514915
15
Zoom out
Zoom in
Previous page
1/20
Next page
DX2 Operator control
vD - 2013-04
14
2. Troubleshooting
DX2 Basic (without LCD screen)
Symbol flickering fast at intervals. The number of flashes per interval provides the
information below (the following actions and checks should only be carried out by authorised
individuals).
DX2 with LCD screen
The following diagnoses refer to all the electronics. The flashing code is read from the status display
on the DX2 steering and control unit. The various modules for steering, power, and lamps, have their
own light signals indicating the status of the module concerned (steady light = OK; flashing light =
defective).
This fault analysis aids problem analysis and problem solving by indicating the possible faults. If faults
arise which cannot be identified and remedied with the aid of this analysis, kindly contact the
manufacturer. We wish to point out that in any case of improper handling or if the delivered
configuration has been changed, we cannot guarantee the accuracy of the fault indications.
DX2: The status display shows the workshop ID with the code number.
Number
Problem/Fault Checks
0
There is no indication of
the charge level of the
batteries after the
steering unit is switched
on.
1. Check whether the battery plug is inserted fully and correctly
connected to the socket of the steering unit.
2. Check whether the two batteries are connected correctly.
3. Check whether the batteries are charged.
4. Check whether the thermal fuse is defective or loose.
1
One of the DX modules
is defective (controls,
power module, light
module, CLAM module).
1. If the control unit's module LED flashes, the control unit should be
replaced.
2. If the power module diode flashes, this module must be replaced.
3. If the lamp module diode flashes, this module must be replaced.
L
If the steering and control unit has to be replaced, a new error
code might be indicated, since a complete fault analysis could
not be carried out.
2
A module connected to
the power module is
defective.
Check the condition of the connected module.
3
Left motor (or its
connection) is defective.
1. Check whether the plugs of both motors have been inserted properly.
2. Check the plug contacts of both motors for corrosion or damage.
3. Check both motors. Unplug the motors and measure the plug
connection with an Ohm meter. If you obtain readings of more than 1
Ohm or less than 100 milliOhms, the motor is defective.
4. Check the resistance of the motor. Measure every contact using an
Ohm meter.
L
A Fault is also indicated if the motors are disconnected.
Connect again and restart the system.
4
Right motor (or its
connection) is defective.
As described above.
5
Left parking brake (or its
connection) is defective
or neutral active.
1. Check whether the motors' plugs have been inserted properly.
2. Check the plugs for corrosion or damage.
3. Check the parking brakes. Measure the resistance of the connections
by means of an Ohm meter. If the resistance value is above 100
Ohms or beneath 20 Ohms, the parking brake is probably defective.
6
Right parking brake (or
its connection) is
defective.
As described above.
7
Battery voltage too low 1. Check that the charger provided is properly connected.
2. Check whether the battery charger indicates "Charging".
3. Check whether the batteries are really being charged (deep
discharge)
4. Check whether the so-called "memory effect" has resulted in the
battery no longer being able to generated the capacity to enable the
control elements to work properly.
2
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vermeiren Controleunit D2X at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vermeiren Controleunit D2X in the language / languages: English as an attachment in your email.

The manual is 1,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Vermeiren Controleunit D2X

Vermeiren Controleunit D2X User Manual - Dutch - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info