488140

Venga VG MGR 1 Manual

11
Zoom out
Zoom in
Previous page
1/44
Next page
Copies of the I/B. Please reproduce them without any changes except
under special instruction from Team International BELGIUM. The page
must be reproduced and folded in order to obtain a booklet A5 (+/-
148.5 mm width x 210 mm height). The page must be folded in order to
keep the good numbering when you turn the page of the I/B. Don’t
change the page numbering. Keep the language integrity.
11 VG MGR 1 - 101213
IMPORTANT INFORMATION
This appliance is not intended for professional use. You should follow the requested breaks.
Failure to follow this instruction carefully may result in damage to the motor. Please refer to the
rating label for the maximum continuous usage time (KB xx min where xx is the maximum usage
time). The breaks should last at least 10 minutes.
BEFORE THE FIRST USE
Check that the voltage indicated on the rating label corresponds to the mains voltage in your
home.
Wash all parts (except the body) in warm soapy water.
Before plugging in, ensure the “ON/OFF/Reverse” switch is turned to the "OFF" position.
INSTRUCTIONS FOR USE (see page 5)
ASSEMBLING
Hold the head and insert it into the inlet with one hand (fig. 1), place the locking knob into the
hole on the side of the motor housing with the other hand, and tighten it clockwise to secure the
head (fig. 2).
Place the feed screw into the head, long end first, by turning the feed screw slightly until it is set
into the motor housing (fig. 3).
Place the cutting blade onto the feed screw shaft with the blade facing the front as illustrated
(fig. 4). If it is not fitted properly, meat will not be ground.
Place the desired cutting plate next to the cutting blade, fitting protrusions in the slots (fig. 5).
Support or press the centre of the cutting plate with one finger, then screw the fixing ring until
tight with the other hand (fig. 6). Do not overtighten.
Place the hopper plate on the head and fix into position.
Locate the unit on a firm place.
The air passage at the bottom and the side of the motor housing should be kept free and not
blocked.
MINCING MEAT
Cut all foods into pieces (sinewless, boneless and fatless meat is recommended, approximate
size: 20 mm x 20 mm x 60 mm) so that they fit easily into the hopper opening.
Plug in and turn the “R / ON” switch to "ON" position, then turn the “ON/OFF/Reverse” switch to
"ON" position.
Feed foods into the hopper plate. Use only the food pusher (fig. 7).
After use, switch the unit off and unplug it from the power supply.
REVERSE FUNCTION
In case of jamming, switch the appliance off by turning the “R / ON” switch to
"R" position and the “ON/OFF/Reverse” switch to "R" position.
The feed screw will be rotating in the opposite direction, and the head will get empty.
If it doesn't work, switch the unit off and clean it.
Assembly page 11/44
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Venga VG MGR 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Venga VG MGR 1 in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 1,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info