner). Allow the glass to cool completely before
attempting to clean. To access the glass, remove the front and
glass frame, Figures 5.1 and 5.2. After that the glass should
be cleaned two or three times during each heating season
depending on the circumstances present.
NOTE:Cleanglassafterrsttwoweeksofoperation.
Glass Replacement
Replace glass only with HHT approved parts. Refer to Section
7 “Service Parts List” for correct glass. Remove the front,
glass frame and glass panel, Figures 5.1 & 5.2. Use a razor
blade to separate the glass and gasket from the frame.
CAUTION
!
Turn the pilot o󰀨 before painting. Allow the heater to cool
completely before painting.
5 5 Cleaning and Maintenance
Figure 5.1 - Remove the stove front.
ST967a
Remove Front
7/07
Figure 5.2 - Release the latches to remove the glass frame.
ST391a
Pinnacle
release latches
6/00
NOTE: Shown without top for clarity.
… 50 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vermont Castings Intrepid - Gas at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vermont Castings Intrepid - Gas in the language / languages: English as an attachment in your email.

The manual is 17.23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info