815502
20
Zoom out
Zoom in
Previous page
1/28
Next page
Vermont Castings • Dauntless FlexBurn Owner’s Manual_R17 • 2020 - ___ • 09/23 203-90-586000C
4 4 Troubleshooting Guide
Withproperinstallation,operation,andmaintenanceyourwoodappliancewillprovideyearsoftrouble-freeservice.Ifyoudo
experienceaproblem,thistroubleshootingguidewillassistyouoraqualiedservicepersoninthediagnosisofaproblem
and the corrective action to be taken.
Contact your dealer for additional information regarding operation and troubleshooting.
Visit www.vermontcastings.com to locate a dealer.
Start Fire Problems Possible Cause Solution
•Cannotgetrestarted
• Excessive smoke spillage
• Burns too slowly
• Not enough heat output
Not enough kindling/paper or no
kindling/paper
Use dry kindling, more paper. Arrange
kindling&woodforairmovement.
Notenoughairforretoignite
Check for restricted termination cap
Checkforblockageofoutsideairkit(if
installed).
Checkforueblockage.
Pre-warmuebeforestartingre(refer
toBuildingaFireSection).
Checkforadequateventheight(refer
toChimneyHeightSection).
Refer to Negative Pressure section
Wood condition is too wet, too large Use dry, seasoned wood (refer to
SeasonedWoodSection).
Bed of coals not established before
adding wood
Startwithpaper&kindlingtoestablish
bed of coals (refer to Building a Fire
Section).
Flue blockage such as birds’ nests or
leaves in termination cap
Have chimney inspected for creosote
and cleaned by a certied chimney
sweep.
Down draft or negative pressure
Competition with exhaust devices
Donotuseexhaustfansduringstart-up
(refertoNegativePressureSection).
Fire burns too fast
Extremely dry or soft wood
Mix in hardwood.
Mixinlargerpiecesofwoodafterreis
established.
Overdrafting
Check for correct vent height; too much
vertical height creates overdrafting.
Check location of vent termination
(refer to Chimney Termination
RequirementSection).
LowHeatOutput Coal Bed too small
Open damper. Establish deeper coal
bed and move coals to the rear of the
rebox.
Excessive Coal Bed Operatingonhighforextendedperiods Reduce burn rate and allow coals to
burn down before reloading.
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vermont Castings Dauntless FlexBurn at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vermont Castings Dauntless FlexBurn in the language / languages: English as an attachment in your email.

The manual is 8.21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Vermont Castings Dauntless FlexBurn

Vermont Castings Dauntless FlexBurn User Manual - French - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info