556666
8
Zoom out
Zoom in
Previous page
1/13
Next page
- Single press [0] button. The reading will reset to zero and the “TARE” icon will remain on the upper display.
Now you can add your additional ingredient. Only the weight or volume of the last ingredient added in measured. Continue
above procedure to build up different ingredients for your recipe.
NOTE: The tare function only operate when the cup is placed on a flat surface
Reversing the Tare Function
Right after the tare function has been performed and the display is showing “0” reading with the “TARE” icon appeared, you
can press [0] button to resume the original weight or volume reading just before the tare function and the “TARE” icon will
disappear.
NOTE: The reverse tare function only operate when the cup is placed on a flat surface
IMPORTANT NOTE
: It is easy and convenient to mix different ingredients in the cup. However when mixing your ingredients,
you should avoid pressing down the bottom of the base where the sensitive weight scale components are located.
Excessive force applied to the base of the cup may permanently damage the scale inside and provide inaccurate reading.
FAULT MESSAGE DISPLAY
UnSt: Unstable
The scale is unstable and the unit will turn off automatically. Place the cup on a flat table and
turn on the unit again by pressing [0] button once.
Err: Error
The scale is overloaded. The weight or volume in the cup exceeds the maximum display
range (refer “Specification” section)
CALIBRATION
To ensure accurate measurement, you are suggested to check the weight of an empty cup every time you first turn on the
unit. It should read 0 gram (or oz) for your empty cup.
Calibration for the cup is needed ONLY when the reading of your EMPTY cup is higher than zero (gram, oz, cups, fl oz or
ml). The calibration process will reset the reading to zero for the empty cup.
To calibrate,
1) Make sure the transparent cup is attached to the base.
2) Make sure the cup is empty. Clean the unit with a dry cloth to remove any excess liquid on the cup.
3) Turn on the unit by a single press of the [0] button.
4) Make sure the cup is placed steadily on a flat surface. Hold [0] for 6 seconds until “CAL” flashes. Do not touch or move
the cup when “CAL” is flashing.
The display reading will show “0” and the calibration is completed
CLEANING AND STORAGE
- The transparent cup is dishwasher safe and it is detachable for cleaning. Press the button below the handle to unlock
and detach the cup from the base
- Only clean the transparent cup with cold or warm water together with optional mild cleaning detergent. Do not use
boiling water to clean the transparent cup as it can withstand up to 70C maximum.
- Detach the transparent cup and use damp cloth to clean the base and the handle.
- Never immerse the base & handle in water or put into dish washing machine for cleaning
7
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ventus W164 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ventus W164 in the language / languages: English, German, Danish as an attachment in your email.

The manual is 0,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info