Manual Vermeiren Carpo 4 (page 21 of 136) (English, German, Dutch, French, Italian, Polish, Spanish)

658531

Zoom out

Zoom in

1/136

Instruction manual Carpo 3 / Carpo 4

Last updated: 2017-02

Carpo 4:

DISMANTLING

1. Remove the cover cap for scooter rim.

2. Unscrew and remove the middle screw that attach the wheel and flange to the scooter.

3. Let the air out of the wheel by lightly pressing the pressure pin on the valve.

4. Unscrew the 4 screws of the rim to separate the rim sides and flange.

ASSEMBLY

Insert the partly-filled inner tube into the tyre.

1. Connect the two sides of the rim through the tyres and place the flange against the tyre and screw

them back again with the 4 screws.

2. Put the air valve through the hole for it in the rim.

3. Put the wheel and flange back on the scooter and secure these connection with the middle screw.

Inflate the wheel to the recommended tyre pressure.

4. Replace the cover cap.

Check all around on both sides that the tube is not pinched between the rim and the edge of the tyre.

Lightly push the air valve inwards and pull it out again to make sure that the tyre is positioned properly

in the region of the air valve.

To ensure that the wheel is inflated correctly, admit only so much air initially that the tyre can still be

easily pushed inwards by using your thumbs. If the check-lines are equidistant from the edge of the

rim on both sides of the tyre, then the tyre is centered properly. If not - let out the air and position the

tyre afresh. Now the tyre can be inflated to its full operating pressure (note the maximum) and the

valve cap should be replaced.

Only an expert can guarantee correct assembly. Work not done by your specialist dealer, would void

any warranty claims.

When inflating the tyres, always check that the pressure is correct. The correct pressure is given on

the tyre walls.

Use only inflating equipment which complies with regulations and indicates the pressure in bar. We do

not accept any liability for damage caused by using inflation equipment not supplied by the

manufacturer.

DISASSEMBLING & ASSEMBLING

The chassis – situated below the seat and arm rests – can also be taken apart. Proceed as follows:

 Switch the scooter off

 Remove the seat (see “Seat” chapter).

 Lift off the rear plastic cover (held in place by Velcro fasteners).

L Bear in mind that the cables of the rear lights are connected to the plastic cover. Unplug the

plugs before entirely removing the plastic cover.

 Unplug all battery plugs (not the pole connectors) and all cable plug- and socket connections.

 Loosen the straps used to fasten the batteries in place.

 Lift the batteries out.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Vermeiren Carpo 4 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 6,8 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Vermeiren Carpo 4 Manual

Product: