488178

Venga VG VC 4 Manual

9
Zoom out
Zoom in
Previous page
1/44
Next page
Copies of the I/B. Please reproduce them without any
changes except under special instruction from Team
International BELGIUM. The pages must be reproduced and
folded in order to obtain a booklet A5 (+/- 148.5 mm width x
210 mm height). When folding, make sure you keep the good
numbering when you turn the pages of the I/B. Don’t change
the page numbering. Keep the language integrity.
Fax +32 2 359 95 50
ASSEMBLING THE VACUUM CLEANER
Always remove the plug from the power socket before fitting or removing accessories! •
•
•
•
•
•
•
•
•
•
•
•
•
•
Insert the hose connector into the hose connection inlet until it locks. To remove the hose,
press the sides of the hose connector and pull at the hose.
Fit the tube to the handle.
Fit the tube to the floor brush.
You can adjust the length of the tube.
Removing tube and accessories: to remove the accessories, pull firmly apart.
The floor brush is ideal for the daily cleaning of carpets and hard floors.
Setting with the bristles inside for cleaning carpets.
Setting with the bristles outside for cleaning hard floors.
• The appliance is delivered with the following accessories:
a crevice tool: for radiators, crevices, corners, baseboards
and between cushions.
an upholstery brush: for curtains, cushions, edges, doors,
mattresses etc.
OPERATION
Pull out a sufficient length of power cord and insert the plug into the power socket. A
yellow mark on the power cable shows the ideal cable length. Do not extend the cable
beyond the red mark. Switch on the appliance by pressing the ON/OFF switch with your
foot.
You can adjust the suction power by using the wind-force adjuster on the handle of the
flexible hose. Use a low suction power for furniture and other delicate surfaces and use
high suction power for fitted carpet and other floors.
AFTER USE
Stop the vacuum cleaner by pressing the ON/OFF switch.
Unplug the appliance from the power supply.
Simply press the cable rewind button to activate the cable rewind mechanism.
The carrying handle can be used to move the appliance. Never use the handle of the
dust container to carry the appliance!
After use we advise you to empty the dust collector to avoid smells and mildew that could
be caused by damp dust particles that may have been vacuumed, and also to
guarantee an optimal efficiency during the next use. To do so, see below.
EMPTYING THE DUST COLLECTOR
• Press the release button of the dust container and pull the dust container out.
• Hold the dust collector over a dustbin, press the unlocking button at the bottom of the
handle of the dust collector to open the lower cover of the dust container and spill the
rubbish.
• Close the dust collector and put the dust collector back in the appliance until it locks in
place.
9 VG VC 4 - 101220
Assembly page 9/44
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Venga VG VC 4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Venga VG VC 4 in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 1,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info