578266

Vermeiren Eclips plus Manual

15
Zoom out
Zoom in
Previous page
1/152
Next page
Eclips+, Eclips+ 30°
2011-05
Page 13
2.14 Pushing pole
L WARNING: Risk of injury - Make sure that all screws are properly tightened with
the appropriate tool.
L WARNING: Risk of injury - When equipped with the pushing pole, the pushing
pole shall always be mounted (→ to increase the stability of the back).
Back-adjustable wheelchair Eclips+30° comes with pushing pole fitted as standard (on the
Eclips + for the seat widths of 500 and 550 mm (19.69 in. and 21.65 in.)). The pushing pole
increase the stability of the back and offer you the possibility of pushing the wheelchair by an
attendant. To do this, use the pre-mounted handles.
As there are different pushing poles for different seat widths, take care that no tension
between the pushing handles of the back tubes is created.
The mounting of the push pole is done as follows:
1. Secure the pushing pole by fastening the left
side to the end of back tube handle with the
Philips screw in the applicable sunk threads.
2. Screw gently the Philips screw on the right
hand side into the thread of the back tube.
3. Swing the push pole to the right.
4. Hook the suspension of the pushing pole over
the screw thread.
When this is difficult it is possible that the push
pole is too long. Place the push pole on the left-
hand-grip with the Philips screw in the hole
most to the right.
To take off the push pole:
1. Loosen the Philips screw on the right hand-grip.
2. Remove the hook from the right hand-grip.
2.15 Back adjusting (Eclips+ 30°)
L WARNING: Risk of tipping over – Be aware that the stability decrease when
adjust the back backwards.
L WARNING: Risk of injury – Tighten the parking brakes before adjusting the back.
With the model Eclips+ 30° it is possible to set the back backwards with a maximum
inclination of 30°. Be sure that the patient sits in the chair when the attendant shall perform
the back adjusting and that the wheelchair does not tip over.
1. Pull handle on both sides towards the grab
handle to adjust the back rest.
2. Pull both back tubes backwards continuously
to a maximum inclination of 30°.
3. The gas pressure spring shall be pressed in.
To set the back to a vertical position, proceed in the
same manner.
If your wheelchair features drum brakes, the
handles are used as brakes; additional levers
have been mounted for back rest adjusting.
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vermeiren Eclips plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vermeiren Eclips plus in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 4,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info