567742
20
Zoom out
Zoom in
Previous page
1/29
Next page
20
Remote Control Wi-Q User’s Manual
Remote Control
This section describes how to use your Wi-Q subwoofer remote control.
Power: Puts your subwoofer in reduced-power mode, which stops play
and turns off the display. Press this button again to return to full operation.
This function is subordinate to the standby mode on the rear panel, and
you must restart the subwoofer if that feature has triggered. To fully turn off
the subwoofer, press the POWER switch on the back of the subwoofer.
Mute: Silences the subwoofer’s output and the LED on the sub shows 00.
To unmute the subwoofer, press the MUTE button again and the original
volume setting shows on the LED.
EQ: Runs the automatic equalizer, so your Wi-Q subwoofer sounds best
for its position in the room. See Step 6: Run Auto-EQ for details on using
this feature.
Phase: Optimizes the subwoofer’s bass performance relative to the
speakers and your listening position. This control changes the phase of the
subwoofer’s output signal to correct mismatches and resulting
cancellation between the subwoofer and your main speakers/amplifier.
The phase setting shows on the LED as “PH” followed by the phase
number: 0, 90, 180 or 270. See Step 7: Set the Phase for details on using
this feature.
Light: Turns the numeric LED on your subwoofer off. To reactivate the LED,
press the LIGHT button again. When the LED is off, it lights only when you
make adjustments to the subwoofer controls and then turns off again.
Night: Limits the maximum dynamic output of the subwoofer for late night
listening or considering close neighbors at any time. Press the NIGHT
button to turn night mode on/off. When you activate night mode, the LED
briefly displays “n.” When you deactivate night mode, the LED shows “n
off” and then returns to normal function.
Volume Control: Balances the output from the subwoofer to the main
speakers in your system. Use this control to achieve similar volume levels
from both the main speakers and subwoofer. When pressing volume up or down, the LED displays the volume level.
Note: The remote control included with your specific subwoofer may not look the same as the remote
control shown in the illustration, but the functions and performance are identical to those described here.
Note: You can also adjust the subwoofer’s volume with the Volume buttons on the back of the
subwoofer. These buttons have the same effect as pressing the up and down volume buttons on your
remote. The default volume setting is 30 out of 80.
Warning
Some receivers are preset with the Sub-out channel set at a minimum level. If your receiver Sub-out
channel is too low, the subwoofer may have weak output, sound noisy or distorted, and the Auto on/off
feature may not operate properly.
To avoid these issues, make sure that your receiver’s Sub-out channel is set to the same output level as
your front right and left channels. Refer to your receiver’s manual for details on adjusting the individual
channel levels.
EQ Mute PWR
12
34
0
270 90
180
Light Night
+
-
Jazz Games
Movies Rock
Presets
Volume
Phase
Figure 12: Wi-Q Remote
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Velodyne Wi-Q10BV at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Velodyne Wi-Q10BV in the language / languages: English as an attachment in your email.

The manual is 4,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info