488070

Venga VG FT 1 Manual

10
Zoom out
Zoom in
Previous page
1/52
Next page
Copies of the I/B. Please reproduce them without any changes
except under special instruction from Team International BELGIUM.
The pages must be reproduced and folded in order to obtain a
booklet A5 (+/- 148.5 mm width x 210 mm height). When folding,
make sure you keep the good numbering when you turn the pages
of the I/B. Don’t change the page numbering. Keep the language
integrity.
10
VG FT 1 - 101217
Assembly page 10/52
Fax +32 2 359 95 50
preparation is ready and the fryer is no longer in use. Before pulling the mains plug, switch
the temperature selector to "MIN".
Provide proper ventilation when using the appliance.
If you wish to use solid fat, cut it into small pieces and place them into the bowl. Turn the
temperature knob to its minimum position. Each time the pilot light goes out, turn the
temperature knob to a slightly higher temperature until all the fat has melted. Once all the
fat has melted, set the temperature knob to the desired cooking temperature. This type of
fat will solidify when the appliance cools down.
Your appliance must never be switched on through an external timer or any kind of
separate remote control system.
(*)
Competent qualified electrician: after-sales department of the producer or importer or any
person who is qualified, approved and competent to perform this kind of repairs in order to
avoid all danger. In case of need you should return the appliance to this electrician.
BEFORE USE
• Remove all packaging from the unit.
• Remove the lid, basket, handle and any accessory from the appliance.
• Before you use the deep fat fryer for the first time, we recommend that you clean the lid,
bowl, basket, handle and housing of the deep fat fryer with warm soapy water with a soft
cloth.
DISASSEMBLING THE DEEP FAT FRYER
• Remove the control panel from the appliance. To do this, gently pull the control panel
upwards until it is released.
• Take the interior bowl with your two hands and pull it up gently.
ASSEMBLING THE DEEP FAT FRYER
• Stand the appliance on a dry horizontal surface.
• Place the bowl back in the housing and push it downwards.
• Replace the control panel and the accessories. To replace the control panel, firmly slide
the control panel downward into the location grooves on the back of the housing until it is
locked.
• NOTE: The appliance will only operate when the control panel is correctly fitted to the
outer jacket.
• Press the end of the basket's handle together, insert its pins into the holes foreseen on the
basket and unfold the handle of the basket until it is locked to allow rising the basket
easily.
• Put the remaining power cord length in the cord storage in the back of the appliance.
FIRST USE
• When using the appliance for the first time, pour the required amount of oil in the bowl,
making sure that the level is between the MIN and MAX marks indicated inside the bowl.
• We recommend that you use a liquid oil that is suitable for deep fat frying. Check the
label on the bottle. If you wish to use a solid fat, cut the fat in small pieces. Plug in the
appliance, put the thermostat on the minimum position and add the pieces of fat slowly.
When the fat has melted, set the thermostat to the desired temperature. WARNING:
FAILURE TO OBSERVE THIS WILL DAMAGE YOUR DEEP FAT FRYER.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Venga VG FT 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Venga VG FT 1 in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 1,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info