567745
16
Zoom out
Zoom in
Previous page
1/29
Next page
16
Subwoofer Controls/Connections/Features Wi-Q User’s Manual
Following are descriptions of the controls and connections shown in Figure 8.
Power: Turns the subwoofer on/off. Even if you are using the Auto on/off feature, this switch must be in
the ON position for the subwoofer to receive power.
Power Connector/Fuse Drawer: Connects the subwoofer to a wall outlet so that it can receive power. The
fuse drawer is located at the bottom of the power connector.
Speaker Level Input: If you’re not using the transmitter, you can connect these input terminals to the
speaker output terminals on your amplifier or receiver. For this connection method, go to your receiver’s
Speaker Setup menu and select the Large speaker option.
Speaker Level Output: If you’re using speaker-level inputs, you can use these terminals to send a
crossed-over speaker-level signal to the front speakers. See Low-Pass Crossover: for details on this
crossover.
IR Input: This connection supports third-party infrared remote sensors, such as Elan or Xantech, for
placement closer to your other remote controlled equipment. Use this feature to avoid awkward angles
when using the remote control.
Line Output: If you’re using line-level inputs, you can connect these jacks to the LINE IN input on your
preamp. With this connection method, you use the Wi-Q’s internal high-pass crossover, which rolls off
below 80 Hz.
Line Input/LFE: If you’re not using the transmitter, you can connect these jacks to one of the following:
LINE OUT output on your preamp
LFE on your receiver/processor
Subwoofer output on your receiver/processor
Note: When using the LFE output, plug a single cable into the L – LFE input, or for more signal,
use a “Y” connector (not included) and feed the signal into both R and L inputs.
Stand By Mode/Always On: When this switch is in the STANDBY MODE position, the subwoofer
automatically turns itself on when an audio signal is present. If there’s no signal for about thirteen minutes,
the unit switches to standby mode (blank LED), which draws minimal power. The default setting for this
switch is ALWAYS ON. To activate the Auto on/off feature, slide this switch to the STANDBY MODE
position.
Volume Up/Down: Use these controls to achieve balanced volume levels between your main speakers
and the subwoofer. When you press Volume Up/Down, the LED displays the current volume setting. You
can also adjust subwoofer volume with the remote control. The default volume setting is 30 out of 80.
Channel: This control sets the channel used for wireless communication between the subwoofer and the
transmitter. Make sure that the channel selection is the same on both the subwoofer and transmitter.
Warning
If the signal level from your receiver’s Sub-out channel is weak, the subwoofer shuts off while
you are listening to it. To correct this issue, see the next section,
Volume Up/Down:.
Warning
Some receivers are preset with the Sub-out channel set at a minimum level. If your receiver
Sub-out channel is too low, the subwoofer may have weak output, sound noisy or distorted,
and the Auto on/off feature may not operate properly.
To avoid these issues, make sure that your receiver’s Sub-out channel is set to the same
output level as your front right and left channels. Refer to your receiver’s manual for details
on adjusting the individual channel levels.
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Velodyne Wi-Q12BVE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Velodyne Wi-Q12BVE in the language / languages: English as an attachment in your email.

The manual is 4,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info