714720

Veritas Janis Manual

52
Zoom out
Zoom in
Previous page
1/76
Next page
50
Set the machine as illustrated above.
- Remove the presser foot and the presser foot
holder.
- Attach the darning plate.
- Lower presser foot lifter before starting to
sew.
Prepar a t i o n fo r Monogramming an d
Embroidering
- Draw the desired lettering or design on the
right side of the fabric.
- Stretch the fabric between embroidery hoop
as firmly as possible.
- Place the fabric under the needle. Make sure
the presser foot bar is down in its lowest
position.
- Turn the balance wheel towards you to bring
up the lower thread through the fabric. Sew a
few securing stitches at the starting point.
- Hold the hoop with thumb and forefingers of
both hands while pressing the material with
the middle and third fingers and supporting
the outside of hoop with smaller finger.
- Adjust the stitch width according to the size of
lettering or design.
* Embroidery hoop not included with machine.
Recouvrement des griffes d'entraînement
- Réglez la machine comme illustré ci-contre
.
- Déposez le pied presseur et son support.
- Montez la plaque couvre-entraînement.
- Abaissez le levier releveur de pied presseur
avant de commencer à coudre.
- Ajustez la largeur du point en fonction de la
taille des lettres ou du motif.
Préparation en vue de la réalisation d'un
monogramme et d'une broderie
- Dessinez les lettres ou le motif désiré sur
l'envers du tissu.
- Tendez le tissu le plus possible sur le cercle à
broder.
- Placez le tissu en dessous de l'aiguille.
Assurez-vous que le montant du pied
presseur est descendu à sa position la plus
basse.
- Tournez la commande d'équilibrage vers
vous de manière à faire remonter le fil
inférieur à travers le tissu. Cousez quelques
points d'arrêt au point de départ de la
broderie.
- Maintenez le cercle à broder au moyen du
pouce et de l'index de chaque main, tout en
appuyant sur le tissu avec le majeur et
l'annulaire et en soutenant l'extérieur du
cercle avec l'auriculaire.
* Le cercle à broder n'est pas fourni avec la
machine.
Transporteurafdekplaat aanbrengen
- Stel de machine in als op de tekening te zien
is.
- D e m o n t e e r d e p e r s v o e t e n d e
persvoethouder.
- Monteer de transporteurafdekplaat
- Trek de persvoethendel omlaag voor u met
naaien begint.
- Selecteer de steekbreedte aan de hand van
de lettergrootte of het Motief.
Voorbereidingen voor monogrammen en
borduren
- T e k e n d e l e t t e r s o f h e t m o t i e f o p d e
achterzijde van de stof.
- Span d e s t o f z o stra k m o g e l i jk op h e t
borduurraam.
- Leg het werk onder de naald. Kijk of de
persvoethouderstang zich in de laagste stand
bevindt.
- Draai het handwiel en trek de onderdraad
door de stof omhoog. Maak op het beginpunt
een paar aanhechtingssteken.
- Neem het borduurraam tussen de duim en
wij sving er van elk e hand, dru k met de
middelvinger en de ringvinger op de stof en
steun de buitenkant van het borduurraam op
de pink.
Monogrammen / Borduren
Monogrammes et Broderie
Monogramming
FR
NL
EN
… 52 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Veritas Janis at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Veritas Janis in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info